KEBETEME Digital Engine Tach Hour Meter

Contents

Digital Engine Tach Hour Meter User Manual

Model: Digital Engine Tach Hour Meter | Brand: KEBETEME

1. Introduction

The KEBETEME Digital Engine Tach Hour Meter is a self-powered LCD device designed to measure engine RPM (revolutions per minute) and record total operating hours. It is suitable for all spark ignition gasoline engines. The unit features a large LCD display for easy reading, a wide operating temperature range, and a replaceable CR2450 battery.

Digital Engine Tach Hour Meter with motorcycle in background
The KEBETEME Digital Engine Tach Hour Meter, showing its display and a motorcycle in the background.
Diagram showing various applications for the tach hour meter: motorcycle, snowmobile, ATV, chainsaw, lawn mower, motorboat.
The tach hour meter is suitable for a wide range of gasoline engines, including motorcycles, snowmobiles, ATVs, chainsaws, lawn mowers, and motorboats.

2. Safety Information

WARNING: Failure to comply with the following safety requirements may result in electric shock, fire, product damage, personal injury or property loss.

  • RISK OF ELECTRIC SHOCK: Do not open the product housing; there are no user-serviceable parts inside. Unauthorized disassembly will cause electric shock risk and void the product warranty. All servicing, repair and part replacement must be performed by qualified and authorized technicians only.
  • POWER SUPPLY SAFETY: Use only the manufacturer-specified power supply/charger with the matching model. Damaged power cords/cables (cracks, fraying, exposed wires) must be replaced with original parts immediately; do not continue to use damaged power accessories.
  • OVERHEATING PREVENTION: Do not block the product's ventilation openings (if applicable); do not place the product on soft surfaces (beds, sofas, rugs) that obstruct airflow. Discontinue use immediately if the product feels abnormally hot, emits strange odors or smoke.
  • ABNORMAL USAGE HANDLING: If the product malfunctions (e.g., indicator light flickers abnormally, no response to operation, abnormal noise), unplug the power supply immediately and stop using it. Contact the authorized service center for inspection and repair; do not attempt to repair the product by yourself.
  • BATTERY SAFETY: For products with built-in/replaceable batteries, do not short-circuit, crush, puncture or incinerate the battery. Do not recharge non-rechargeable batteries; replace batteries with the same model/specification only (CR2450).
  • CHILD SAFETY: Keep the product and its small accessories (e.g., small buttons, batteries) out of reach of children under 3 years old to prevent choking, electric shock or other accidents.
  • CLEANING SAFETY: Disconnect the power supply before cleaning the product; use a dry, soft cloth to wipe the surface. Do not use water, alcohol, detergent or other chemical cleaners to clean the internal components.
  • EMERGENCY TREATMENT: In case of product fire, cut off the power supply immediately and use a dry powder fire extinguisher to put out the fire (do not use water). In case of electric shock caused by the product, cut off the power first and seek medical attention immediately.

3. Setup

3.1. Battery Installation

The unit is powered by a replaceable CR2450 battery. Ensure the battery is correctly inserted according to polarity markings. The battery is not included with some models.

Image showing the tach hour meter and its battery compartment, indicating a replaceable CR2450 battery.
The device uses a replaceable CR2450 battery. Ensure correct insertion.
Close-up of the CR2450 battery compartment.
Close-up view of the CR2450 battery compartment.

3.2. Physical Installation

Unpack the unit and attach it to a location where it can be easily read. Before changing any settings or installing, ensure the engine is off.

To connect the tachometer, wrap the provided wire around the spark plug wire of the engine for 3 to 5 rounds and fix it securely. The LCD will then display the accumulated hours.

Installation diagram showing how to wrap the wire around a spark plug for 5 rounds and a table for stroke mode selection.
Wrap the sensor wire around the spark plug wire for 3 to 5 turns to ensure proper signal detection.

3.3. Setting the Tachometer (Spark Plug Firing Revolution)

  1. Press and hold the S1 button for 4 seconds. The LCD will display '01' (spark plug fires twice per revolution) or '02' (once per revolution).
  2. Press and release the S1 button to increment to the desired number.
  3. Once you find your desired spark plug firing pattern, release the S1 button.
  4. The LCD will blink for 8 to 10 seconds and return to total hour meter mode. The default for the standard model is '02' (once per revolution).

Refer to the table below for stroke mode selection:

Stroke Mode Selection
ModeDescription
014 stroke in common
022 stroke in common
03Other stroke
04RPM shut down, only display hours

4. Operating Instructions

4.1. Display Modes

The device can display total accumulated hours (TOT Hours) when the engine is off, and real-time RPM when the engine is running.

Image showing two display modes: TOT Hours (0.0 hours) and RPM (1500 RPM).
The meter displays total hours when the engine is off and real-time RPM when the engine is running.
Diagram illustrating the speed system with a display of 1500 RPM and specifications: Speed range 0-20000RPM, Speed accuracy 10RPM.
The speed system provides real-time RPM display with a range of 0-20000 RPM and an accuracy of 10 RPM.

4.2. Backlight Modes

The device offers three backlight modes: Automatic, Always On, and Off.

