ToolkitRC M9

Contents

ToolkitRC M9 Multifunctional Charger User Manual

Model: M9 | Brand: ToolkitRC

Manual Version V1.0 (2021.12)

1. Introduction

Thank you for purchasing the M9 balance charger. Please read this manual carefully before use to ensure proper operation and safety.

Key Points

  • Tips: General advice for optimal use.
  • Important: Critical information to prevent damage or hazards.
  • Information: Additional details and explanations.

Further Information

To ensure you have the best experience with this product, stay up to date with news, information, and firmware updates for your charger. This information can be found at www.toolkitrc.com.

2. Safety Instructions

Always prioritize safety when operating the M9 charger.

  1. The M9 accepts an input voltage of DC 7.0-35.0V. Ensure the charger is connected only to a suitable power source with correct polarity.
  2. Do not use this product in hot, humid, flammable, or explosive environments.
  3. Please do not use this charger without supervision. Never leave charging batteries unattended.
  4. When not using this product, always unplug the input power.
  5. When using the charging function, set a current that matches the battery. Do not set an excessive current to avoid damaging the battery. Always check your battery manufacturer's guidelines for correct charging instructions.

Glossary of Battery Terms

  • LiPo: Lithium polymer battery, nominal voltage 3.70V, fully charged at 4.20V.
  • LiHV: High-voltage lithium battery, nominal voltage 3.85V, fully charged at 4.35V.
  • LiFe: Iron-lithium battery, nominal voltage 3.30V, fully charged at 3.60V.
  • Lion: Lithium-ion battery, nominal voltage 3.60V, fully charged at 4.10V.
  • LTO: Lithium-ion battery, nominal voltage 2.40V, fully charged at 2.70V.
  • NiMh: Nickel-metal hydride battery, nominal voltage 1.20V.
  • PB: Lead-acid battery, nominal voltage 2.00V.

3. M9 Layout

Familiarize yourself with the components and ports of your M9 charger.

ToolkitRC M9 charger in box

ToolkitRC M9 Multifunctional Charger with packaging.

M9 Charger Front Layout Diagram

Front view of the M9 charger with labeled components: Display, Output port, Balance Signal port, USB A+C output, Scroll wheel, Exit button.

M9 Charger Back Layout Diagram

Back view of the M9 charger with labeled components: Speaker, TF Card slot, Input port, Cooling fan.

4. Quick Start Guide

  1. Connect a 7-35V DC power supply to the input port on the back of the M9.
  2. The display will show the boot logo for 2 seconds.
  3. A welcome sound will play (voice pack dependent).
  4. After booting, the screen enters the main interface:
M9 Charger Main Interface Display

Main interface showing input voltage, power, temperature, current, and individual cell voltages.

  1. Press and hold [Exit] to enter the auxiliary function interface.
  2. Scroll the [Scroll Wheel] to switch between pages.
  3. With the charger idle, short press [OK] to set charging parameters. During charging, press [OK] to adjust amperage or stop the process.
  4. With the charger idle, press and hold [OK] to enter the system setting interface.
  5. Short press [Exit] to return to the previous interface.

5. Charge and Discharge Settings

From the main interface, short press [OK] to enter the charging function. If battery selection is enabled in system settings, the battery selection interface will appear.

5.1. Battery Type Setting

Scroll the [Scroll Wheel] to select a preset battery type or create a new one. Up to 32 battery profiles can be stored. Press [Enter] to access specific battery settings.

Battery Selection Menu

Battery selection menu showing LipoAT, LiHv, and New options.

Move the cursor to [Battery Type] and press [OK] to modify the battery type. The charger supports LiPo, LiHV, LiFe, Lion, LTO, NiMh, and PB, plus a smart battery mode.

Battery Type Options Menu

Menu displaying various battery types: Lipo, LiHv, LiFe, Lion, NiMh.

Warning: Ensure the correct battery type is selected before charging. An incorrect choice can damage the battery or cause a fire hazard. Do not charge non-compatible battery chemistries.

5.2. Cell Setting

Move the cursor to [Battery Section] and press [OK] to modify the number of cells.

Cells Selection Menu

Menu for selecting the number of cells (1S to 5S shown).

Rotate the [Scroll wheel] to adjust the value. When set to [Auto], the charger automatically identifies the number of cells using balance port data. Short press [OK] and [Exit] to save.

Tip: If a battery is over-discharged or over-charged, it may cause an incorrect cell count. Adjust manually if needed. Incorrect cell count can lead to overcharging and fire risk. Connecting the balance port improves accuracy.

