ToolkitRC M7AC

Contents

ToolkitRC M7AC Intelligent Charger User Manual

Model: M7AC | Manual Version: V1.0 (2022.08)

1. Introduction

Thank you for purchasing the M7AC balance charger. Please read this manual carefully before use.

The M7AC is a multifunctional tool that integrates functions such as a balance charger and discharger, a signal measuring device, and a signal source.

Key Features:

  • Support AC100W or DC300W dual input.
  • Charges, discharges, and balances (where applicable) LiPo, LiHV, LiFe, Lion, LTO 1-6S, NiMh 1-16S, PB 1-10S batteries.
  • Charge current: MAX 15A @MAX300W.
  • Discharge current: Recycle / External mode Max 15A @300W. Internal mode Max 3A @15W.
  • Lithium battery cut-off voltage can be adjusted (TVC function).
  • Measures battery voltage, battery internal resistance, and balances lithium packs automatically.
  • Measures / outputs PWM/PPM/SBUS standard signals with an accuracy of 1 microsecond.
  • Constant current and constant voltage source output, customizable 1-28V constant voltage, 0.5-15A constant current.
  • Can be adapted for charging consumer-grade drone batteries.
  • Multi-language user interface and voice broadcast.
  • Easily upgradable via USB.

Further Information:

To ensure you have the best experience with this product, please visit www.toolkitrc.com for news, information, and firmware updates.

2. Safety Information

  • The M7AC allows input voltage of DC 7-28V or AC 100-240V. Ensure the charger is only connected to a suitable power source and correct polarity.
  • Do not use this product in hot, humid, flammable, or explosive environments.
  • Please do not use this charger without supervision. Never leave charging batteries unattended.
  • When not using this product, please unplug the input power.
  • When using the charging function, please set a current that matches the battery. Do not set an excessive current for charging to avoid damage to the battery. Check the guidelines of your battery's manufacturer for correct charging instructions.

⚠ WARNING: This product can expose you to chemicals including phthalates (DEHP), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

3. Setup

3.1 M7AC Layout

Familiarize yourself with the various ports and controls on your M7AC charger:

ToolkitRC M7AC Charger Front View with Display and Controls
Front view of the M7AC charger, showing the display, scroll wheel, and Exit button.
ToolkitRC M7AC Charger Side View with USB, Balance, and Output Ports
Side view of the M7AC, highlighting the USB output, balance port, signal port, and main output ports.
ToolkitRC M7AC Charger Back View with DC Input, AC Input, Cooling Fan, and AC Switch
Back view of the M7AC, showing the DC input, AC input, cooling fan, and AC switch.

3.2 Quick Start Guide

  1. Connect Power: Connect a 7-28V DC or AC 100-240V power supply or input battery to the input port on the back of the M7AC.
  2. Boot Up: The display will show the boot logo for 2 seconds, accompanied by a welcome sound (voice pack dependent).
  3. Main Interface: After booting, the screen enters the main interface, displaying current voltage, power, and cell information.
  4. Navigation:
    • Press and hold [Exit] to enter the auxiliary function interface.
    • Scroll the [Scroll Wheel] to switch between pages.
    • With the charger idle, short press [OK] to set charging parameters.
    • During charging, press [OK] to adjust amperage or stop the charge.
    • With the charger idle, press and hold [OK] to enter the system settings.
    • Short press [Exit] to return to the previous interface.

User Tip:

Always double-check your battery type and cell count settings before initiating a charge cycle to prevent damage to your batteries or the charger.

4. Operating Instructions

4.1 Charge and Discharge Settings

From the main interface, short press [OK] to enter the charging function. Open the battery selection option in system settings to configure your battery parameters.

4.1.1 Battery Type Setting

Scroll the [Scroll Wheel] to select a preset battery type or create a new one. Up to 32 battery files can be created. Press [Enter] to configure a specific battery setting.

The charger supports charging and discharging of 6 types of batteries: LiPo, LiHV, LiFe, Lion, LTO, NiMh, and PB. A smart battery mode is also available.

Battery Type Glossary:
  • LiPo: Lithium polymer battery, nominal voltage 3.70V, fully charged 4.20V.
  • LiHV: High-voltage lithium battery, nominal voltage 3.85V, fully charged 4.35V.
  • LiFe: Iron-lithium battery, nominal voltage 3.30V, fully charged 3.60V.
  • Lion: Lithium-ion battery, nominal voltage 3.60V, fully charged 4.10V.
  • LTO: Lithium-ion battery, nominal voltage 2.40V, fully charged 2.70V.
  • NiMh: Nickel-metal hydride battery, nominal voltage 1.20V.
  • PB: Lead-acid battery, nominal voltage 2.00V.

Warning: Ensure the correct battery type is selected. Incorrect selection can damage the battery or cause a fire hazard. Do not use this product to charge non-compatible battery chemistries.

