SHIMANO ULTEGRA R8110

Contents

Shimano ULTEGRA R8110 Brake Calipers User Manual

Model: ULTEGRA R8110 | Brand: SHIMANO

Introduction

This manual provides essential information for the safe and proper installation, operation, and maintenance of your Shimano ULTEGRA R8110 series brake calipers. Please read this manual thoroughly before using the product and keep it for future reference.

The Shimano ULTEGRA R8110 series includes direct mount front brake calipers (BR-R8110F) and rear seat stay mount rear brake calipers (BR-R8110RS), designed for road bicycles.

Shimano ULTEGRA BR-R8110F/RS Brake Calipers
Figure 1: Shimano ULTEGRA BR-R8110F/RS Brake Calipers (Front and Rear)

Safety Information

⚠ Warning & Notice

  • This product is not a toy and is not suitable for children under 16 years old without adult supervision.
  • Keep all small parts (e.g., screws, pulleys) away from infants and toddlers to avoid choking hazards.
  • Always wear appropriate protective gear (helmet, gloves, knee pads) when operating the bicycle.
  • Do not use the product in traffic without proper training.
  • Ensure the brake calipers are correctly installed and adjusted before use. Improper installation may cause braking failure, leading to falls or serious injury.
  • Do not modify the brake caliper's structure or components. Unauthorized modifications void compliance and safety guarantees.
  • This product is not intended for use with children's bicycles (refer to EN 14765 for children-specific requirements).
  • Keep the brake calipers away from corrosive substances (acids, solvents) and extreme temperatures to prevent mechanical failure.

Additional Safety Notes

  • Regularly inspect the brake calipers for wear, damage, or loose connections.
  • Replace worn parts immediately using genuine Shimano accessories.

Usage Restrictions

Not Suitable For:

  • Children under 16 years old (without adult supervision).
  • Bicycles with wheel sizes below 26" or above 29".
  • Electric bicycles with motor power exceeding 250W.
  • Off-road use in extreme conditions (e.g., rock climbing, steep descents >30°).

Environmental Restrictions: Do not use in saltwater environments (e.g., coastal areas) without proper corrosion protection.

Installation and Setup

Proper installation is crucial for the safe and effective operation of your brake calipers. If you are unsure about any step, consult a professional bicycle mechanic.

Tools Required:

  • Hex wrenches (appropriate sizes for mounting bolts)
  • Cable cutters
  • Brake cable and housing
  • Torque wrench (recommended for precise tightening)

Installation Steps:

  1. Mounting the Caliper: Attach the brake caliper to the designated direct mount points on your bicycle frame (front fork for BR-R8110F, seat stay for BR-R8110RS). Ensure the caliper is oriented correctly.
  2. Securing Bolts: Tighten the mounting bolts to the manufacturer's specified torque. Over-tightening can damage components, while under-tightening can lead to brake failure.
  3. Installing Brake Pads: Ensure brake pads are correctly installed and aligned with the rim braking surface. The pads should contact the rim squarely and not rub on the tire or fork/frame.
  4. Routing Brake Cable: Route the brake cable through the housing and attach it to the caliper. Ensure smooth cable movement without kinks or excessive friction.
  5. Adjusting Cable Tension: Adjust the cable tension so that the brake levers have the appropriate amount of free play and the pads engage the rim firmly when the lever is squeezed.
  6. Centering Caliper: Center the brake caliper so that both pads are an equal distance from the rim. Use the centering adjustment screw if available, or loosen the mounting bolts slightly, center the caliper, and re-tighten.
  7. Final Check: Before riding, test the brakes thoroughly at a slow speed. Ensure both front and rear brakes engage smoothly and effectively. Check for any rubbing or unusual noises.
Shimano ULTEGRA BR-R8110F Front Brake Caliper
Figure 2: Shimano ULTEGRA BR-R8110F Front Brake Caliper
Shimano ULTEGRA BR-R8110RS Rear Seat Stay Mount Brake Caliper
Figure 3: Shimano ULTEGRA BR-R8110RS Rear Seat Stay Mount Brake Caliper

Operation

The Shimano ULTEGRA R8110 brake calipers provide reliable stopping power for road cycling. To operate the brakes:

  1. Grip the brake levers firmly with your hands.
  2. Squeeze the levers towards the handlebars to engage the brakes. The right lever typically controls the rear brake, and the left lever controls the front brake (this may vary by region).
  3. Apply progressive pressure to the levers for controlled deceleration. Avoid sudden, hard braking, especially with the front brake, as this can cause loss of control.
  4. Modulate braking force by varying the pressure on the levers.

