1. Safety Information
When the power is on, the soldering iron tip temperature is between 100°C-450°C (212°F-842°F). Improper use can lead to burns or fire. Please strictly observe the following safety guidelines:
- Do not touch the soldering iron tip or nearby metal parts when hot.
- Do not use near flammable materials.
- Inform others in the workspace that the soldering iron tip is hot and can cause dangerous accidents.
- Always turn off the power when resting or after completing work.
- When replacing components or the soldering iron tip, turn off the power and wait for the tip to cool to room temperature.
- This product uses the rated voltage and frequency (refer to the label on the back of the machine).
- Do not use the product if it is damaged, especially if the power cable is compromised.
- This product uses a three-wire grounding plug and must be inserted into a three-hole grounded socket. If an extension cord is needed, use a grounded three-wire power cord.
- Do not use the soldering iron for any work other than welding.
- Do not knock the soldering tip on the workbench to clean it, as this can seriously damage the tips.
- When replacing parts, use original factory parts.
- Do not tamper with the soldering iron without proper safety precautions.
- Do not wet the soldering iron, and do not use it with wet hands.
- Ensure adequate ventilation when soldering, as smoke will be produced.
- Keep the soldering station out of reach of children.
2. Product Overview
The AIFEN A5 Soldering Station is a high-performance electronic tool designed for precision soldering and rework tasks. It features 120W power, rapid heating, and compatibility with C210, C245, and C115 series soldering iron tips.
3. Setup Instructions
Note: Always ensure the power is off when connecting or disconnecting the handle to prevent damage to the control circuit board.
- Connect the Handle: Insert the soldering iron handle device into the handle socket on the main unit.
- Install Heating Core/Tip: Install the required heating core (soldering tip) into the handle.
- Position the Station: Place the soldering station on a stable surface and rest the handle securely in its holder.
- Connect Power: Connect the power supply cable to the soldering station and then to a grounded power outlet.
- Power On: Turn on the power switch. The display window will show "---", indicating the soldering station is in standby mode.
4. Operating Instructions
4.1. Temperature Adjustment
The AIFEN A5 allows for precise temperature control within a range of 100°C-450°C (212°F-842°F).
- Increasing Temperature: Press the ▲ button once to increase the set temperature by 1°C. If you press and hold the ▲ button for at least one second, the temperature will rise rapidly until the button is released at the desired temperature.
- Decreasing Temperature: Press the ▼ button once to decrease the set temperature by 1°C. If you press and hold the ▼ button for at least one second, the temperature will fall rapidly until the button is released at the desired temperature.
4.2. Celsius and Fahrenheit Conversion
To switch between Celsius and Fahrenheit display modes:
- While the unit is powered on, press and hold the ▲ button to toggle between Celsius and Fahrenheit.
4.3. Temperature Calibration
To calibrate the temperature:
- With the main unit powered off, press and hold both the ▲ and ▼ buttons simultaneously, then turn on the power. This will enter the ±99 degree temperature calibration mode.
- Use the ▲ or ▼ button to adjust the calibration value.
- The setting will automatically save and exit after 3 seconds of inactivity.
4.4. Standby Temperature Setting
To set the standby temperature:
- With the main unit powered off, press and hold the ▼ button, then turn on the power. This will enter the standby temperature setting interface.
- Available standby temperatures are 0°C, 150°C, 180°C, 200°C. Setting to 0°C will turn off the standby temperature function.
- The setting will automatically save and exit after 3 seconds of inactivity.
4.5. Handle Control Operations (Wire-Controlled Version Only)
For the wire-controlled version of the A5, the handle offers additional functions:
- Handle Temperature Adjustment: In working state, press the temperature adjustment buttons on the handle to increase or decrease the temperature.
- Handle Control Machine Switch: In working state, press and hold both temperature adjustment buttons on the handle simultaneously to turn the host interface on/off.
Note: These handle control functions are only available on the wire-controlled version of the A5. The normal version does not have these features.
5. Maintenance
5.1. Soldering Tip Temperature Management
High temperatures can weaken the soldering tip's performance. Always choose the lowest possible temperature that allows for effective soldering. The AIFEN A5 tips have excellent temperature recovery, enabling soldering at lower temperatures to protect temperature-sensitive components.
5.2. Cleaning the Soldering Tip
- Regular Cleaning: Use a clean sponge or copper wire cleaning ball to clean the tip regularly. After welding, residual flux can form oxides and carbides that damage the tip, cause welding errors, or reduce heat conduction.
- Post-Use Care: After use, clean the soldering iron tip and coat it with a new layer of tin (tinning) to prevent oxidation.
- Checking Tip Condition: After the temperature stabilizes (e.g., at 250°C / 482°F), clean the tip with a copper wire cleaning ball and inspect its condition.
- Removing Black Oxide: If the tinned part of the tip has black oxide, apply a new tin layer, then wipe with a clean sponge until the oxide is completely removed. Re-tin the tip.
- Tip Replacement: If the soldering tip is deformed or heavily rusted, it must be replaced.
5.3. Heating Core Replacement
This soldering station uses an integrated heating core and soldering head. To replace:
- Turn off the power and allow the unit to cool down completely.
- Carefully unplug the old heating core/tip assembly.
- Plug in the new heating core/tip assembly.
6. Troubleshooting
This section provides general guidance for common issues. For complex problems, please refer to the official support channels.
| Problem | Possible Cause | Solution |
|---|---|---|
| Station does not power on | Power cable not connected, faulty power outlet, main switch off. | Check power cable connection, try a different outlet, ensure main switch is ON. |
| Temperature not reaching set value or unstable | Heating core/tip not properly installed, worn out heating core, incorrect temperature setting. | Ensure heating core is fully inserted. Replace heating core if old. Verify temperature settings. |
| Poor solder joints / Solder not adhering | Dirty or oxidized soldering tip, incorrect temperature, old solder. | Clean and re-tin the soldering tip. Adjust temperature. Use fresh solder. |
| Error message on display | Internal fault, sensor issue. | Turn off the station, wait a few minutes, then restart. If the error persists, contact support. |
7. Specifications
| Feature | Detail |
|---|---|
| Model Number | AIFEN-A5 |
| Brand Name | AIFEN |
| Origin | Mainland China |
| Input Voltage | AC100-240V 50/60Hz |
| Power | 120W |
| Max Power | 160W |
| Temperature Control Range | 100°C-450°C (212°F-842°F) |
| Compatible Tips | C210, C245, C115 series heating cores/tips |
| Certification | CE |
8. User Tips
- Tip Selection: Users have noted excellent performance with C115 tips, suggesting that selecting the appropriate tip for your specific task can significantly enhance efficiency and results.
- Efficient Operation: The station is designed for efficient operation, heating up quickly. Utilize the rapid temperature adjustment features for seamless workflow.
9. Warranty and Support
For detailed information regarding product support, please refer to the official user manual PDF provided by the manufacturer. This document contains comprehensive instructions and diagrams that may not be fully replicated here.
The official user manual (PDF) can be accessed via the following link: AIFEN A5 User Manual (PDF).
For further assistance or specific inquiries, please contact the seller or manufacturer's customer support.