ToolkitRC M7

Contents

ToolkitRC M7 Multi-Charger User Manual

Model: M7 | Version 1.0

ToolkitRC M7 Multi-Charger front view with screen displaying charging information

ToolkitRC M7 Multi-Charger: A compact and versatile charging solution.

1. Introduction

Thank you for purchasing the ToolkitRC M7 multi-functional charger. This manual provides detailed instructions for safe and efficient operation of your device. Please read it carefully before use.

1.1 Product Overview

The M7 is a versatile tool that integrates a balanced charger and discharger, an electric display, a signal measuring device, and a signal source. It is designed for various battery types and offers multiple functions for RC enthusiasts.

1.2 Key Features

  • Battery Compatibility: Supports LiPo, LiHV, LiFe, Lion (1-6S), NiMh (1-16S), PB (1-10S) batteries.
  • Charging/Discharging: Max 10A charge current (200W), Max 10A discharge current (200W recycle mode).
  • Battery Management: Measures voltage, internal resistance, and provides balance management.
  • Signal Functions: Measures PWM/PPM/SBUS signals (1µs accuracy) and outputs standard PWM/PPM/SBUS signals.
  • Power Supply: Constant current and constant voltage source (1-28V, 1-10A customizable).
  • USB Output: 2.1A@5.0V for mobile device charging.
  • Multi-language System: Firmware upgradable.

2. Safety Information

Please read and understand all safety warnings before operating the M7 charger to prevent injury or damage to the device and batteries.

  1. Input Voltage: The M7 accepts an input voltage of 7-28V. Ensure your power supply voltage is consistent and always verify positive and negative polarity before connecting.
  2. Environment: Do not use this product in environments with excessive heat, humidity, or near flammable and explosive gases.
  3. Supervision: Always operate this product under supervision to prevent accidents.
  4. Power Disconnection: Unplug the input power when the product is not in use.
  5. Charging Current: When using the charging function, set a current that matches your battery's specifications. Setting an excessive current can damage the battery.
  6. Battery Type: Choosing the wrong battery type for charging can damage the battery, the charger, and cause burns. Always select the correct battery type carefully.
  7. Unmarked Batteries: Do not charge batteries that are not clearly marked with their type.

3. M7 Layout and Components

Familiarize yourself with the various ports and controls of your M7 charger.

3.1 Front View

ToolkitRC M7 Layout Diagram showing display, scroll wheel, exit button, output port, and balance port

Diagram: Front view of the M7 charger with key components labeled.

  • Display: 2.0-inch IPS LCD screen for information and settings.
  • Scroll Wheel: Turn left/right to navigate menus, press to confirm (OK).
  • Exit Button: Returns to the previous menu or exits a function.
  • Output Port: Main battery connection (e.g., XT60).
  • Balance Port: For 2-6S battery balancing.

3.2 Rear View

ToolkitRC M7 Charger Rear View showing input port, signal port, cooling fan, and USB output/upgrade port

Image: Rear view of the M7 charger, highlighting the cooling fan and various ports.

  • Input Port: Power input for the charger (7-28V).
  • Signal Port: For signal measurement and output.
  • Cooling Fan: Activates automatically to dissipate heat.
  • USB Output & Upgrade Port: For 5V/2.1A output and firmware updates.

4. Setup and Quick Start

4.1 What's in the Box

ToolkitRC M7 Charger in its retail box with a USB cable and user manual

Image: The M7 charger as packaged, including a USB cable for firmware updates.

  • ToolkitRC M7 Multi-Charger (1 pc)
  • USB Cable (for firmware updates)
  • User Manual

Note: Power supply cables (e.g., XT60 input cable) and battery charging cables are NOT included and must be purchased separately.

4.2 Initial Power-On

  1. Connect a 7-28V DC power supply to the input port on the back of the M7 (e.g., via an XT60 connector). The USB cable alone is for firmware updates and 5V output, not for powering the charger for battery charging.
  2. The display will show the boot logo for 2 seconds, accompanied by a boot sound.
  3. After booting, the screen will enter the main interface, displaying current status (input voltage, temperature, etc.).

4.3 Basic Navigation

  • Auxiliary Functions: Long press the [Exit] button to enter the auxiliary function interface.
  • Page Switching: Rotate the [Scroll Wheel] to switch between different pages or options.
  • Task Selection (Idle): Short press [OK] to select a charging task when the charger is idle.
  • System Settings: Long press [OK] to enter the system setting interface.
  • Confirm/Delete: Short press [Scroll Wheel] to confirm a function. Long press [Scroll Wheel] for 2 seconds to activate the delete key function.
  • Exit/Return: Short press [Exit] to end modifications or return to the previous interface.

