Introduction
The RETEKESS TD157 is a wireless guest paging system designed to streamline customer flow and improve service efficiency in various establishments such as restaurants, cafes, food trucks, hotels, and churches. This system includes a main transmitter unit and multiple coaster pagers, providing reliable communication over a significant distance.
This manual provides detailed instructions for the proper setup, operation, and maintenance of your TD157 paging system to ensure optimal performance and longevity.
Product Components
The RETEKESS TD157 system typically includes the following components:
- 1 x Transmitter Unit: The main calling unit with a keypad and charging slots.
- 16 x Coaster Pagers: Rechargeable pagers for guests.
- 1 x Power Adapter: For the transmitter unit.
Specifications
| Feature | Transmitter | Receiver (Pager) |
|---|---|---|
| Dimension | 238 x 151 x 30mm | 106 x 51 x 11mm |
| Material | ABS | ABS |
| Transmit Power | 240mW | N/A |
| Frequency | 433MHz | 433MHz |
| Power Supply | DC12V/1A | 3.7V/150mAh (LI-Polymer) |
| Launch Distance (Open Area) | >800M | N/A |
| Receiving Sensitivity | N/A | -114dB |
| Standby Time | N/A | ~20 Hours |
| Support Receiver Quantity | 998 (16/SET) | N/A |
| IP Grade | IP32 | IP32 |
| Battery Included | No | Yes |
| Certification | CE, FCC, RoHS | |
Setup Instructions
-
Initial Charging: Place all coaster pagers into the charging slots of the transmitter unit. Ensure they are properly seated. Allow them to charge for at least 20 minutes before initial operation.
The transmitter unit must be powered on for the pagers to automatically turn on when placed in the charging slots.
-
Power On: Connect the power adapter to the transmitter unit and a suitable power outlet. The system will automatically power on.
-
Power Off: To power off all pagers, place them in the main unit's charging slots. On the transmitter keypad, input "99/999" and then press the [Call] button.
-
Entering Setup Mode: Press and hold the [Call] button and the [Clear] button simultaneously until the transmitter screen displays "F1". This indicates entry into the mode selection interface. Use the keypad (1-4) to select the desired setting mode and press [Call]. After making changes, press [Clear] to exit setup mode and return to the standby screen.
- "1": F1 Host ID number setting
- "2": F2 Extension ID number setting
- "3": F3 Buzzer switch setting
- "4": F4 Prompt duration setting
-
Setting Host ID (F1): In setup mode, the screen will flash the current host ID. Enter a new ID (001-999) using the keypad and press [Call] to save. Note: Do not modify the host base number unless necessary, as all pagers will need to be reset. Do not set the base number to "000".
-
Setting Extension ID (F2):
- First, remove all pagers from the base.
- Enter setup mode (F2). The default screen will flash "01".
- Insert the pager to be set into a charging slot. The function light on the pager will flash.
- Within 3 seconds, input the new ID number (1-998) using the keypad and press [Call] to save. The pager will prompt with a flash to confirm successful setting.
- Remove the pager and repeat for the next pager.
- After all pagers are set, press [Clear] to exit.
Important: Do not set "99/999" as an extension number, as this is the shutdown command. To modify an existing pager's ID, simply overwrite the old number with the new one.
-
Setting Beep Switch (F3): In setup mode, the screen flashes "01". Input "0" for off or "1" for on using the keypad, then press [Call] to save.
-
Setting Prompt Duration (F4): In setup mode, the screen flashes "01". Input the desired duration (1-99 seconds) using the keypad, then press [Call] to save.
Operation
Once the system is set up, operating it is straightforward:
-
Give Pager to Guest: When a guest places an order, give them a charged pager.
-
Call Guest: When the order is ready, input the guest's pager number on the transmitter keypad and press the [Call] button.
-
Pager Notification: The guest's pager will activate according to the set prompt mode (flash, beep, or both) and duration, indicating their order is ready.
The system offers two prompt modes: Flash + Beep, and Flash only. Prompt time is adjustable from 1 to 99 seconds. -
Return Pager: The guest returns the pager to the staff, who then place it back into a charging slot on the transmitter base.
This video demonstrates the RETEKESS TD157 paging system in use, highlighting its features such as long transmission distance, customizable logo options, two prompt modes, and support for a large number of pagers.
Maintenance
-
Cleaning: The transmitter features a responsive touch keyboard that is easy to clean. Minor spills of oil or water will not affect normal use. For general cleaning, wipe the units with a soft, damp cloth. Avoid abrasive cleaners or solvents.
The touch keyboard is designed to be responsive and easy to clean, resisting minor spills without affecting functionality. -
Battery Care: Ensure pagers are regularly charged. The built-in 3.7V 300mAh rechargeable battery provides approximately 20 hours of standby time when fully charged.
-
Storage: When not in use for extended periods, store the system in a cool, dry place. Ensure pagers are partially charged before storage to maintain battery health.