Diagram showing screen off mode (5-Aut) and screen on mode (5-On).
Choose between automatic screen off (5-Aut) or always on (5-On) to manage power consumption.
Diagram showing three backlight modes: L-Off (backlight off), L-Aut (automatic backlight off after 5 minutes), L-On (backlight always on).
Detailed view of backlight modes: L-Off, L-Aut (automatic), and L-On (always on).
  • L-Off: Backlight is turned off.
  • L-Aut (5-Aut): The LCD screen displays for 5 minutes, then the screen is turned off to save electricity. Press any button to turn the screen on again.
  • L-On (5-On): The LCD screen is always on.

4.3. To Display Hours Only

  1. Press and hold the S1 button until '04' is displayed.
  2. Release the S1 button and the display returns to total hours after 8 to 10 seconds.
  3. When the engine is running, the display will show hours only, no RPM, and the hour icon will blink.

5. Maintenance

5.1. Setting the Maintenance Interval Timer

The device can be programmed to remind you of regular engine maintenance, such as air filter replacement.

Maintenance reminder feature showing '80.0 HOURS SERVICE' and text 'When the maintenance interval time is reached, and the LCD display will flashing'.
The maintenance reminder feature tracks countdown time for maintenance tasks. When the set time is reached, "SERVICE" will flash.
Timing System diagram showing 'position in readiness' with 0.0 hours and 'Engine operating status' with 1500 RPM, highlighting maintenance reminder and settable maintenance time.
The timing system allows setting maintenance reminders from 0000.0 to 9999.9 hours. The default is 0000.0 hours.
  1. Press and hold the S2 button for 4 seconds. The rightmost digit on the LCD will flash and the "SERVICE" icon will be displayed.
  2. Pressing and releasing the S1 button causes the flashing digit to automatically increment.
  3. When the desired number for the digit is reached, press and release the S1 button and then press the S2 button for 1 second to increment to the next digit.
  4. Repeat until the desired service time has been entered. After 14-16 seconds with no buttons pressed, the LCD will return to total hours mode. The maintenance time will automatically default to the number previously programmed.

5.2. Activating the Maintenance Interval Timer

Press and hold the S1 and S2 buttons simultaneously for 4 seconds. The two digits will increment to '09' seconds and then return to total hours mode. When the engine is running and the maintenance time has reached zero, the "SERVICE" icon will come on.

5.3. Viewing Maintenance Interval

  1. Press and hold the S2 button for 4 seconds to view the remaining time or your maintenance interval.
  2. To continue current maintenance, do nothing.
  3. If you would like to start a new maintenance interval, repeat steps 5.1.1 to 5.1.4 again.
  4. Each time you want to view the remaining time of your maintenance process, press and hold S2.

5.4. Resetting the Service Icon

Press and hold the S1 and S2 buttons for 20 seconds. The service icon will shut off.

5.5. Resetting Total Hours and Maintenance Time

Press and hold the S1 button until '05' is displayed. Release the S1 button and after 8 to 10 seconds, press and hold the S1 and S2 buttons simultaneously for 20 seconds. The meter will perform a total reset.

6. Troubleshooting

6.1. General Issues

  • No Display/Incorrect Readings:
    • Ensure the spark plug wire is wrapped correctly (3 to 5 rounds) and securely fixed.
    • Check if the battery (CR2450) is installed correctly and has sufficient charge.
    • Verify the correct stroke mode (01, 02, 03) is selected for your engine type.
  • Abnormal Product Behavior: If the product malfunctions (e.g., indicator light flickers abnormally, no response to operation, abnormal noise), discontinue use immediately. Do not attempt to repair it yourself. Refer to the Warranty/Support section for contact information.

7. Specifications

FeatureSpecification
Model NameDigital Engine Tach Hour Meter
Brand NameKEBETEME
MaterialABS
Resolution0.1 Hours / 10 RPMs
Reading (Max)9999.9 Hours / 99999 RPMs
Accuracy1 minute or 10 RPM (Quartz)
Operating Temperature-30°C to 85°C
Cable LengthApprox. 170 cm (66.9 inches)
Power Supply1x CR2450 battery (replaceable)
Product Size5 x 4.5 x 2 cm (1.97 x 1.8 x 0.8 inches)
LCD Size42 x 12 mm (1.65 x 0.47 inches)
Waterproof RatingIP65
Diagram showing the dimensions of the tach hour meter: 73.5mm width and 46.7mm height.
Dimensions of the Digital Engine Tach Hour Meter.
Image highlighting the IP65 waterproof rating of the tach hour meter.
The device features an IP65 waterproof rating.

8. Warranty and Support

8.1. Warranty Information

Most products come with a 1-year warranty from the store. Please retain your purchase records for warranty claims.

8.2. Manufacturer Information

Manufacturer: Shenzhen Meiteai E-commerce Co., Ltd

Address: CN-Building A, Building 201A, No. 8-14 Jinyuan Road, He'ao Community, Yuanshan Street, Longgang District, Shenzhen, 518000

Email: qiujianqiang@youyuepin.cn

Telephone: 86-13714205204

8.3. After-Sales Service

If you encounter any problems during use that cannot be solved by the troubleshooting guide, please contact our online after-sales service team. We will provide you with professional technical support and solutions.

Contact Email: successservice2@hotmail.com

Contact Telephone: +34-910602659

9. User Tips

  • This tach hour meter is versatile and can be adapted for various applications beyond standard engines, such as drill presses, by utilizing alternative signal sources like Hall sensors.
  • The device is designed with a replaceable CR2450 battery, ensuring long-term usability.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.