GRN-FLASHING RGB LED Extension Cable

Contents

RGB LED Extension Cable User Manual

Model: RGB LED Extension Cable

Brand: GRN-FLASHING

1. Product Overview

The GRN-FLASHING RGB LED Extension Cable is designed to extend the reach of your RGB or ARGB LED strips, allowing for flexible placement and connection. It is compatible with various LED strip types including 5050, 3528, 2835, and 3014, and comes in both 3-pin and 4-pin configurations.

Black 1-meter RGB LED extension cable with 3-pin and 4-pin connector types indicated.

Figure 1: GRN-FLASHING RGB LED Extension Cable (Black, 1 Meter)

2. Safety & Warnings

Important Safety Information

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture.
  • Handle with care to avoid cuts or injuries.

3. Setup Instructions

3.1. Preparation

  • Ensure your LED strips and controller are powered off before making any connections.
  • Verify that the voltage requirements of your LED strips match the output of your controller and the specifications of this extension cable (0-24V).
  • Identify the correct connector type (3-pin for ARGB, 4-pin for RGB) for your LED strips.

3.2. Connecting the Cable

  1. Align the pins of the extension cable with the corresponding pins on your LED strip or controller.
  2. Pay attention to polarity signs such as small arrows, "+" and "-" for one-to-one connection. Ensure the arrows on the connectors are aligned.
  3. Gently push the connectors together until they are firmly seated. The connection should be snug to ensure proper electrical contact.
  4. If extending between two LED strips, connect one end of the extension cable to the output of the first strip and the other end to the input of the second strip.
Image showing the male and female ends of the extension cable with alignment arrows for proper connection.

Figure 2: Proper alignment of extension cable connectors using arrows.

Diagram illustrating how to connect the extension cable between two LED strips.

Figure 3: Connecting the extension cable between LED strips.

Example setup showing LED strips connected via the extension cable to a controller.

Figure 4: Example of an LED strip setup using the extension cable.

4. Operating Instructions

Once the extension cable is securely connected between your LED strips and controller, you can power on your system. The cable facilitates the seamless transmission of power and data, allowing your LED strips to function as intended, extending their reach without loss of signal or brightness.

5. Maintenance

  • Keep the cable clean and free from dust. Use a soft, dry cloth for cleaning.
  • Avoid sharp bends or excessive pulling on the cable, as this can damage the internal wires or connectors.
  • Ensure the cable is not pinched or exposed to extreme temperatures.
  • Store the cable in a dry place when not in use.

6. Troubleshooting

  • LEDs not lighting up:
    • Check all connections for proper seating and ensure they are fully inserted.
    • Verify that the voltage of your LED strips matches the power supply and that the extension cable is within its working voltage range (0-24V).
    • Ensure the power supply is active.
  • Incorrect colors or flickering:
    • Re-check pin alignment and polarity (arrows, "+", "-" signs) on all connectors. Incorrect alignment can cause color issues.
    • Ensure the pins are not bent or damaged.
  • Intermittent connection:
    • Inspect the cable for any visible damage, cuts, or fraying.
    • Ensure connectors are clean and free from debris.
    • Verify that the pins inside the connectors are not loose or corroded.

7. Specifications

FeatureSpecification
Product NameDC connector (Extension Cable)
MaterialPlastic + Copper
Working Voltage0-24V
Maximum Current2-4A
Working Environment-40°C to +90°C
Length1 Meter
WeightApproximately 20g
Connector Types3-pin (ARGB) / 4-pin (RGB)
Compatibility5050, 3528, 2835, 3014 RGB/ARGB LED Strips
CertificationCE, RoHS
EU LVD VoltageBelow 50Vac or 75Vdc
High-Concerned ChemicalNone
Close-up view of the cable's construction, highlighting the copper wire core and silicone rubber coating for durability and conductivity.

Figure 5: High-quality copper wire core and silicone rubber coating.

8. User Tips

  • Pin Alignment: Always double-check the pin alignment and polarity (arrows, +,- signs) to ensure correct color display and prevent damage.
  • Cable Cleaning: If you notice any white residue or dust on the cables, clean them thoroughly before installation for optimal performance and aesthetics.
  • Length Planning: Measure your required extension length carefully to ensure the 1-meter cable meets your specific PC build or LED strip setup needs.
  • Flexibility: While the cable is designed to be flexible, avoid extreme bends to maintain its integrity and conductivity.

9. Warranty & Support

This product complies with CE and RoHS directives, ensuring it meets European safety, health, and environmental protection requirements.

For technical support or warranty inquiries, please contact the manufacturer directly using the information below:

Manufacturer Information:

Name: Shenzhen Lvseshuxing technology Co., LTD
Address: 708, Floor 7, Unit 2, Building B, Xinglongfu Chuangke Park, Yousong Road, Yousong Community, Longhua Street, Longhua District, Shenzhen
Zip Code: 518110
Contact Person: YiQi Wen
Tel: 18820779209
E-mail: 52680771@qq.com

EU Authorized Representative:

Name: GAVIMOSA CONSULTORIA, SOCIEDAD LIMITADA
Address: CASTELLANA 9144, 28046 Madrid
Contact Person: Jorge Wilson
Tel: +34 696313170
E-mail: compliance.gavimosa@outlook.com

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.