Voktta Volt Detector Tester

Contents

DC Voltmeter Ammeter Wattmeter User Manual

Model: Volt Detector Tester

Brand: Voktta

1. Introduction

This manual provides instructions for the safe and efficient use of your Voktta DC Voltmeter Ammeter Wattmeter. This digital meter is designed to accurately measure DC voltage, current, and power in various electrical applications. Please read this manual thoroughly before installation and operation.

Two main versions of this meter are available:

  • DC 0-50V, 5A, 250W Model
  • DC 0-100V, 10A, 999W Model (Note: Actual power display for 10A model may vary, e.g., up to 480W as seen in some displays, but rated up to 999W)

For a detailed PDF version of this manual, please refer to the official product documentation available at User Manual (PDF).

2. Safety Precautions

  • Ensure the power supply voltage is within the specified range (DC 7-12V).
  • Do not exceed the maximum voltage and current ratings of the specific meter model.
  • Always disconnect power before making or changing any connections.
  • Avoid contact with live circuits.
  • Do not operate the device in wet or damp conditions.
  • Do not attempt to disassemble or modify the meter, as this will void any potential support.

3. Setup and Installation

3.1 Physical Installation

The meter is designed for panel mounting. Ensure you have adequate space and create a cutout according to the dimensions provided in the Specifications section.

3.2 Wiring Instructions

Carefully follow the wiring diagram below. Incorrect wiring can damage the device or the connected circuit. Ensure all connections are secure before applying power.

Wiring diagram for DC Voltmeter Ammeter Wattmeter

Figure 1: Wiring Diagram

This diagram shows the connections for the power supply (DC 7-12V) to the meter, and the connections for the load to be measured. The meter measures voltage across the load and current in series with the load.

  • Power Supply (DC 7-12V): Connect the external DC power supply to the designated terminals. This powers the meter itself.
  • +Power-: These terminals are for the voltage measurement input. Connect them in parallel across the circuit or load you wish to measure.
  • +Load-: These terminals are for the current measurement input. Connect them in series with the load. Ensure the current flows through the meter correctly.

4. Operating Instructions

4.1 Display Overview

The meter features an HTN LCD display with 3 lines and 3 digits, simultaneously showing:

  • Voltage (V): Top line
  • Current (A): Middle line
  • Power (W): Bottom line

4.2 Measurement

Once correctly wired and powered on, the meter will automatically display the real-time voltage, current, and calculated power of the connected circuit. Ensure the measured values are within the meter's specified ranges.

4.3 Calibration (V_CAL / A_CAL)

The meter includes adjustment points for voltage calibration (V_CAL) and current calibration (A_CAL). These are typically small potentiometers or buttons on the device. If precise calibration is required, use a known accurate reference meter and adjust these points carefully. Refer to the product images for the location of these calibration points.

5. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the display and casing. Do not use abrasive cleaners or solvents.
  • Storage: Store the meter in a dry place, away from direct sunlight and extreme temperatures.
  • Service: This device contains no user-serviceable parts. Do not attempt to open or repair the unit.

6. Troubleshooting

  • No Display:
    • Check if the power supply (DC 7-12V) is correctly connected and providing power.
    • Ensure the power supply polarity is correct.
  • Incorrect Readings:
    • Verify all wiring connections are secure and correct according to the diagram.
    • Ensure the measured voltage and current are within the meter's specified operating range.
    • If readings are consistently off, consider performing a calibration using the V_CAL and A_CAL adjustments.
  • Fluctuating Readings:
    • Check for loose connections.
    • Ensure the power supply to the meter is stable.

7. Specifications

Dimensional drawing of the DC Voltmeter Ammeter Wattmeter

Figure 2: Product Dimensions

Overall dimensions and panel cutout size for installation.

FeatureSpecification
Brand NameVoktta
Model NumberVolt Detector Tester
Display TypeDigital Only (HTN LCD, 3 Rows, 3 Digits)
DIY SuppliesElectrical
CertificationCE
OriginMainland China
Power SupplyDC 7-12V
Working Current<15mA
Working Temperature-10°C to 60°C
Voltage Measurement RangeDC 0-50V (5A model) / DC 0-100V (10A model)
Current Measurement Range0-5A (5A model) / 0-10A (10A model)
Power Measurement Range0-250W (5A model) / 0-999W (10A model)
Voltage Error Range±1% (Adjustable)
Current Error Range±1% (Adjustable)
Power Error Range±1% (Adjustable)
Refresh Rate300ms/Time
Dimensions (Overall)79.5mm (L) x 43mm (W) x 13mm (D)
Panel Cutout Size71mm (L) x 28mm (W)

8. User Tips

  • Always double-check your wiring before applying power to prevent damage to the meter or your circuit.
  • For critical measurements, compare the meter's readings with a calibrated multimeter to ensure accuracy.
  • When measuring high currents, ensure your wiring is appropriately gauged to handle the current without excessive voltage drop or heating.

No specific user tips were available from buyer reviews or Q&A for this product.

9. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the seller or the manufacturer directly. Keep your purchase records for reference.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.