DM Aurora 2

Contents

DM Aurora 2 Tattoo Power Supply User Manual

Model: Aurora 2 (CP100)

1. Introduction

Thank you for choosing the DM Aurora 2 Tattoo Power Supply. This digital LCD power supply is designed for both coil and rotary tattoo machines, offering an upgraded experience with its intuitive interface and dual output modes. This manual provides essential information for the safe and effective use of your device.

For a comprehensive guide, you may also refer to the official User Manual (PDF).

2. Safety & Warnings

WARNING: Please mind potential fire risk and strictly follow the instruction manual for charging and storage. For disposal, please check your local authority's website for more information and dispose of the lithium-ion battery safely in accordance with the applicable legal requirements.

Important Safety Information:

  • Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
  • Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture.

3. Product Overview

The DM Aurora 2 features a digital LCD screen and intuitive controls for precise voltage adjustment and mode selection.

DM Aurora 2 Tattoo Power Supply labeled diagram
Figure 1: Product Parameter Diagram with Labeled Parts

Key Components:

  • LED Screen: Displays current voltage and mode.
  • Voltage Adjust Up Button: Increases voltage.
  • Voltage Adjust Down Button: Decreases voltage.
  • Left Button: Function button (specific to mode).
  • Right Button: Function button (specific to mode).
  • Footswitch Mode Button: Toggles between momentary and maintained footswitch modes.
  • Tattoo Machine Input: Connect your primary tattoo machine.
  • Power Input: Connect the 5V power adapter.
  • Food Pedal or 2nd Tattoo Machine Input: Connect a foot pedal or a second tattoo machine for dual operation.
DM Aurora 2 Tattoo Power Supply showing built-in magnets
Figure 2: Built-in magnets for easy mounting

The power supply features built-in magnets for convenient mounting on metallic surfaces.

4. Setup

  1. Unpacking: Carefully remove the power supply from its packaging. Remove all protective films from the device.
  2. Power Connection: Connect the provided USB cable to the Power Input port on the back of the Aurora 2. Plug the other end of the USB cable into a certified 5V power adapter (not always included).
  3. Tattoo Machine Connection:
    • For single machine operation: Connect your primary tattoo machine to the 'Tattoo machine input' jack.
    • For dual machine operation: Connect your primary tattoo machine to the 'Tattoo machine input' jack and your second tattoo machine to the 'Food pedal or 2nd tattoo machine input' jack.
  4. Foot Pedal Connection (if applicable): If using a foot pedal in single machine output mode, connect it to the 'Food pedal or 2nd tattoo machine input' jack.

5. Operating Instructions

5.1 Power On/Off

  • To Turn On: Press and hold the power button (center button) for 3 seconds.
  • To Turn Off: Press and hold the power button for 3 seconds.

5.2 Voltage Adjustment

Use the 'Voltage adjust up button' and 'Voltage adjust down button' to set your desired voltage. The Aurora 2 supports a voltage range from 1.5V to 16.0V, indicated by different colored lights on the display.

Voltage display ranges 1.5V-7.0V
Figure 3: Voltage Display Ranges (1.5V - 7.0V)
Voltage display ranges 7.1V-16.0V
Figure 4: Voltage Display Ranges (7.1V - 16.0V)

5.3 Mode Switching (Single vs. Dual Machine Output)

Short press the power button to cycle through different operating modes.

Diagram showing single and dual machine output modes
Figure 5: Innovative Technology of Dual Mode Switching
  • Single Machine Output Mode (LED display 1-0): In this mode, the left jack is connected to the tattoo machine, and the right jack is used for a conventional foot pedal interface control switch.
  • Dual Computer Output Mode (LED display 1-1): In this mode, both the left and right jacks are connected to tattoo machines. Only the key pedal switch (likely referring to the footswitch mode button on the unit itself) can be used in this state.

5.4 Footswitch Mode

Use the 'Footswitch mode button' to switch between momentary and maintained footswitch operation, depending on your preference and tattooing style.

6. Maintenance

  • Cleaning: Wipe the device with a soft, dry cloth. Do not use abrasive cleaners or immerse the unit in water.
  • Storage: After use, turn off the device and store it in a dry place, away from direct sunlight and extreme temperatures. Keep it out of reach of children.
  • Inspection: Regularly inspect the power supply and cables for any signs of damage. Do not use if damaged.

7. Troubleshooting

If you encounter issues with your DM Aurora 2 Tattoo Power Supply, please consider the following:

  • Device not turning on: Ensure the power cable is securely connected to both the power supply and a working 5V power adapter. Confirm the power adapter is receiving power.
  • Inconsistent voltage: Check all connections to your tattoo machine and foot pedal. Ensure the cables are not damaged.
  • Machine not running: Verify the power supply is on and set to the correct voltage. Check the connection of your tattoo machine. If using a foot pedal, ensure it is functioning correctly or try switching to a different footswitch mode.

If problems persist, please contact customer support.

8. Specifications

Feature Specification
Product Name Tattoo Power Supply
Model CP100 (Aurora 2)
Input Voltage 5V
Output Voltage Range 1.5V - 16.0V
Display Digital LCD
Batteries Included Yes
Certification 3C
Origin Mainland China
Package Length 18 cm
Package Width 12 cm
Package Height 8 cm
Package Weight 0.49 kg

9. User Tips

  • The Aurora 2 is designed to be easy to use, making it suitable for various users.
  • Utilize the built-in magnets for convenient placement on metal surfaces in your workspace.
  • Remember to remove all protective films before the first use for optimal display clarity.

10. Frequently Asked Questions (FAQ)

Q: Is the power adapter included with the Aurora 2 Tattoo Power Supply?
A: The product includes a USB cable for charging. You will need to connect it to a certified 5V power adapter, which may not be included with the unit.

11. Manufacturer & Support Information

Manufacturer:

Yiwu Longman E-commerce Co., Ltd
Room 1011, Floor 10, Block A, Wanda Plaza, the Pearl River Street,
Yiwu, Zhejiang, China
Phone: 86-18069918600
Email: dmtattoosupply@126.com

EU Authorized Representative:

APEX CE SPECIALISTS LIMITED
UNIT 3D NORTH POINT HOUSE NORTH POINT BUSINESS PARK
NEW MALLOW ROAD CORK T23 AT2P, IRELAND
Phone: +35-3212066339
Email: info@apex-ce.com

For further assistance or inquiries, please contact the manufacturer or authorized representative directly.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.