4.1.2 Cell Setting

Move the cursor to [Battery Section] and press [OK] to modify the number of cells. Rotate the [Scroll Wheel] to adjust the value. When set to [Auto], the charger automatically identifies the number of cells by checking the total voltage against the balance port data. Short press [OK] and [Exit] to save.

Tip:

  • If the connected battery is over-discharged or over-charged, an incorrect cell-count may occur. Adjust manually if needed.
  • Incorrect cell count settings can lead to overcharging and fire risk.
  • Connecting the balance port allows for more accurate cell count determination.

4.1.3 Work Mode

Move the cursor to [Mode] and press [OK] to select the desired work mode:

  • Charge: For charging LiPo, LiHV, LiFe, Lion, LTO, NiMh, and PB batteries.
  • DisCHG (Discharge): For discharging LiPo, LiHV, LiFe, Lion, LTO, NiMh, and PB batteries.
  • StoCHG (Storage Charge): For storing LiPo, LiHV, LiFe, Lion, LTO batteries at optimal storage voltage.
  • Cycle: For cycling NiMh batteries.

4.1.4 Discharge Mode

When DisCHG, StoCHG, or Cycle modes are selected, the discharge mode option appears. Move the cursor to [Discharge Mode] and press [OK] to modify:

  • Inter (Internal): Discharges using internal heat dissipation, max 3.0A@15W.
  • Recycle: Recovers power to the input battery when another battery is used as input, max 15.0A@300W.
  • External: Discharges through an external load connected to the input port, max 15.0A@300W.

4.1.5 Max Input Voltage

When 'Recycle' discharge mode is selected, the [Max Input Vol.] option appears. Adjust this value to set the maximum input voltage. If the input voltage reaches this value during discharge, the process will stop.

Tip: Set the Max input voltage to the highest protection voltage of your power supply. High overvoltage settings can damage the input power source.

4.1.6 End Voltage Setting (TVC)

Move the cursor to [End Voltage] and press [OK] to modify the end voltage for individual cells. This is the charge cut-off voltage (range: +/- 50mV of full voltage) or discharge cut-off voltage. Adjust using the [Scroll Wheel] in 0.01V steps.

Note:

  • Only LiPo, LiHV, LiFe batteries can set the cut-off voltage.
  • Do not modify the cut-off voltage if unfamiliar with battery characteristics.
  • TVC stands for Terminal Voltage Control.

4.1.7 Current Setting

Move the cursor to [Charge Current] or [DisCHG Current] and press [OK] to modify the current. Rotate the [Scroll Wheel] to adjust the value in 0.1A steps. The charger supports up to 10.0A.

Tips:

  • Set the charging rate to 1-2C according to battery capacity (e.g., 2000mAh battery = 2.0-4.0A charge current).
  • Charge/discharge current is only valid in the corresponding work mode.

4.1.8 NiMH Setting (PeakV)

When the battery type is NiMH, you can set the peak voltage (PeakV) at which the battery is considered fully charged. The range is 5mV-15mV.

PeakV: The maximum voltage drop per cell when the nickel-metal hydride battery is fully charged. This function is only available for NiMH cells.

4.1.9 Cycle Setting

For NiMh batteries in Cycle mode, options for [Cycle time] (2-12 cycles) and [Rest time] (2-10 minutes) will appear. The charger follows a discharge->charge->discharge->charge pattern.

4.1.10 External Load Setting

If 'External' discharge mode is selected, set the wattage according to the external load used.

4.1.11 Smart Battery Setting

When 'UAV battery' is selected as the battery type, you can choose the drone model (e.g., Mavic2 17.6V, MavicS 13.05V, Phantom 17.4V, Inspire 26.1V) and set the Max current (0.5A to 15A).

4.2 Charge and Discharge Work

Once charging or discharging begins, the charger displays real-time information:

  • P1: Power selection in system settings
  • Input Voltage: Current input voltage.
  • Accumulated Power Consumption: Total power consumed.
  • Internal Temperature: Charger's internal temperature.
  • V: Constant voltage sign; C: Constant current sign.
  • Main Port Voltage: Voltage at the main output port.
  • Main Port Current: Current at the main output port.
  • Working Time: Duration of the current operation.
  • Charged Capacity: Total capacity charged/discharged.
  • Cell Voltage: Voltage for each individual battery cell.

Rotate the [Scroll Wheel] to toggle between different display pages, including internal resistance information and general charging status.

To dynamically adjust charge current or stop charging, short press [OK]. To end the process, move the cursor to [Stop] and press [OK]. A popup with an audible tone will indicate completion or an error.

