1. Safety Information
Warning:
- This device is for indoor use only.
- This device should not be exposed to dripping or any danger sources.
- This device should only be installed by adults.
- Do not install near any heat sources.
- Do not use this device with dimmers.
- Do not use this device in a fully enclosed fixture.
- Pay attention to electricity and do not use it in humid places.
- If the unit is heavier than the replacement unit, it may reduce the stability of some fixtures and affect the contacts.
2. Product Overview
The QIACHIP 433MHz Wireless Light Switch system provides a convenient way to control your lighting without the need for traditional in-wall wiring. It consists of a receiver (Model KR2201GS) and wall panel transmitters (Model WP8601) that communicate wirelessly via RF 433MHz.
Key features include:
- No in-wall wiring needed for wall panel installation.
- Wall switch mounts anywhere.
- 100 ft RF Range for flexible control.
- Programmable and Expandable system.
- Suitable for various applications such as adding a wall switch, replacing hard-to-reach switches, multi-way switching, and controlling several lamps simultaneously.
3. Installation
The QIACHIP wireless switch system offers flexible installation options. The receiver (KR2201GS) requires wiring to the light fixture, while the wall panel transmitters (WP8601) can be mounted anywhere without in-wall wiring.
3.1 Receiver Wiring Diagrams (KR2201G/KR2201GS)
Ensure power is OFF before performing any wiring. Wiring should only be performed by qualified adults.
3.1.1 KR2201G Wiring (Remote Control Only)
This configuration is for controlling the light solely via the wireless remote control. The receiver acts as an intermediary between the AC power supply (90V-250V) and the light fixture.
- Connect the Live (L) and Neutral (N) wires from the AC power supply to the 'IN' terminals (L and N) on the KR2201G receiver.
- Connect the Live (L) and Neutral (N) wires from the light fixture to the 'OUT' terminals (L and N) on the KR2201G receiver.
3.1.2 KR2201GS Wiring (Remote Control + External Switch)
This configuration allows for simultaneous control using both the wireless remote control and a traditional external wall switch. The external switch connects to the 'S' terminal on the receiver.
- Connect the Live (L) and Neutral (N) wires from the AC power supply (90V-250V) to the 'IN' terminals (L and N) on the KR2201GS receiver.
- Connect the Live (L) and Neutral (N) wires from the light fixture to the 'OUT' terminals (L and N) on the KR2201GS receiver.
- Connect one wire from the external switch to the 'S' terminal on the KR2201GS receiver.
- Connect the other wire from the external switch to the Live (L) wire of the AC power supply.
4. Operation
The QIACHIP wireless switch system allows for flexible control modes and easy pairing.
4.1 Pairing Remote Control Transmitters (WP8601)
The receiver (KR2201GS) has a Smart Circuit Breaker Pairing Button. This button is used to enter different pairing modes.
4.1.1 Toggle Mode Setting
In Toggle Mode, pressing the remote control button once turns the light ON, and pressing it again turns the light OFF.
- Press the setting button on the Smart Switch receiver twice.
- The red indicator light on the receiver will flash and then light up.
- Within 5 seconds, press the button on the remote control transmitter that you wish to pair.
- When the red indicator light flashes and goes out, the Toggle Mode setting is successful.
4.1.2 Latch Mode Setting
In Latch Mode, one button on the remote control turns the light ON, and another button turns it OFF.
- Press the setting button on the Smart Switch receiver three times.
- The red indicator light on the receiver will flash and then light up.
- Within 5 seconds, press the button on the remote control that you want to set as the "ON" button (e.g., Button A).
- Then, press the button on the remote control that you want to set as the "OFF" button (e.g., Button B).
- The red indicator light will flash to confirm that the Latch Mode is successfully set.
4.1.3 Push Button Mode Setting
In Push Button Mode, the light remains ON only while the remote control button is pressed.
- Press the setting button on the Smart Switch receiver four times.
