ToolKitRC ADP200

Contents

ToolKitRC ADP200 Power Supply Adapter User Manual

Model: ADP200

1. Introduction

The ToolKitRC ADP200 is a high-performance AC to DC power supply adapter designed to provide stable and reliable power for various RC chargers and other compatible electronic devices. With a robust 200W output, it ensures efficient operation for your equipment.

For a more detailed guide, you may refer to the official user manual in PDF format: ToolKitRC ADP200 User Manual (PDF)

2. Safety Information

Please read and understand all safety warnings before using this product to prevent injury or damage to the device.

  • WARNING: This device may not cause harmful interference.
  • This device must accept any interference received, including interference that may cause undesired operation.
  • Pay attention to the output voltage to prevent damage to the connected device.
  • Do not use this product unattended.
  • CHOKING HAZARD: Small parts. Not for children under 3 years.
ToolKitRC ADP200 power adapter rear label with specifications and warnings

Rear view of the ToolKitRC ADP200 power adapter showing detailed specifications, warnings, and certifications.

3. Package Contents

Upon opening the package, please verify that all items are present and in good condition:

  • ToolKitRC ADP200 Power Supply Adapter
  • AC Power Cord (region-specific)

An unboxing video of the ToolKitRC ADP200 power supply adapter, showing its contents and initial appearance.

4. Setup

Follow these steps to set up your ADP200 power supply:

  1. Connect the provided AC power cord to the input port on the ADP200 adapter.
  2. Plug the other end of the AC power cord into a suitable wall outlet (AC 100-240V, 50/60Hz).
  3. Connect the XT60 output connector of the ADP200 to your compatible RC charger or device. Ensure the XT60 connector is fully seated and correctly oriented.
ToolKitRC ADP200 power adapter with input and output voltage labels

Diagram showing the input and output voltage ports of the ToolKitRC ADP200 power adapter.

5. Operating Instructions

The ToolKitRC ADP200 is designed for straightforward operation:

  1. Once connected as per the setup instructions, the ADP200 will provide a stable DC 19.5V output through its XT60 connector.
  2. Ensure your connected device is compatible with the output voltage (DC 19.5V) and current (up to 10.3A) of the ADP200.
  3. Monitor your connected device for proper function. The ADP200 is designed to operate with low heat output under normal loads.
  4. When finished, disconnect the XT60 output from your device, then unplug the AC power cord from the wall outlet.

6. Maintenance

To ensure the longevity and optimal performance of your ADP200 power supply, follow these simple maintenance guidelines:

  • Keep the adapter clean and free from dust. Use a soft, dry cloth for cleaning.
  • Avoid exposing the adapter to moisture, water, or extreme temperatures.
  • Do not attempt to open the casing or modify the adapter, as this will void the warranty and may cause damage or injury.
  • Store the adapter in a cool, dry place when not in use.

7. Troubleshooting

If you encounter issues with your ADP200 power supply, try the following troubleshooting steps:

  • No Power Output:
    • Ensure the AC power cord is securely connected to both the adapter and the wall outlet.
    • Check if the wall outlet is functional by plugging in another device.
    • Verify that the XT60 output connector is properly connected to your device.
  • Device Not Charging/Operating Correctly:
    • Confirm that your device's input voltage and current requirements match the ADP200's output (DC 19.5V, 10.3A).
    • Check your device's manual for specific power requirements.
    • Ensure there are no loose connections.
  • Overheating:
    • Ensure the adapter is used in a well-ventilated area.
    • Verify that the load on the adapter does not exceed its maximum output (200W).

If problems persist, please contact ToolKitRC customer support.

8. Specifications

FeatureSpecification
ModelADP200
Input VoltageAC 100-240V
Input Frequency50-60Hz
Max Input Current4.0A
Output VoltageDC 19.5V
Output Current10.3A
Output ConnectorXT60
Max Output Power200W
Dimensions (L x W x H)219mm x 133mm x 53mm
Weight0.665 kg
MaterialPlastic (ABS)
CertificationsCE, FCC, RoHS

9. User Tips

Based on user experiences, here are some helpful tips for using your ADP200:

  • Users report stable voltage output and low heat generation, even under significant loads.
  • The ADP200 is confirmed to work very well with various smart chargers, including ToolkitRC M8P and is a perfect match for the Q6 Lite charger.
  • Some users have observed the input voltage showing around 20.5V when connected to certain chargers like the M9, indicating efficient power delivery.

10. Warranty and Support

ToolKitRC products are manufactured to high-quality standards. For warranty information, technical support, or service inquiries, please refer to the official ToolKitRC website or contact your authorized dealer.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.