Important Tips for Charging/Discharging:

  • Never leave cells unattended during operation.
  • For lithium batteries, balancing only occurs if the balance plug is connected. The charger will automatically balance each cell if detected.
  • If the initial battery is disconnected after being fully charged, charging will automatically start for the next battery. Ensure subsequent battery cell counts match the initial battery's setting.

4.3 Accessibility Functions

From the main interface, long press [Exit] to access auxiliary functions:

4.3.1 Measure Resistance

Short press [OK] to test the internal resistance of the connected battery. The result will be displayed on the main interface.

4.3.2 Measure Signal

Move the cursor to [Measure signal] and short press [OK]. Scroll the [Scroll Wheel] to select the signal type (PWM, PPM, SBUS).

  • PWM: Displays pulse width (e.g., 1500us) and frequency (e.g., 20.0ms/50Hz).
  • PPM: Displays pulse width for each channel (1-8).
  • SBUS: Displays pulse width for channels (1-16) and overall status (Channel DG1/DG2, Frame lost, Failsafe, Endbyte).

4.3.3 Signal Output

Move the cursor to [Signal Output] and short press [OK]. Scroll the [Scroll Wheel] to select the signal type (PWM, PPM, SBUS).

  • PWM: Set output mode to Manual, Auto 1, Auto 2, or Auto 3. In Manual mode, adjust pulse width (800-2200us) and cycle (2.5ms/400Hz to 50.0ms/20Hz). Auto modes change pulse width at different speeds.
  • PPM/SBUS: Move the cursor to the channel value and press [OK] to modify the output pulse width.

4.3.4 ESC Test

Select [ESC test] and short press [OK]. Scroll the [Scroll Wheel] to adjust pulse width/cycle to test your Electronic Speed Controller (ESC).

4.3.5 Power Supply Function

Select [Power] and short press [OK]. You can set the output voltage (1-28V) and current (0.5-15A). Move the cursor to [Start] and press [OK] to begin power output.

5. System Settings

From the main interface, long press [OK] to enter the system settings. Short press to expand each setting category.

5.1 Input Settings

  • Power selection: Preset power 1, power 2, power 3.
  • Power type: Choose between battery pack and adapter. Recycle mode is enabled for battery packs, disabled for adapters.
  • Max power: Maximum wattage allowed via the input port during charging.
  • Max current: Maximum current allowed via the input port during charging.
  • Voltage range: Input voltage range.

5.2 Security Settings

  • Safe inter Temp.: Charging stops if the device's internal temperature exceeds this value (default 70°C).
  • Safe Exter Temp.: Charging stops if the environment temperature exceeds this value (default 50°C).
  • Safe time: Maximum time limit for continuous charging/discharging operation (default 200Min).
  • Safe capacity: Maximum accumulated capacity for a charging/discharging session (default 20Ah).

5.3 Personalization

  • Backlight: Backlight brightness level (1-10).
  • Operation volume: Volume of the scroll wheel (Off, Low, Medium, High).
  • Announce volume: Menu readout volume (Off, Low, Medium, High).
  • Warning volume: Warning tone volume (Off, Low, Medium, High).
  • Language: System display language (English, Chinese, German, Portuguese, Korean, etc.).
  • Theme style: Light or Dark themes.

5.4 Other Settings

  • Battery selection: Option to show/hide frequently used parameters.
  • Work completed: Whether to stop or trickle charge after charge completion.
  • Balance start Vol.: Balance cells prior to full current charge.
  • Continuous work: Enables/disables continuous charging/discharging after battery replacement.
  • Default: Restore factory settings.
  • ID: Independent ID for each device (e.g., FF3005D3 - V1.00).

6. Customize Function

The M7AC supports customizable boot images and voice packs. Insert a TF card (128MB-16GB) into the TF card slot. Connect the USB-A cable to your computer. Two USB drives will appear: one for firmware upgrades (named Toolkit) and another for customized files. The root directory contains two folders: LOGO (for boot images) and SOUNDS (for voice files).

6.1 Boot Image

When the M7AC is turned on, it reads the file named logo.bmp from the LOGO folder. If successful, this image will be displayed as the startup page.

Tips:

  • Only supports BMP file format with a resolution of 240x320 pixels.
  • If the file cannot be read, the default startup page will be displayed.

6.2 Broadcast Voice

The M7AC reads voice files from the SOUNDS folder. Voice files are categorized by language in separate folders.

Language Folders:

NameDescriptionNameDescription
CHIChineseDEUGerman
ENGEnglishESPSpanish
FRAFrenchITAItalian
JAPJapaneseKORKorean
PORPortugueseTRATraditional

Voice File Descriptions:

File NameFile Description
0000.wav-0090.wavNumber 0-90 voice
0100-0109.wavNumber 100-1000 voice
0167-0176.wavNumbers .1-.9 Voice
Bootup.wavBootup sound
Warning.wavWarning sound
OtherMenu broadcast Voice

Tip: Only supports Wav file format, Mono file.