Troubleshooting
-
Pagers not responding:
- Ensure pagers are fully charged.
- Verify the pager ID is correctly programmed and matches the number being called on the transmitter.
- Check if the pager is within the effective working distance of the transmitter. Walls and other obstructions can reduce range.
- Confirm the transmitter is powered on and functioning correctly.
-
Short working distance:
- Ensure the transmitter's antenna is properly attached and oriented.
- Minimize obstructions between the transmitter and pagers.
- Environmental factors can affect signal range.
-
Pagers stop working after a short time:
- This could indicate a battery issue. Ensure pagers are charging correctly and holding a charge. If issues persist, contact support.
-
Incorrect plug type received:
- Always verify the plug type (e.g., EU, US, UK) required for your region before purchasing. If an incorrect plug was received, contact the seller for assistance.
User Tips
- Customizable Logo: The pagers can be customized with your restaurant or business logo. Contact the seller for details on this service.
- Expandability: The TD157 system supports up to 998 pagers. If you need more pagers than initially purchased, additional pagers can be acquired and programmed to your existing system.
- Prompt Modes: Take advantage of the two prompt modes (Flash + Beep, or Flash only) and adjustable prompt duration (1-99 seconds) to suit your environment and customer preferences.
- Plug Type: Always confirm the correct plug type (e.g., EU, US, UK) for your region when ordering to ensure compatibility.
RF Energy Exposure and Product Safety Guide
ATTENTION! Before using this radio, read this guide which contains important operating instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulations.
This radio uses electromagnetic energy in the radio frequency (RF) spectrum. All Retekess radios are designed, manufactured, and tested to ensure they meet government-established RF exposure levels. Follow the operating instructions to control your RF energy exposure.
Avoid Choking Hazard
The product contains small parts. Keep out of reach of children under 3 years to prevent choking hazards.
Protect Your Hearing
- Use the lowest volume necessary for your task.
- Turn up the volume only if you are in noisy surroundings.
- Turn down the volume before adding a headset or earpiece.
- Limit the amount of time you use headsets or earpieces at high volume.
- When using the radio without a headset or earpiece, do not place the radio's speaker directly against your ear.
- Excessive sound pressure from earphones and headphones can cause hearing loss.
Avoid Burns
- Do not use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with the skin when the radio is in use, a minor burn can result.
- When the conductive material such as jewelry, keys or chains touch exposed terminals of the batteries, it may complete an electrical circuit (short circuit the battery) and become hot to cause bodily injury such as burns. Exercise care in handling any battery.
- When the transceiver is used for long transmissions, the radiator and chassis will become hot.
Safety Operation
- Do not use charger outdoors or in moist environments; use only in dry locations/conditions.
- Do not disassemble the charger, as this may result in risk of electrical shock or fire.
- Do not operate the charger if it has been broken or damaged in any way.
- Do not place a portable radio in the area over an airbag or in the airbag deployment area. The radio may be propelled with great force and cause serious injury to occupants of the vehicle when the airbag inflates.
- Pull by the plug rather than the cord when disconnecting the charger.
- Unplug the charger from the AC outlet before attempting any maintenance or cleaning.
- The adapter shall be installed near the equipment and shall be easily accessible.
- Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
- The operating temperature of the EUT can't exceed the specified range.
Regulatory Compliance
FCC Requirements
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna; Increase the separation between the equipment and receiver; Connect the equipment into an outlet on a circuit different from that to which the receiver is connected; Consult the dealer or an experienced radio/TV technician for help.
CE Requirements
Henan Eshow Electronic Commerce Co., Ltd declares that the radio equipment type is in compliance with the essential requirements and other relevant provisions of RED Directive 2014/53/EU and the ROHS Directive 2011/65/EU and the WEEE Directive 2012/19/EU. The full text of the EU declaration of conformity is available at www.retekess.com.
Disposal
The crossed-out wheeled-bin symbol on your product, literature, or packaging reminds you that in the European Union, all electrical and electronic products, batteries, and accumulators (rechargeable batteries) must be taken to designated collection locations at the end of their working life. Do not dispose of these products as unsorted municipal waste. Dispose of them according to the laws in your area.
IC Requirements (Licence-exempt radio apparatus)
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
RF Exposure Information
- DO NOT operate the radio without a proper antenna attached, as this may damage the radio and may also cause you to exceed RF exposure limits.
- DO NOT transmit for more than 50% of total radio use time, as more than 50% of the time can cause RF exposure compliance requirements to be exceeded.
- During transmissions, your radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so.
- The device complies with RF specifications when the device used at 5mm from your body. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components.
Warranty and Support
For technical support, repairs, or warranty inquiries, please contact the manufacturer or your point of purchase. Ensure you have your product model (TD157) and purchase details available.
For a list of Retekess-approved accessories for your radio model, visit the official website: www.Retekess.com.
A detailed user manual in PDF format is available for download: View User Manual (PDF).