Familiarize yourself with the feel and response of your brakes in a safe, open area before riding in traffic or at high speeds.

Maintenance

Regular maintenance ensures optimal performance and longevity of your brake calipers.

Maintenance Interval:

  • Inspect and lubricate the brake calipers every 500km or every 3 months, whichever comes first.

Maintenance Checklist:

  • Brake Pads: Check brake pads for wear. Replace them if the wear indicator is no longer visible or if they are worn down to the minimum thickness. Ensure pads are clean and free of debris.
  • Brake Cables: Inspect brake cables and housing for fraying, corrosion, or damage. Replace if necessary. Lubricate cables for smooth operation.
  • Caliper Body: Clean the caliper body regularly to remove dirt and grime. Check for any cracks or damage to the caliper arms or pivots.
  • Mounting Bolts: Verify that all mounting bolts are securely tightened to the correct torque specifications.
  • Springs and Pivots: Ensure the return springs are functioning correctly and the caliper pivots move freely. Apply a small amount of appropriate lubricant to pivot points if needed.

Troubleshooting

Problem Possible Cause Solution
Weak braking power Worn brake pads, loose cable, contaminated rim/pads Replace pads, adjust cable tension, clean rim/pads
Brakes rub on rim Caliper not centered, bent rim, sticky pivots Center caliper, true wheel, lubricate pivots
Squealing noise during braking Contaminated pads/rim, misaligned pads, loose components Clean pads/rim, adjust pad angle, check bolt tightness
Brake lever feels spongy Stretched cable, worn housing, poor cable routing Replace cable/housing, re-route cable for smoother path

Specifications

Feature Detail
Brand Name SHIMANO
Model Number R8110
Use Road Bicycles
Braking System V Brake (Friction Wheel Brake)
Components Caliper Brake
Material Light Alloy
Origin Japan
High-concerned chemical None
Shimano ULTEGRA BR-R8110F brake caliper on a scale showing 183.8g
Figure 4: Approximate weight of a single BR-R8110F caliper (183.8g)

User Tips

  • Always verify the authenticity of your Shimano components. Genuine parts ensure optimal performance and safety.
  • When purchasing, confirm whether you are buying a single caliper (front or rear) or a complete set (front and rear) to ensure you receive the correct components for your needs.
  • Regularly check for loose connections and wear, as noted in the maintenance section, to keep your brakes performing excellently.

Frequently Asked Questions (FAQ)

Q: Is this product original Shimano?
A: Based on user feedback, the product is generally considered original. Always purchase from reputable sellers to ensure authenticity.
Q: Does this include a front and rear brake set, or just one caliper?
A: The product may be sold as individual front (BR-R8110F) or rear (BR-R8110RS) calipers, or as a set. Please check the specific product option you select to confirm what is included in your purchase.

Manufacturer Information and Support

Manufacturer:

Name: Shimano Inc.
Address: 3-1-1 Sakai-cho, Sakai-ku, Osaka, Japan
Contact: support@shimano.com

EU Responsible Person (Authorized Representative):

Name: MJCM SARL
Country: France
Address: 78 avenue des Champs Elysees, Bureau 326, 75008 Paris, France
Phone: +33-752907452
Email: mjcm190928@gmail.com

Compliance:

This product complies with the following EU regulations and standards:

  • General Product Safety Directive (GPSD): 2001/95/EC
  • Mechanical Directive (MD): 2006/42/EC
  • Harmonized Standards: EN ISO 4210-2:2015 (Bicycle safety requirements for city, trekking, mountain bikes), EN 14781:2015 (Racing bicycle specific safety standards)
  • REACH Regulation (EC) No 1907/2006 (Restriction of hazardous substances)

A complete copy of the Declaration of Conformity (DoC) is available upon request from the EU Responsible Person.

For further detailed instructions, you may refer to the official user manual PDF: Shimano ULTEGRA R8110 User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.