7. Other Functions

7.1 Firmware Upgrade

Connect the M7AC to your computer using the provided USB cable. Your computer will recognize a USB drive named 'Toolkit'. Download the upgrade file (app.upg) from the official ToolkitRC website and overwrite the files in the drive to upgrade the firmware.

7.2 USB Output

The Type-A USB port supports 5.0V 2.0A output to charge mobile devices.

7.3 Automatically Continue Charging/Discharging

When a battery is fully charged, you can connect the next battery. The device will automatically continue to charge and discharge. This function can be enabled/disabled in the settings menu.

7.4 Fan Level

  • If the internal temperature exceeds 45°C, the fan operates at half speed to reduce noise.
  • If the internal temperature exceeds 53°C, the fan operates at full speed for enhanced heat dissipation.

7.5 Manual Voltage Calibration

With the M7AC powered off, press and hold the [roller]. Without releasing the roller, connect the power supply. The system will enter manual voltage calibration mode. Use a voltmeter to measure the actual voltage of each battery. Move the cursor to the corresponding voltage value and modify it to match the voltmeter reading. After calibration, move the cursor to 'save', short press once, and the buzzer will beep once to confirm success. Exit or shut down after calibration.

7.6 Full Charge Mode

When a lithium battery is fully charged, the charger will prompt "Fast charge complete". If the battery is not removed, the charger will trickle charge until the battery is disconnected.

8. Maintenance

  • Keep the charger clean and free from dust and debris. Use a soft, dry cloth for cleaning.
  • Avoid exposing the charger to extreme temperatures, direct sunlight, or moisture.
  • Regularly check cables and connectors for any signs of wear or damage. Replace damaged components immediately.
  • Store the charger in a cool, dry place when not in use.

9. Troubleshooting

  • Charger not powering on: Ensure the power cable is securely connected and the AC switch is on. Verify the input voltage is within the specified range (DC 7-28V or AC 100-240V).
  • Charging error/abnormal battery reading: Double-check that the correct battery type and cell count are selected. Ensure the balance lead is properly connected for lithium batteries. Inspect the battery and connectors for damage.
  • Overheating: Ensure the cooling fan is not obstructed and the charger is in a well-ventilated area. Check the 'Safe inter Temp.' and 'Safe Exter Temp.' settings in Security Settings.
  • Display issues: If the display is blank or flickering, try restarting the charger. If issues persist, check for firmware updates.
  • Inaccurate voltage readings: Perform a manual voltage calibration as described in section 7.5.

10. Specifications

CategoryParameterValue
InputAC Input100-240V@MAX 100W
DC Input7-35V@MAX20A
Battery TypeLiPo/LiHV/LiFe/Lion/LTO1-6S
NiMh/PBNiMh @1-16S, PB @1-10S
Balance Current800mA @4.2V
Accuracy<0.005V
ChargePower0.1-15A@300W
Current0.1-15A@300W
DischargePower (Rec/Ext Mode)0.1-15A@300W
Power (Internal Mode)0.1-3A@15W
Current0.1-15A
USB A Output5.0V@10W or upgrade
Voltage Range1.0V-5.0V @1-6S
Internal Resistance0.1mΩ-99mΩ @1-6S
Measure SignalPWM880us-2200us@20-400hz
PPM880us-2200us*8 CH@20-50hz
SBUS880us-2200us*16 CH@20-100hz
Output SignalPWM500us-2500us@20-1000hz
PPM880us-2200us*8 CH@50hz
SBUS880us-2200us*16 CH@74hz
Output Power0.5-15A@1-28V Mode: CC+CV
DisplayLCDIPS 2.4 inch 320*240 resolution
AccessorTF CardSupport 128MB-16GB
Product DimensionsSize112mm*73mm*38mm
Weight245g
Individual PackingSize144mm*125mm*43mm
Weight380g

11. Warranty and Support

ToolkitRC products are covered by a manufacturer's warranty against defects in materials and workmanship. For specific warranty terms, support, and service inquiries, please visit the official ToolkitRC website at www.toolkitrc.com or contact their customer service directly.

12. User Tips

  • Verify Settings: Always double-check your battery type, cell count, and current settings before starting any charge or discharge cycle to ensure compatibility and safety.
  • Monitor Progress: Although the M7AC has safety features, it's good practice to monitor the charging/discharging process, especially with new battery types or settings.
  • Keep Firmware Updated: Regularly check the ToolkitRC website for firmware updates to ensure optimal performance and access to new features.

13. Product Video

Watch this video for an unboxing and basic overview of the ToolkitRC M7AC charger:

Unboxing and initial setup of the ToolkitRC M7AC Intelligent Charger.

© 2022 ToolkitRC Technology (Shenzhen) Co., Ltd. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.