1. Product Information
This manual provides detailed instructions for the installation, operation, and maintenance of the JAGNES Windshield Washer Nozzles.
- Product Name: Washer Nozzle
- Model: GY1ZTA01-JAGNES-PSZ (OE# 98630-2L100)
- Brand: JAGNES
- Placement: FRONT
- Material: Plastic
- External Testing Certification: ISO9000
- Origin: Mainland China
- Compatibility: For Hyundai i30 MK1, Elantra Touring MK1, Kia Cadenza / K7 MK1 (Years: 2007-2016)
For additional information, you can refer to the official user manual PDF: User manual (PDF)
2. Safety & Warnings
Important Safety Information
- Read all instructions before use.
- Inspect the product before each use; do not use if damaged.
- Avoid touching the nozzle tip with bare hands (oils can clog the spray hole).
- Do not install nozzles while the engine is running or the wipers are moving.
- If unsure about compatibility, consult your vehicle's manual or a professional mechanic.
3. Installation Guide
3.1. Pre-Installation Preparation
- Turn off the vehicle: Ensure the engine is off and the ignition is in the "off" position.
- Lift the wiper arm: Gently pull the wiper arm away from the windshield until it stays in the upright position (use a soft cloth to protect the windshield if needed).
- Locate the old nozzle: Find the existing nozzle on the top of the wiper arm (usually a small plastic or metal component with a tiny hole for water flow).
- Clean the area: Wipe the wiper arm and surrounding area with a clean cloth to remove dirt, dust, or debris.
3.2. Tools & Materials Needed
- New wiper nozzles (included in the kit)
- Small flathead screwdriver, pick tool, or needle-nose pliers (to remove old nozzles)
- Cleaning brush (included, for old nozzles)
- Clean cloth (to wipe the windshield and wiper arm area)
- Isopropyl alcohol (optional, to clean residue)
3.3. Step-by-Step Installation
Step 1: Remove the Old Nozzle
- If the old nozzle is clamped on: Use a small flathead screwdriver to gently pry the clip/retainer (a small plastic tab) away from the wiper arm. Once loose, slide the old nozzle off.
- If the old nozzle is screwed on: Use a small screwdriver to turn the nozzle counterclockwise (left) until it detaches from the wiper arm.
- Note: If the old nozzle is stuck, use a pick tool to carefully lift the edge – avoid applying excessive force to prevent damage.
Step 2: Clean the Mounting Hole
- Use a cleaning brush (included) or a cotton swab to clear any debris, old sealant, or mineral deposits from the mounting hole on the wiper arm.
- Wipe the area with a cloth dampened with isopropyl alcohol to ensure a clean surface (this helps the new nozzle adhere better).
Step 3: Install the New Nozzle
- Clamp-on nozzles: Slide the new nozzle into the mounting hole. Align the clip/retainer with the groove on the wiper arm, then press firmly until it clicks into place.
- Screw-on nozzles: Insert the nozzle into the mounting hole, then turn clockwise (right) by hand until snug. Do not overtighten (it may crack the plastic).
- Tip: For adjustable nozzles, align the spray direction with the windshield (aim slightly toward the center) before securing.
4. Operation
4.1. Test the Water Flow
- Reconnect the wiper arm to its base (if lifted) and lower it onto the windshield.
- Turn on the vehicle's ignition (do not start the engine) and activate the windshield washer system.
- Check that water sprays evenly across the windshield. If the spray is too wide/narrow, adjust the nozzle:
- Gently bend the nozzle tip (for plastic nozzles) or rotate the adjustment ring (if included) to direct the spray.
5. Maintenance
5.1. Post-Installation Checks
- Leak test: After testing, inspect the nozzle and wiper arm for leaks. Tighten slightly if needed (but avoid over-tightening).
- Alignment check: Ensure the nozzle does not interfere with the wiper blade movement. Adjust position if necessary.
5.2. Cleaning
Regularly check the nozzle tips for clogs. If clogged, use a thin pin or the included cleaning brush to gently clear the spray hole. Ensure the washer fluid reservoir is adequately filled with appropriate fluid.
6. Troubleshooting Tips
| Issue | Solution |
|---|---|
| No water spray | Check washer fluid level; ensure lines are not clogged (flush with water if needed). |
| Uneven spray | Adjust nozzle angle or clean the nozzle tip with a pin. |
| Nozzle falls off | Ensure it is fully seated in the mounting hole; replace if damaged. |
| Holes at outlet not large enough (reduced spray) | Verify compatibility with your vehicle's system. If the spray is insufficient, consider checking for obstructions or consulting a professional. |
7. Specifications
| Attribute | Value |
|---|---|
| Brand Name | JAGNES |
| Model Name | For Hyundai i30 MK1 Elantra Touring MK1 Kia Cadenza / K7 MK1 |
| OEM NO. | 98630-2L100 |
| Placement | FRONT |
| Year Compatibility | 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016 |
| Special Features | Windscreen Wiper Spray Jet Nozzle |
| Material | Plastic Washer Nozzle |
| External Testing Certification | ISO9000 |
| Origin | Mainland China |
| Package Contents | 2 Pieces (per lot) |
| Package Weight | 0.02 kg |
| Package Dimensions | 17cm x 17cm x 2cm |
8. User Tips
- The material quality is reported to be very similar to original parts, ensuring a good fit and appearance.
- Ensure the nozzle is fully compatible with your specific vehicle model and year to avoid issues with spray pattern or fitment. Some users reported issues with specific Kia models.
- If the spray is not optimal, check for clogs and adjust the nozzle angle as described in the troubleshooting section.
9. Warranty and Support
This product is manufactured to high-quality standards. For any issues or support, please contact the manufacturer directly via the email provided in the product information section.
Manufacturer Email: benjaminwz5jan@outlook.com
EU Authorized Representative Email: successservice2@hotmail.com