5.3. Work Mode

Move the cursor to [Mode] and press [OK] to modify the work mode.

Work Mode Selection Menu

Work mode options: Charge, DisCHG (Discharge), StoCHG (Storage Charge).

Lipo, LiHV, LiFe, Lion, LTO batteries can be charged, discharged, and stored. NiMh batteries can be charged, discharged, or cycled. PB batteries can be charged and discharged. Short press [OK] and [Exit] to save.

5.4. Discharge Mode

Under discharge, storage, and cycle modes, the discharge option appears. Move the cursor to [Discharge Mode] and press [OK] to modify.

Discharge Mode Selection Menu

Discharge mode options: Inter (Internal), Recycle, External.

  • Normal mode (Inter): Discharges using internal heat dissipation, max 3.0A@20W.
  • Recycle mode: When a battery is used as input, power is recovered to the input battery, max 20.0A@600W.
  • External mode: When an external discharge load is connected to the input port and the output port to the battery, it can discharge through this function, max 20.0A@600W.

5.5. Input Max Voltage

When Recycle discharge mode is selected, the [Max Input Vol.] option appears. Move the cursor and press [OK] to adjust. If the input voltage reaches this value during discharge, the discharge will stop.

Input Max Voltage Setting Menu

Menu for setting maximum input voltage (e.g., 28.0V).

Tip: Set Max input voltage to the highest protection voltage of your power supply. The charger will stop recycling once this voltage is reached.

5.6. End Voltage Setting (TVC)

Move the cursor to [End Voltage] and press [OK] to modify the end voltage for individual cells. This is the charge cut-off voltage (range: +/- 50mV of full voltage) or discharge cut-off voltage. Scroll the [Scroll wheel] to adjust (0.01V steps).

End Voltage Setting Menu

Menu for setting end voltage (e.g., 4.20V).

Tips:

  • Only LiPo, LiHV, LiFe batteries allow cut-off voltage adjustment.
  • Do not modify cut-off voltage if unfamiliar with battery characteristics.
  • TVC: Terminal Voltage Control.

5.7. Current Setting

Move the cursor to [Charge Current] or [DisCHG Current] and press [OK] to modify. Rotate the [Scroll Wheel] to adjust (0.1A steps). The charger supports up to 10.0A.

Discharge Current Setting Menu

Menu for setting discharge current (e.g., 2.0A).

Tip: Set the charging rate to 1-2C according to battery capacity. For a 2000mAh battery, set charge current to 2.0-4.0A.

5.8. NiMh Setting (PeakV)

When NiMh battery type is selected, the peak voltage value for a fully charged battery can be set (range: 5mV-15mV).

NiMh Peak Voltage Setting Menu

Menu for setting NiMh PeakV (e.g., 7mv).

Tip: This function is only available for NiMh cells. PeakV refers to the maximum voltage drop per cell when the nickel-metal hydride battery is fully charged.

5.9. Cycle Setting

When NiMh battery type is selected and under cycle mode, options for Cycle time and Rest time appear.

NiMh Cycle Setting Menu

NiMh cycle settings including Nixx Peak, Charge/Discharge Current, Cycle times, and Rest time.

Move the cursor to [Cycle times] and press [OK] to set the range (2-12 cycles). The charger will follow a discharge->charge pattern. Move the cursor to [Rest time] and press [OK] to set the rest time (2-10 minutes).

Cycle Times and Rest Time Menus

Menus for setting cycle times (e.g., 4) and rest time (e.g., 4Min).

5.10. External Load Setting

When external discharge is selected, the external load setting appears. Set the wattage according to the external load used.

External Load Setting Menu

Menu for setting external load wattage (e.g., 30W).

5.11. Smart Battery Setting

When UAV battery is selected, only two options are available: Drone model and Max current.

UAV Battery Setting Menu

UAV battery setting menu showing Battery Type, Drone model, and Max Current.

Move the cursor to [Drone model] and press [OK] to select between different drone models.

Drone Model Selection Menu

Drone model options: Mavic2 17.6V, MavicS 13.05V, Phantom 17.4V, Inspire 26.1V.

Move the cursor to [Max Current] and press [OK] to set the charge current (range: 0.5A to 20A).

5.12. Charge and Discharge Work Interface

When charging or discharging begins, the charger enters the following interface:

Charging/Discharging Work Interface

Display during charging/discharging, showing input voltage, accumulated power, temperature, main port voltage/current, working time, charged capacity, and cell voltages.

