1. Product Overview
This product is a replacement rear bumper brake light assembly with an integrated reflector, designed specifically for the Hyundai IX35 models from 2010 to 2015. The unit combines a stop lamp (brake light) and a red reflector to enhance vehicle visibility during braking and at night. It is typically located on the lower section of the rear bumper.
The assembly includes the light housing, lens, and bulb socket. A bulb may be included depending on the specific product listing.
- OEM Part Numbers: 92405-2Z300 (Right Side), 92406-2Z300 (Left Side)
- Type: Brake light with integrated reflector
- Placement: Rear bumper (driver or passenger side, verify based on your vehicle's layout)
- Bulb Type: Compatible with standard 12V automotive bulbs (e.g., 1156, W16W). Always check your original bulb type for confirmation.

Figure 1: Front view of the rear bumper brake light reflector pair.

Figure 2: Rear view of a single unit, illustrating the bulb socket and wiring connector.
2. Setup: Installation Instructions
Note: Installation requires basic mechanical knowledge and proper tools. If you are not experienced with automotive electrical systems, it is highly recommended to consult a professional mechanic.
- Preparation: Ensure the vehicle is parked on a level surface, the ignition is off, and the keys are removed. To prevent electrical shorts, disconnect the negative battery terminal.
- Access the Bumper Area: The rear bumper brake light is typically accessible from behind the bumper or through the trunk area. You may need to remove specific trim panels or reach underneath the vehicle to gain access.
- Disconnect Electrical Connector: Locate the wiring harness connected to the old light assembly. Press the release tab on the connector and pull it apart to unplug it.
- Remove Old Light Assembly: The existing light is usually held in place by screws, bolts, or clips. Carefully remove these fasteners and gently pull the assembly away from the bumper. If it feels stuck, check for any additional hidden clips or adhesive.
- Transfer Bulb (if necessary): If your new assembly does not include a bulb, carefully remove the bulb from the old unit. This is typically done by twisting the socket counterclockwise and then pulling the bulb out. Insert the bulb into the new socket and twist clockwise to secure it.
- Install New Light Assembly: Align the new light with the opening in the bumper. Push it into place until it seats properly and flush with the bumper surface. Secure it using the original screws or clips. Do not overtighten the fasteners.
- Reconnect Electrical Connector: Plug the vehicle's wiring harness into the new light's socket until you hear or feel a secure click.
- Test Function: Reconnect the negative battery terminal. Turn on your vehicle's ignition and test the brake light by pressing the brake pedal. Verify that the light illuminates brightly and that the reflector is properly positioned and visible.
- Reassemble Trim: If any trim panels were removed during the access step, carefully reinstall them, ensuring all clips and fasteners are secure.

Figure 3: Example of the brake light reflectors installed on a Hyundai IX35.
3. Operating
Once installed, the rear bumper brake light reflector operates automatically as part of your vehicle's lighting system. The brake light illuminates when the brake pedal is pressed, signaling to other drivers that your vehicle is slowing down or stopping. The integrated reflector passively enhances visibility by reflecting light from other vehicles, particularly at night or in low-light conditions, even when the brake light is not active.
4. Maintenance and Care
- Inspection: Periodically inspect the light lens for any signs of cracks, moisture ingress, or other damage. Replace the assembly immediately if damage is found to maintain optimal visibility and compliance with safety regulations.
- Cleaning: Clean the lens gently using a soft, damp cloth. Avoid using abrasive cleaners, harsh chemicals, or directing high-pressure water jets directly onto the light, as this can damage the lens or seals.
- Bulb Check: Check the bulb periodically. If the brake light fails to illuminate, replace the bulb first before assuming the entire assembly is faulty.
- Seal Integrity: Ensure the rubber gasket or seal around the light assembly remains intact. A compromised seal can allow water entry, leading to electrical failure or condensation inside the lens.
- Vehicle Washing: When washing your vehicle, avoid directing high-pressure water streams directly at the edges of the light assembly to prevent dislodging or damaging the seals.
5. Troubleshooting
- Light Not Illuminating:
- Check the bulb: Ensure it is correctly seated and not burnt out. Replace if necessary.
- Check electrical connection: Verify the wiring harness is securely plugged into the light assembly.
- Check vehicle fuse: Consult your vehicle's owner manual for the location of the brake light fuse and check if it's blown.
- Moisture or Condensation Inside Lens:
- Inspect the rubber gasket/seal around the light assembly for damage or improper seating. Re-seat or replace the seal if compromised.
- Ensure all mounting screws are tightened appropriately to create a proper seal.
- Light Appears Loose:
- Check all mounting screws, bolts, or clips. Tighten any loose fasteners.
- Ensure the light assembly is correctly seated in the bumper opening.
6. Specifications
| Item Type | Rear Bumper Lights Assembly |
| OEM NO. | 924052Z300, 924062Z300 |
| Origin | Mainland China |
| Compatible Vehicles | Hyundai IX35 (2010, 2011, 2012, 2013, 2014, 2015) |
| Bulb Type Compatibility | Standard 12V automotive bulbs (e.g., 1156, W16W) |
| Package Length | 25 cm |
| Package Width | 15 cm |
| Package Height | 10 cm |
| Package Weight | 0.24 kg |
7. Usage Restrictions and Safety Information
7.1. Usage Restrictions
- This product is specifically designed for Hyundai IX35 models from 2010 to 2015. It may not fit other vehicles without modification.
- The light is intended for use as a rear brake light and reflector only. Do not use for other purposes.
- Ensure the product complies with local road safety regulations before installation. Functioning brake lights and reflectors are mandatory in most regions.
- If your vehicle has LED or CAN-BUS electrical systems, verify compatibility to prevent error codes or hyper-flash. Load resistors may be required in some cases.
- This assembly may be sold as a single unit (left or right); ensure you purchase the correct side for your vehicle.
7.2. Safety Information
- Always disconnect the vehicle's 12V battery before working on electrical components to avoid short circuits, electric shock, or accidental airbag deployment.
- Use appropriate tools and wear protective gloves to prevent injury when working near the bumper area.
- Ensure the light is properly secured after installation; a loose light could fall out while driving, posing a hazard to other road users.
- After installation, verify that the brake light functions correctly and is clearly visible from the rear. Malfunctioning brake lights can lead to rear-end collisions.
- If you encounter significant resistance during disassembly or assembly, stop and consult a professional to avoid breaking bumper clips or trim.
- Do not modify the light housing or wiring; this may cause electrical issues or non-compliance with safety regulations.
8. User Tips
- Bumper Removal: Be aware that installation may require the removal of the rear bumper for easier access.
- Socket Fit: If the lamp socket from your original wiring doesn't fit perfectly into the new assembly, slight adjustments to the socket's slots might be needed for a secure fit.
- Existing Wiring: Before starting, check if your vehicle already has the necessary wiring for this part, especially if you are adding it to a model that didn't originally come with this specific light.
- Quantity Check: Confirm whether your purchase includes a single unit (left or right) or a pair, to ensure you have the correct parts for your needs.
- Appearance: Many users report that the product looks original and fits well, enhancing the vehicle's rear appearance.
9. Warranty and Support
This product is an aftermarket replacement part designed to meet or exceed OEM specifications. For further assistance, warranty information, or any product-related inquiries, please contact your seller or refer to the original product listing on the platform where you made your purchase.
For a complete version of the user manual, including any additional diagrams or detailed instructions, please refer to the PDF document available at: User Manual (PDF).