5. Operating Instructions

5.1 Charge and Discharge Settings

From the main interface, short press [OK] to enter the charging function. You will see the battery selection menu.

5.1.1 Battery Type Setting

  1. Rotate the [Scroll Wheel] to select an existing battery profile or create a new one (up to 32 profiles).
  2. Press [OK] to enter the battery setting interface.
  3. Move the cursor to 'Battery Type' and press [OK] to select from LiPo, LiHV, LiFe, Lion, NiMh, or PB.

Warning: Always ensure the selected battery type matches the actual battery to prevent damage.

5.1.2 Cell Count Setting

  1. Navigate to 'Cells' and press [OK].
  2. Rotate the [Scroll Wheel] to adjust the cell count (e.g., 1S, 2S, 3S, etc.).
  3. Selecting 'Auto' allows the charger to automatically detect the cell count based on battery voltage.

Tip:

  • If a battery is over-discharged or over-charged, automatic cell detection might be inaccurate. Manually set the correct cell count.
  • For Li-XX batteries, connecting the balance port improves cell count accuracy.

5.1.3 Work Mode

  1. Navigate to 'Mode' and press [OK].
  2. Select from: 'Charge', 'DisCHG' (Discharge), or 'StoCHG' (Storage Charge).
  3. NiMh batteries also offer a 'Cycle' mode.

5.1.4 Discharge Mode (if 'DisCHG' or 'StoCHG' selected)

  1. Navigate to 'Discharge Mode' and press [OK].
  2. Inter (Normal) Mode: Discharges through internal heat consumption (max 3.0A@10W).
  3. Recycle Mode: Recovers power to the input battery (max 10.0A@200W). Requires battery input power.
  4. External Mode: Discharges through an external load connected to the input port (max 10.0A@200W).

5.1.5 Input MaxVoltage (for Recycle Discharge)

Set the maximum input voltage. If the input voltage reaches this value during discharge, the process will stop. Set this to your power supply's highest safe voltage.

5.1.6 End Voltage Setting (TVC)

Adjust the cut-off voltage for single cells. For charging, this is the charge cut-off. For discharging, it's the discharge cut-off. Adjustable in 0.01V steps.

  • Only applicable to LiPo, LiHV, LiFe batteries.
  • Do not modify unless familiar with battery characteristics.

5.1.7 Current Setting

Adjust the 'Charge Current' or 'DisCHG Current' (0.1A steps, up to 10.0A) using the [Scroll Wheel].

Tip:

  • Set charging rate to 1-2C (e.g., for a 2000mAh battery, set 2.0-4.0A).
  • Current settings are only active in their corresponding work mode.

5.1.8 NiMh Setting (PeakV)

When using NiMh batteries, set the negative pressure value (5mV-15mV) for full charge detection.

5.1.9 Cycle Setting (for NiMh)

In 'Cycle' mode, set 'Cycle times' (2-12) and 'Rest time' (2-10 minutes). The charger will follow a discharge-charge pattern.

5.1.10 External Load Setting (for External Discharge)

Set the wattage according to the external load connected.

5.1.11 Smart Battery Setting (for UAV batteries)

If 'UAVbat' is selected, choose 'Drone model' and set 'Max Current' (0.5A to 10A).

5.2 Charge and Discharge Operation

Once settings are configured, connect your battery to the output port and balance port (if applicable).

ToolkitRC M7 Charger with a battery balance lead connected to the balance port

Image: Proper connection of a battery balance lead to the M7 charger.

ToolkitRC M7 Charger screen displaying individual cell voltages during charging

Image: The M7 display showing real-time cell voltages during a charging cycle.

  1. The charger will enter the working interface, displaying real-time data (voltage, current, mAh, individual cell voltages).
  2. Rotate the [Scroll Wheel] to switch between status information, internal resistance, and other details.
  3. Short press [OK] to dynamically adjust the working current or stop the process.
  4. To end, navigate to 'Stop' and press [OK].

Tips:

  • Always supervise charging/discharging.
  • For lithium batteries, connect both main and balance ports for proper balance management.
  • After charging, unplug the battery. The charger will automatically continue with a new battery if set to do so.

5.3 Auxiliary Functions (Accessibility)

From the main interface, long press [Exit] to access auxiliary functions.

5.3.1 Measure Resistance

Select 'Measure resistance' and press [OK] to test the internal resistance of the connected battery.

5.3.2 Measure Signal

Select 'Measure signal' and press [OK]. Choose signal type (PWM, PPM, SBUS) using the [Scroll Wheel] to view real-time signal values.