Rotate the [Scroll Wheel] to toggle between three different displays:

  • P1: Power selection in system settings
  • 24.01V: Input voltage
  • 0.0Wh: Accumulated power consumption
  • 45.0°C: Internal temperature of the charger
  • V: Constant voltage sign
  • C: Constant current sign
  • 24.01V: Main port voltage
  • 2.00A: Main port current
  • 010:00: Working time
  • 338mAh: Charged capacity
  • 1 4.000V: Voltage for the first battery cell
  • T 24.00V: Total voltage measured at balance lead.
  • -.---v: No battery connected

Short press [OK] to dynamically set the charge current or stop charging.

Adjustment Menu for Current and Stop

Adjustment menu to change current or stop the process.

To end the charge/discharge process, short press [OK], move the cursor to [Stop], and short press [OK] again. When charging is complete or an error occurs, a popup will appear with an audible tone.

Scroll [Scroll Wheel] to switch to the second page for internal resistance information.

Internal Resistance Display

Display showing internal resistance for each cell (e.g., 5.2mΩ for cell 1) and total internal resistance (e.g., 32mΩ).

Scroll [Scroll Wheel] to switch to the third page for general information.

Charging Status Display

Charging status display showing current status, end voltage/charge current, and current charging power.

Tips:

  • Never leave cells unattended during charging/discharging.
  • For lithium batteries, balancing occurs only if the balance plug is connected. The charger will automatically balance each cell if detected.
  • Charging will automatically start for the next battery if the initial battery is disconnected after being fully charged. If a set number of cells is used, ensure the subsequent cell count matches the initial battery's cell count. If set to automatic, ensure the cell count matches what is detected.

6. Accessibility Functions

After selecting and long pressing [Exit] in the main interface, you can enter the auxiliary function interface.

Accessibility Menu

Accessibility menu showing options: Measure resistance, Measure signal, Signal output, ESC test, Power.

6.1. Measure Resistance

Short press [OK] to test the internal resistance of the connected battery and return to the main interface display.

6.2. Measure Signal

Move the cursor to [Measure signal], short press [OK] to enter the signal test interface. Scroll [Scroll wheel] to select the signal type (PWM, PPM, SBUS).

Measure Signal PWM Display

Measure signal interface for PWM, showing pulse width (1500us) and frequency (20.0ms/50Hz).

Measure Signal PPM Display

Measure signal interface for PPM, showing values for 8 channels.

For SBUS, scroll [Scroll wheel] to display channels 1-8, channels 9-16, and overall status.

Measure Signal SBUS Channels 1-8 Display

Measure signal interface for SBUS, showing values for channels 1-8.

Measure Signal SBUS Channels 9-16 Display

Measure signal interface for SBUS, showing values for channels 9-16.

Measure Signal SBUS Status Display

Measure signal interface for SBUS, showing Channel DG1/DG2, Frame lost, Failsafe, and Endbyte status.

6.3. Signal Output

Move the cursor to [Signal Output], short press [OK] to enter. Scroll [Scroll wheel] to select the signal type (PWM, PPM, SBUS).

For PWM, scroll the [Scroll Wheel] to [Manual], press [OK] to set the output mode (manual, auto 1, auto 2, auto 3). In manual mode, adjust pulse width (800-2200us) and cycle (2.5ms/400Hz to 50.0ms/20Hz).

Signal Output PWM Menu

Signal output menu for PWM, showing mode (Manual), width (1500us), and cycle (20.0ms/50Hz).

For PPM, scroll [Scroll wheel] to move the cursor to the channel value to be modified. Press [OK] to modify the output pulse width.

Signal Output PPM Menu

Signal output menu for PPM, showing values for 8 channels.

For SBUS, scroll [Scroll wheel] to move the cursor to the channel value to be modified. Press [OK] to modify the output pulse width.

Signal Output SBUS Channels 1-8 Menu

Signal output menu for SBUS, showing values for channels 1-8.

Signal Output SBUS Channels 9-16 Menu

Signal output menu for SBUS, showing values for channels 9-16.

Signal Output SBUS Status Menu

Signal output menu for SBUS, showing Channel DG1/DG2, Frame lost, Failsafe, and Endbyte status.

6.4. ESC Test

Select [ESC test] with the cursor, short press [OK] to enter. Scroll [Scroll wheel] to pulse width/cycle, press [OK] to change the value.

ESC Test Display

ESC test display showing pulse width (1000us), frequency (20.0ms/50Hz), voltage (19.80V), and current (0.03A).

6.5. Power (Adjustable Power Supply)

Select the adjustable power supply with the cursor, and short press [OK] to enter. Set voltage and current. Move the cursor to [Start], short press [OK] to start power output and return to the main interface.