- The red indicator light on the receiver will flash and then light up.
- Within 5 seconds, press the button on the remote control transmitter that you wish to pair.
- When the red indicator light flashes and goes out, the Push Button Mode setting is successful.
4.2 Pairing with an External Switch (KR2201GS only)
The KR2201GS receiver can also be paired with a traditional external toggle switch to control the learning state for remote controls.
4.2.1 Toggle Mode Setting (External Switch)
- Connect the KR2201GS to the power supply and the light fixture.
- Press the external switch five times in a row.
- The light will flash three times and stay on, indicating pairing mode.
- Within 5 seconds, press the corresponding button on the remote control to pair.
- The light will turn off when pairing is complete.
- Note: If no pairing occurs within 5 seconds, the load will remain connected and exit pairing mode.
4.2.2 Latch Mode Setting (External Switch)
- Connect the KR2201GS to the power supply and the light fixture.
- Press the external switch six times in a row.
- The light will flash three times and then stay on, indicating that it has entered the pairing mode.
- Within 5 seconds, press the button on the remote control that you want to set as the "ON" button (e.g., Button A).
- The load will disconnect and reconnect 3 times, and then stay connected.
- Next, press the button on the remote control that you want to set as the "OFF" button (e.g., Button B).
- The load will disconnect and reconnect 3 times, and then turn off.
- Note: If no pairing occurs within 5 seconds, the load will remain connected and exit the pairing mode.
4.3 Resetting Paired Transmitters
To clear all paired transmitters from the receiver's memory:
4.3.1 Reset via Receiver Button
- Press the receiver button twice.
- Wait until the light stops flashing (for the old appearance version, it's the indicator light on the receiver that flashes).
- At this time, press the button on the transmitter to be paired to send out the signal.
- Press the receiver button 8 times consecutively.
- All paired transmitters are disabled, and the receiver clears its memory.
4.3.2 Reset via External Switch (KR2201GS only)
- Connect the KR2201GS to the power supply and lamp.
- Press the external switch 8 times in a row.
- The light will flash 3 times before turning off.
- Reset is complete; all remote control data is erased.
5. User Tips
- The wall panel switches (WP8601) do not require batteries, making them maintenance-free.
- Ensure the receiver is correctly wired and powered before attempting any pairing procedures.
- When pairing, perform the steps within the specified 5-second window for successful registration.
- If using an external switch for pairing, ensure it is a toggle switch type.
6. Troubleshooting
- Light not responding after pairing: Ensure the receiver is powered and correctly wired. Re-attempt the pairing process, paying close attention to the indicator light's behavior.
- Remote control range issues: The specified range is 100ft in an open area. Obstacles like thick walls or metal structures can reduce this. Try repositioning the receiver or testing in a less obstructed environment.
- Accidental unpairing: If the switch suddenly stops working, it might have been accidentally reset. Follow the pairing instructions again for your desired mode.
- Light flickering or not turning off completely: Ensure the device is not used with dimmers or in fully enclosed fixtures, as specified in the safety information. Check the load capacity against the specifications.
7. Product Specifications
| Feature | Specification |
|---|---|
| Model Numbers | KR2201GS and WP8601 |
| Power Input | AC 90-250V 50/60Hz |
| Max Current Load | 10A |
| Max Load Power | 2200W (AC220V) |
| Incandescent Lamp Load | 500W |
| Capacitive Load | 200W |
| Energy-saving Lamp Load | 300W |
| RF Working Frequency | 433.92MHz |
| RF Remote Control Distance | Open area greater than 25 meters (approx. 100FT) |
| Material | Plastic |
| Certification | RoHS, CE, CCC |
| Is Smart Device | No |
8. Warranty and Support
This QIACHIP product comes with a 1-year warranty from the date of purchase.
For further assistance or detailed documentation, you may refer to the official user manual PDF available from the manufacturer. Please visit www.qiachip.com for more information.