SAMOLLA Carp Fishing Reel

Contents

SAMOLLA Carp Fishing Reel User Manual

Model: Carp Fishing Reel Series (TOR4000 - TOR12000)

Brand: SAMOLLA

1. Introduction

This manual provides detailed instructions for the proper setup, operation, maintenance, and troubleshooting of your new SAMOLLA Carp Fishing Reel. Please read this manual thoroughly before using the product to ensure optimal performance and longevity.

SAMOLLA Carp Fishing Reel
Figure 1: SAMOLLA Carp Fishing Reel (Example Model)

2. Setup

2.1 Attaching the Reel to a Fishing Rod

  1. Ensure your fishing rod's reel seat is clean and free of debris.
  2. Place the reel foot into the reel seat's fixed hood.
  3. Tighten the reel seat's locking nut securely until the reel is firmly attached and does not wobble. Do not overtighten.

2.2 Spooling Fishing Line

  1. Open the bail arm.
  2. Thread the fishing line through the rod guides, starting from the tip down to the reel.
  3. Tie the line to the reel spool using an arbor knot or similar secure knot.
  4. Close the bail arm.
  5. Begin winding the line onto the spool, maintaining light tension on the line to ensure even and tight winding. Fill the spool to about 1/8 inch from the rim.

2.3 Handle Installation

The reel features an interchangeable right or left-hand CNC machined aluminum handle.

  1. Insert the handle shaft into the desired side of the reel body.
  2. Screw the handle cap or locking nut firmly to secure the handle.
Reel with large handle
Figure 2: Reel with large handle for comfortable use.

3. Operating Instructions

3.1 Double Brake System

This reel is equipped with a Front and Rear Dual Brake System for enhanced control during fishing.

  • Rear Brake (Baitfeeder Function): When casting bait into the water, engage the back release switch. Only the back release force works, allowing the fish to drag the bait a long distance without immediate resistance. This helps relax the fish's vigilance.
  • Front Brake (Fighting Drag): When a fish is hooked, shake the rocker arm. The front brake will engage, providing powerful stopping power for fighting larger fish.
Double Brake System Diagram
Figure 3: Diagram illustrating the Double Brake System operation.

3.2 Drag Adjustment

The reel features a superior drag system with triple disc advanced woolen drag washers, offering incredible stopping power up to 27kg. Adjust the drag using the oversized knob on the front of the spool for the main drag, and the knob at the rear for the baitfeeder function.

  • Turn the drag knob clockwise to increase drag tension.
  • Turn the drag knob counter-clockwise to decrease drag tension.
  • The oversized knob allows for micro click drag setting adjustments.
Reel features diagram including oversized knob
Figure 4: Key features including the oversized knob for drag adjustment.

3.3 Bail Arm Operation

The bail arm is used to control the release and retrieval of fishing line. To cast, manually open the bail arm. After casting, close the bail arm either manually or by turning the handle to engage the retrieve mechanism.

4. Maintenance

Regular maintenance is crucial for the longevity and optimal performance of your fishing reel. Always perform maintenance in a clean, well-lit, dust-free workspace.

4.1 Tools Required

Soft cloth, cotton swabs, bearing oil, gear grease, cleaning agent, screwdriver, tweezers.

4.2 Daily Basic Maintenance (After Each Use)

  1. Rinse the reel with clean fresh water to remove salt, sand, and dirt.
  2. Wipe the entire reel dry with a soft cloth.
  3. Remove the spool and air-dry the rotor and internal parts.
  4. Check the line roller, handle, and bail for smooth operation.
  5. Apply 1-2 drops of bearing oil to the line roller if it feels stiff or noisy.

4.3 Full Deep Maintenance (Every 1-3 Months)

Step 1: Disassembly

  1. Unscrew the spool knob and remove the spool.
  2. Take off the handle, lock nut, and star drag / drag knob.
  3. Remove the rotor and side cover screws.
  4. Carefully take out the gear set, bearings, and washers.
Internal Dismantling of Fishing Reel
Figure 5: Exploded view of the reel for internal dismantling.

Step 2: Cleaning

  1. Wipe old grease, dirt, and metal powder with a cloth and cotton swabs.
  2. Clean bearings with a cleaning agent and let them dry completely.
  3. Do not use strong solvents (e.g., gasoline, thinner) as they can damage components.

Step 3: Lubrication

  1. Gears & Main Shaft: Apply proper gear grease.
  2. Bearings & Line Roller: Apply 1-2 drops of bearing oil.
  3. Drag Washers: Lightly coat with special drag grease if needed.
  4. Do NOT overlubricate - excess oil attracts dust and debris.
Internal Gear Upgrade Comparison
Figure 6: Comparison of new corrosion-resistant internal gear (brass bearing) vs. old ordinary bearing (aluminum alloy).