5.3.3 Signal Output

Select 'Signal output' and press [OK]. Choose signal type (PWM, PPM, SBUS). Set mode (Manual, Auto 1/2/3) and adjust pulse width/cycle as needed.

5.3.4 ESC Test

Select 'ESC test' and press [OK]. Adjust pulse width and cycle to test ESCs.

5.3.5 Power Supply Function

Select 'Power' and press [OK]. Set desired output voltage and current. Press [OK] to start power output.

6. Maintenance

6.1 General Care

  • Keep the device clean and free from dust.
  • Avoid dropping or subjecting the device to strong impacts.
  • Store in a dry place away from direct sunlight and extreme temperatures.

6.2 Firmware Upgrade

  1. Connect the M7 to your computer using the provided USB data cable.
  2. The computer will recognize a U disk named 'Toolkit'.
  3. Download the latest firmware file (e.g., app.upg) from the official ToolkitRC website.
  4. Copy the downloaded file to the 'Toolkit' U disk, overwriting any existing firmware files.
  5. The device will automatically update its firmware.

6.3 Voltage Calibration

In the shutdown state, press and hold the [Scroll Wheel], then connect the power supply. The system will enter manual voltage calibration. Use a voltmeter to measure actual battery voltages and adjust the M7's displayed values to match. Save changes before exiting.

7. Troubleshooting

  • Charger Not Powering On: Ensure the input power supply is within the 7-28V range and correctly connected with proper polarity.
  • Battery Not Charging: Verify the battery type, cell count, and charging current settings are correct. Check battery connections (main and balance ports). Ensure an external power source (XT60) is connected, not just USB.
  • Inaccurate Voltage Readings: Perform voltage calibration as described in the Maintenance section.
  • Display Stuck at 0.12V (No Battery): Some users report the display showing 0.12V instead of 0.00V when no battery is connected. This may be within normal operating specifications for some units and typically does not affect charging accuracy.
  • Balance Terminal Interference: If your battery's balance terminal has a protective cover, it might prevent simultaneous insertion with the XT60 terminal. Adjust the cover or connect carefully.
  • Overheating: Ensure the cooling fan is not obstructed. The fan automatically adjusts speed based on internal temperature.

8. Specifications

CategoryParameterValue
InputVoltage7-28V @MAX12A
Battery TypeLiPo/LiHV/LiFe/Lion (1-6S), NiMh (1-16S), Pb (1-10S)
ChargingBalance Current400mA @2-6S
Accuracy<0.005V
Power0.1-10A @200W
Discharge Power0.1-10A @250W (Recycle Mode)
Internal Discharge Power0.1-3A @12W
USB Output2.1A @5V (upgrade @USB3.0)
BatteryVoltage Range1.0V-5.0V @1-6S
Internal ResistanceMeasurement1-100mR @1-6S
MeasuringPWM880us-2200us @20-400hz
PPM880us-2200us*8 CH @20-50hz
SBUS880us-2200us*16 CH @20-100hz
OutputPWM500us-2500us @20-1000hz
PPM880us-2200us*8 CH @50hz
SBUS880us-2200us*16 CH @74hz
Power Supply Mode1-10A @1-28V (CC+CV)
DisplayTypeIPS 2.0 inch, 320*240 resolution
ProductSize73mm*51mm*27mm
Weight90g
Individual PackingSize84mm*79mm*39mm
Weight150g

9. User Tips

  • Portability: The M7 is highly compact and portable, making it ideal for field use.
  • Quiet Operation: The integrated cooling fan operates effectively and quietly.
  • Intuitive Interface: Users generally find the menu system easy to navigate with a clear display.
  • Excellent Balancing: The charger actively balances individual cells, often resulting in perfectly balanced packs.
  • Versatile Discharge: Utilize the built-in discharge function (max 3A internal) or external/recycle modes for various needs.
  • Servo Testing: The M7 includes a convenient connection for testing servos.
  • Calibration for Accuracy: For optimal accuracy, especially with 6S LiPo batteries, consider performing voltage calibration.
  • Power Source Requirement: Remember that an external DC power source (e.g., XT60 connection) is required for charging; the USB port is primarily for firmware updates and 5V output.

10. Warranty and Support

For warranty information, technical support, and the latest firmware updates, please visit the official ToolkitRC website:

www.toolkitrc.com

You can also scan the QR code provided in the product's original manual for direct access to applications, video tutorials, and product information.

Video: An unboxing and overview of the ToolkitRC M7 Multi-Charger.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.