SCULPFUN Spot Welding Pen

Contents

SCULPFUN Spot Welding Pen Instruction Manual

Model: Integrated Type Spot Welding Pen

1. Introduction

This document provides instructions for the safe and efficient use of your SCULPFUN Integrated Type Spot Welding Pen. This high-quality spot welding pen is designed for efficient and reliable welding, particularly suitable for lithium battery packs. It features a robust design with thick copper bars for enhanced conductivity and an integrated structure for effective heat radiation.

The pen is equipped with dual springs on the handle, allowing each welding pin to expand and contract independently for precise contact. A built-in limit switch enables convenient one-hand operation, eliminating the need for a foot pedal.

2. Safety Instructions

WARNING: Please read all safety instructions carefully before use to prevent injury or damage to the device.

  • Power Source: Always connect the spot welding pen to a stable 12V external power source as specified. Using an incorrect voltage or an unstable power supply can damage the device and pose a safety risk.
  • Electrical Safety: Ensure all electrical connections are secure and free from damage. Do not operate the device with wet hands or in damp environments.
  • Heat: The welding tips and surrounding components can become very hot during operation. Avoid direct contact with hot parts to prevent burns. Allow the device to cool down before handling or storing.
  • Eye Protection: Always wear appropriate eye protection (e.g., safety glasses or goggles) when operating the spot welding pen to protect against sparks and molten material.
  • Ventilation: Use the device in a well-ventilated area to dissipate any fumes or heat generated during welding.
  • Flammable Materials: Keep the welding area clear of flammable materials, liquids, and gases.
  • Children and Pets: Keep the device out of reach of children and pets.
  • Modifications: Do not attempt to disassemble, modify, or repair the device yourself. Unauthorized modifications can lead to malfunction, electric shock, or fire, and will void any potential warranty.
  • Storage: Store the device in a dry, clean, and safe place when not in use.

3. Package Contents

Please check the package for the following items:

  • 1 x Spot Welding Pen

Note: External 12V power source is not included and must be provided separately.

4. Setup

  1. Unpacking: Carefully remove the spot welding pen from its packaging.
  2. Inspection: Inspect the device for any visible damage. If any damage is found, do not use the device and contact the seller.
  3. Power Connection: Connect the spot welding pen to a suitable 12V external power source. Ensure the connection is firm and secure.
Spot Welding Pen with components and in hand

Figure 1: Spot Welding Pen showing components and in use.

5. Operating Instructions

  1. Power On: Once connected to the 12V power source, the device is ready for operation.
  2. Grip: Hold the spot welding pen comfortably in one hand. The design provides comfortable hand feelings for extended use.
  3. Positioning: Position the welding pins onto the materials to be welded (e.g., lithium battery tabs). Ensure good contact between the pins and the workpiece.
  4. Welding: The built-in limit switch allows for one-hand operation. Apply slight pressure to the pen to trigger the weld. The dual springs ensure independent movement of each pin for consistent contact.
  5. Automatic Trigger: The pen features an automatic trigger mechanism, eliminating the need for a separate foot pedal.
  6. Post-Weld: After each weld, lift the pen from the workpiece.
Black Spot Welding Pen with accessories

Figure 2: Black Spot Welding Pen with included accessories (hex key, springs, switches).

Blue Spot Welding Pen with accessories

Figure 3: Blue Spot Welding Pen with included accessories.

6. Maintenance

  • Cleaning: Keep the welding pins clean and free from debris or oxidation. Use a fine abrasive or wire brush if necessary to ensure good electrical contact.
  • Storage: Store the spot welding pen in a dry, dust-free environment when not in use.
  • Cable Inspection: Periodically check the power cable for any signs of wear, cuts, or damage. Replace if necessary.
  • Springs: Ensure the dual springs operate smoothly and provide adequate tension for the welding pins.

7. Troubleshooting

  • No Weld/Weak Weld:
    • Ensure the 12V external power source is properly connected and functioning.
    • Check that the welding pins are clean and making good contact with the workpiece.
    • Verify the workpiece materials are suitable for spot welding.
  • Overheating:
    • If the device feels excessively hot, disconnect it from the power source and allow it to cool down.
    • Ensure the device is used within its intended duty cycle and not continuously for prolonged periods without rest.
  • Device Malfunction: If the device exhibits unusual behavior, makes strange noises, or emits smoke/smell, immediately disconnect it from the power source and cease use. Contact the seller for assistance.

8. Specifications

FeatureDetail
Product NameSpot Welding Pen
BrandSCULPFUN
Power Requirement12V External Power Source (not included)
Welding Needle Size50 x 3 x 3 mm (1.97 x 0.12 x 0.12 in)
Item Dimensions155 x 45 x 25 mm (6.10 x 1.77 x 0.98 in)
Item Weight250 g (8.82 oz)
Package Dimensions200 x 100 x 50 mm (7.87 x 3.94 x 1.97 in)
Package Weight300 g (10.58 oz)
MaterialThick Copper Bar (for conductivity)
OperationOne-hand operation, built-in limit switch, automatic trigger
ApplicationLithium battery pack spot welding
OriginMainland China

9. User Tips

Based on general user feedback for similar products, ensuring a clean contact surface on both the welding pins and the battery tabs is crucial for strong, consistent welds. Experiment with pressure and power settings (if your 12V power source is adjustable) on scrap material before working on your final project.

10. Warranty and Support

For technical support, warranty claims, or product inquiries, please contact the seller or the manufacturer directly. Keep your purchase records for any warranty-related services.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.