Power Output Settings Menu

Power output settings menu showing Output Voltage (20.1V) and Max Current (2.0A).

6.6. USB Information

Select [USB information] with the cursor, and short press [Enter] to view USB information.

USB Information Display

USB information display showing Voltage (20.00V), Current (3.25A), Time (01:59:33), Capacity (82.26Wh), and Protocol (PD FIX).

7. System Settings

After long pressing [OK] in the main interface, you can enter the system setting interface.

System Settings Menu

System settings menu showing Input settings, Security settings, Personalization, Battery selection, Continuous, Work completed.

Short press to expand the settings.

7.1. Input Settings

Expanded Input Settings Menu

Expanded input settings: Power select (Auto P1), Power type (Adapter), Max power (90W), Max current (12.0A), Voltage range (7.0 - 24.0V).

  • Power selection: Preset power 1, power 2, power 3.
  • Power type: Choose between battery pack and adapter. Recycle mode is enabled for battery packs, disabled for adapters.
  • Max power: Maximum wattage allowed via the input port during charging.
  • Max current: Maximum current allowed via the input port during charging.
  • Voltage range: Input voltage range.

7.2. Security Settings

Short press to expand settings.

Expanded Security Settings Menu

Expanded security settings: Safe inter Temp (70°C), Safe Exter Temp (50°C), Safe time (200Min), Safe capacity (20Ah).

  • Safe Inter. Temp.: Charging stops if device internal temperature exceeds this value.
  • Safe Exter. Temp.: Charging stops if environment temperature exceeds this value.
  • Safe time: Maximum time limit for continuous charging/discharging.
  • Safe capacity: Maximum accumulated capacity for a charging/discharging session.

7.3. Personalization

Short press to expand settings.

Expanded Personalization Settings Menu

Expanded personalization settings: Backlight (10), Operation volume (Low), Announce volume (Medium), Warning volume (High), Language (English), Theme style (Light).

  • Backlight: Brightness level (1-10).
  • Operation volume: Scroll wheel volume (off, low, medium, high).
  • Announce volume: Menu readout volume (off, low, medium, high).
  • Warning volume: Warning tone volume (off, low, medium, high).
  • Language: System display language (English, Chinese, etc.).
  • Theme style: Light and dark themes.

7.4. Other System Settings

Other System Settings Menu

Other system settings: Battery selection (OFF), Work completed (Trickle), Balance start Vol. (Always), Continuous work (OFF), Default, ID (FF3005D3 - V1.00).

  • Battery selection: Option to show/hide frequently used parameters.
  • Work completed: Whether to stop or trickle charge after charge completion.
  • Balance start Vol: Balance cells prior to full current charge.
  • Continuous work: Enables/disables continuous charging/discharging after battery replacement.
  • Default: Restore factory settings.
  • ID: Independent ID for each device.

8. Customize Functions

The M9 supports customizable boot images and voice packs. Connect the USB-A cable (included) to your computer. Two USB drives will appear: one for firmware upgrades (Toolkit USB drive) and one for custom files. The root directory contains two folders: LOGO (for boot images) and SOUNDS (for voice files).

8.1. Boot Image

When the M9 is turned on, it automatically reads the file named logo.bmp in the LOGO folder. If read successfully, this image will be displayed as the startup page.

ToolkitRC M9 Boot Image Example

Example of a custom boot image for the ToolkitRC M9.

Tips:

  • Only supports BMP file format with a resolution of 240*320 pixels.
  • If the file cannot be read, the default startup page will be displayed.

8.2. Broadcast Voice

The M9 reads voice files from the SOUNDS folder. Voice files for each language are classified into separate folders. The description of folders and files is as follows:

Name Description Name Description
CHIChineseDEUGerman
ENGEnglishESPSpanish
FRAFrenchITAItalian
JAPJapaneseKORKorean
PORPortugueseTRATraditional

Voice file descriptions:

File name File description
0000.wav-0090.wavNumber 0-90 voice
0100-0109.wavNumber 100-1000 voice
0167-0176.wavNumbers .1-.9 Voice
Bootup.wavBootup sound
Warning.wavWarning sound
OtherMenu broadcast Voice

Tip: Only supports Wav file format, Mono file.

9. Other Functions

9.1. Firmware Upgrade

Connect the M9 to your computer using the USB cable. Your computer will recognize a USB drive named 'Toolkit'. Download the upgrade file (app.upg) from the official ToolkitRC website and overwrite the files in the drive to upgrade the firmware.