Step 4: Reassembly & Adjustment

  1. Reinstall all parts in reverse order of disassembly.
  2. Tighten screws moderately; do not over-tighten.
  3. Adjust the drag system to ensure even tension.
  4. Test rotation, handle, and bail action to ensure smooth operation.

4.4 Maintenance Frequency

  • Occasional freshwater use: Every 2-3 months.
  • Frequent fishing: Every 1 month.
  • Saltwater / beach fishing: Clean after every use, full maintenance monthly.

5. Troubleshooting

Issue: Bail arm is bent or not closing properly.
Solution: Carefully inspect the bail arm for any visible bends or damage. If slightly bent, it may be possible to gently reshape it. If severely damaged, replacement may be necessary. Ensure no debris is obstructing its movement.
Issue: Spool makes a chirping noise or rubs against the reel body.
Solution: This can indicate the spool is sitting too low. Check if an additional washer is needed under the spool to raise its position slightly. Ensure all parts are correctly assembled and lubricated as per the maintenance section.
Issue: Line capacity seems lower than expected for the reel size.
Solution: Verify the line diameter (mm) and length (m) specifications for your specific reel model (e.g., TOR10000) against the line you are using. Different line types (monofilament, fluorocarbon, braid) and diameters will affect the actual capacity. Ensure the line is spooled evenly and tightly.

6. Specifications

General Features:

  • Material: Nylon (body), Aluminum (spool, handle)
  • Main Shaft: Hardened Stainless Steel
  • Drag System: Triple disc advanced woolen drag washers, Carbon Fiber and Metal Washers
  • Handle: Interchangeable right or left hand CNC machined aluminum handle
  • Frame: High strength graphite frame
  • Bearings: 12+1BB (Ball Bearings)
  • Fishing Reels Type: Distant Wheel
  • Fishing Method: Spinning
  • Baits Type: Powder
  • Origin: Mainland China
Stainless Steel Main Shaft and Drag System
Figure 7: Illustration of the Stainless Steel Main Shaft and Carbon Fiber/Metal Washer Drag System.

Model-Specific Parameters:

Table 1: SAMOLLA Carp Fishing Reel Model Specifications
Model Gear Ratio Ball Bearings Max Drag (kg) Weight (g) Line Capacity (mm/m)
TOR4000 5.2:1 12+1BB 10KG 362 0.30/110 0.35/90 0.40/80
TOR5000 5.2:1 12+1BB 10KG 367 0.35/100 0.40/85 0.45/75
TOR6000 4.9:1 12+1BB 17KG 460 0.35/140 0.40/125 0.50/100
TOR7000 4.9:1 12+1BB 17KG 464 0.40/135 0.45/120 0.50/105
TOR8000 4.1:1 12+1BB 27KG 770 0.20/500 0.24/420 0.26/330
TOR9000 4.1:1 12+1BB 27KG 765 0.34/470 0.40/300 0.50/200
TOR10000 4.1:1 12+1BB 27KG 755 0.40/500 0.48/420 0.57/280

Note: Information is for reference only and may have differences due to manual measurement.

Finsh Reel Parameter Table
Figure 8: Detailed specifications for various reel models.

Physical Dimensions:

Reel Dimensions for TOR4000/5000 and TOR6000/7000
Figure 9: Actual measurement and spool size for TOR4000/5000 and TOR6000/7000 series.
Reel Dimensions for TOR8000/9000/10000
Figure 10: Actual measurement and spool size for TOR8000/9000/10000 series.

7. User Tips

  • Initial Setup: Some users have noted that the bail arm might require slight adjustment or the spool might need an additional washer to prevent chirping. Inspect these components upon first use and adjust as necessary for smooth operation.
  • Saltwater Use: Always rinse your reel thoroughly with fresh water immediately after saltwater exposure to prevent corrosion and extend its lifespan.
  • Line Capacity: Pay close attention to the specified line capacities for each model. Using line that is too thick or spooling too much line can lead to tangles and reduced casting performance.

8. Warranty and Support

8.1 Warranty Information

This product comes with a 12-month manufacturer's limited warranty for defective items from the date of receipt. Accessories are covered by a 3-month warranty. The warranty does not cover items damaged due to misuse or improper handling after receipt.

Defective items must be reported and returned within the warranty period, preferably in their original packaging. Please provide your order number and a description of the defect when contacting support.

8.2 Additional Resources

For a more detailed user manual and additional guides, you may refer to the official PDF document: User Manual (PDF).

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.