9.2. USB Fast Charge Output

The M9 features TYPE-C + TYPE-A dual fast charge output, with a maximum output of 65W. It supports various fast charge protocols including PD 3.0/PD2.0/PPS/QC4/QC3.0/QC2.0/AFC/FCP/SCP/PE2.0/PE1.1/SFCP/VOOC.

9.3. Automatically Continue Charging/Discharging

When a battery is fully charged, you can connect the next battery, and the device will automatically continue to charge and discharge. This function can be enabled or disabled in the settings menu.

9.4. Fan Level

  • If the internal temperature exceeds 45°C, the fan operates at half speed to reduce noise.
  • If the internal temperature exceeds 53°C, the fan operates at full speed to enhance heat dissipation.

9.5. Manual Voltage Calibration

With the M9 powered off, press and hold the [roller]. While holding, connect the power supply. The system will enter manual voltage calibration mode. Use an external voltmeter to measure the actual voltage of each battery. Move the cursor to the corresponding voltage value and modify it to match the voltmeter reading. After calibration, move the cursor to 'save', short press once (the buzzer will beep), and the save is successful. Exit or shut down after calibration.

9.6. Full Charge Mode

When a lithium battery is fully charged, the device will prompt "Fast charge complete". If the battery is not removed, the charger will trickle charge until the battery is disconnected.

10. User Tips

  • Voltage Calibration: The M9's voltage measurement can be calibrated for accuracy. This can be done via the device menu to match external meters, as confirmed by users.
  • Firmware Updates: Regularly check the ToolkitRC website for firmware updates to ensure optimal performance and access new features.
  • Screen Angle: The adjustable screen angle is a convenient feature for comfortable viewing during operation.
  • Voice Packs: Explore customizable welcome screens and voice packs to personalize your charger experience.

11. Troubleshooting

  • Incorrect Cell Count: If the charger displays an incorrect cell count, especially after a battery has been over-discharged or over-charged, manually adjust the cell count in the settings. Always connect the balance port for more accurate detection.
  • Charging Not Starting/Stopping Unexpectedly: Check the selected battery type, charge current, and end voltage settings. Ensure the input power supply is within the specified voltage range (7.0-35.0V). Review security settings like 'Safe Inter Temp', 'Safe Exter Temp', 'Safe time', and 'Safe capacity' which can halt operations.
  • Charger Not Responding: Ensure the input power is connected correctly. If the device is unresponsive, try disconnecting and reconnecting the power.
  • Display Issues: If the boot image is not displaying correctly, verify that the logo.bmp file in the LOGO folder is 240x320 pixels and in BMP format.
  • Voice Issues: If voice prompts are incorrect or missing, check the SOUNDS folder for correct language subfolders and WAV file formats (mono).
  • Inaccurate Voltage Readings: Perform a manual voltage calibration as described in section 9.5 using a reliable external voltmeter.

12. Specifications

Category Parameter Value
InputInput Voltage7-35V@MAX25A
Battery TypeLiPo, LiHV, LiFe, Lion, LTO@1-8S; NiMh@1-20S; Pb@1-10S
ChargeBalance Current1000mA @4.2V
Accuracy<0.005V
Power0.1-20A@600W
Discharge Power0.1-20A@600W (Rec/Ext Mode); 0.1-3A@20W (Internal Mode)
USB A+COutput5-20V@65W PD QC PPS AFC SCP
Voltage1.0V-5.0V @1-6S
Internal ResistanceMeasurement Range0.1mΩ-99Ω @1-8S
MeasurePWM880us-2200us@20-400Hz
PPM880us-2200us*8 CH@20-50Hz
SBUS880us-2200us*16 CH@20-100Hz
OutputPWM500us-2500us@20-1000Hz
PPM880us-2200us*8 CH@50Hz
SBUS880us-2200us*16 CH@74Hz
Power1-20A@1-35V Mode: CC+CV
DisplayLCDIPS 2.4 inch 320*240 resolution
Size108mm*71mm*36mm
ProductWeight235g
Individual Packing Size135mm*81mm*44mm
Individual Packing Weight330g

13. Warranty and Support

ToolkitRC products are manufactured to high quality standards. For warranty claims, technical support, or service inquiries, please visit the official ToolkitRC website at www.toolkitrc.com or contact your authorized dealer. Please retain your proof of purchase for any warranty claims.

For the latest user manual (PDF) and other item guides, please refer to the official product page or the manufacturer's website.

Official product video demonstrating key features of the ToolkitRC M9 charger, including its ergonomic display, customizable voice packs, multi-signal output, and dual USB fast charging capabilities.

© ToolkitRC 2021. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.