HANDIF MXT Series

Contents

Weller MXT Series Soldering Iron Tip User Manual

Model: MXT Series (Compatible with C245/C210/CLL5/ET/LT/900/T12 series soldering stations)

Brand: HANDIF

1. Product Overview

The Weller MXT Series Soldering Iron Tips are designed for precision soldering tasks, offering high quality and smooth soldering performance. These tips are constructed with a multi-layer electroplating process for enhanced anti-oxidation and corrosion resistance, ensuring durability and consistent performance. They are compatible with WELLER WSD71, WSDT1, and WP70 soldering stations.

Assortment of Weller MXT Series Soldering Iron Tips, showcasing various tip shapes.

Figure 1: Assortment of Weller MXT Series Soldering Iron Tips, showcasing various tip shapes.

Multiple Weller MXT Series Soldering Tips, illustrating the range of available models to meet diverse soldering requirements.

Figure 2: Multiple Weller MXT Series Soldering Tips, illustrating the range of available models to meet diverse soldering requirements.

Video 1: Demonstration of the Weller MXT Series Soldering Iron Tip in action, highlighting its performance and ease of use.

2. Safety & Warnings

Read all instructions carefully before use to ensure safety and prevent damage to the product or injury to the user.

Warning: Keep the device and its cord out of reach of children under 3 years old.

2.1 Soldering Safety

  • Always wear protective eyewear when operating a soldering station.
  • Ensure good ventilation in the work area to prevent inhalation of flux fumes.

2.2 Usage Environment

  • The soldering station must be properly grounded to prevent static electricity damage, especially when working with sensitive electronic components.

3. Setup

3.1 Soldering Station and Soldering Iron Tip Usage Steps

  1. Settings and Preheating: Connect the soldering station to power and turn it on. Set the appropriate temperature, typically between 300°C and 380°C. Adjust the temperature based on the solder type: 330-370°C for leaded solder, and 350-400°C or higher for lead-free solder.
  2. Cleaning and Tinning: Before use, clean the soldering iron tip on a damp sponge or with a metal scouring pad. After preheating, melt solder wire onto the tip to apply a thin layer of tin. This process, known as "tinning," prevents oxidation and improves heat conduction.

4. Operating Instructions

4.1 Soldering Operation

  1. Simultaneously contact the soldering iron tip with both the component lead and the PCB pad.
  2. Heat the joint for approximately 1-2 seconds.
  3. Feed in the solder wire.
  4. Once the solder melts and wets the pad, remove the solder wire.
  5. Finally, remove the soldering iron tip to allow the solder joint to cool naturally.

4.2 Tip Selection

Different soldering iron tip shapes are suitable for various applications:

  • Knife-edge tips: Ideal for drag soldering.
  • Pointed tips: Best suited for small components and fine work.
  • Other shapes like horseshoe tips are also available for specific tasks.

5. Maintenance

5.1 Daily Maintenance and Care of the Soldering Iron Tip

  • Preventing Oxidation: Avoid dry-heating the soldering iron tip for extended periods at excessively high temperatures, as this accelerates oxidation.
  • Cleaning Method: Never use abrasive tools like files or sandpaper to clean the soldering tip. Always use a dedicated sponge or brass wool.
  • Maintenance (during use): When the soldering station is not in use for extended periods, ensure the soldering iron tip is tinned and the station is put into sleep mode.

5.2 General Maintenance & Storage

  • Cleaning: Turn off the device before cleaning. Use a soft, lint-free cloth to wipe the exterior.
  • Storage: Store the soldering tips in a dry place at room temperature (15°C - 35°C).

6. Troubleshooting

  • Oxidized/Blackened Tip: If the soldering iron tip becomes oxidized and blackened, preventing it from accepting solder, it can often be repaired using a special "soldering iron tip revival paste."
  • Loss of Solderability: The soldering iron tip is a consumable item. If surface wear or structural changes cause it to lose its ability to accept solder, it should be replaced promptly.

7. Specifications

7.1 General Specifications

AttributeValue
Product NameSOLDERING TIP
Brand NameHANDIF
OriginMainland China
High-concerned chemicalNone
Compatible StationsWELLER WSD71, WSDT1, WP70
Batch Number1155998324#

7.2 Tip Construction

Diagram illustrating the multi-layer electroplating process of the soldering tip, featuring a plating layer, nickel plating, iron plating, oxygen-free copper core, and the working surface, designed for anti-oxidation and corrosion resistance.

Figure 4: Diagram illustrating the multi-layer electroplating process of the soldering tip, featuring a plating layer, nickel plating, iron plating, oxygen-free copper core, and the working surface, designed for anti-oxidation and corrosion resistance.

  • Core Material: Oxygen-free Copper
  • Layers: Iron plating, Nickel plating, Plating layer (for anti-oxidation and corrosion resistance)

7.3 Dimensional Specifications (Examples)

Dimensional specifications for MXT F (1.2mm conical), MXT AA (1.6mm conical), MXT BB (2.4mm chisel), and MXT CC (3.2mm chisel) tips. All tips feature a 12mm cone length and a 22mm shaft length.

Figure 5: Dimensional specifications for MXT F (1.2mm conical), MXT AA (1.6mm conical), MXT BB (2.4mm chisel), and MXT CC (3.2mm chisel) tips. All tips feature a 12mm cone length and a 22mm shaft length. (Note: Dimensions are for reference, actual product may vary slightly).

Dimensional specifications for MXT B (2.4mm chisel) tip, with a total length of 33mm.

Figure 6: Dimensional specifications for MXT B (2.4mm chisel) tip, with a total length of 33mm. (Note: Dimensions are for reference, actual product may vary slightly).

Dimensional specifications for MXT KN (4.7mm blade, 2.0mm thick) tip, with a 12mm blade length and 22mm shaft length.

Figure 7: Dimensional specifications for MXT KN (4.7mm blade, 2.0mm thick) tip, with a 12mm blade length and 22mm shaft length. (Note: Dimensions are for reference, actual product may vary slightly).

ModelTip TypeTip Width/DiameterCone LengthShaft LengthTotal Length
MXT FConical1.2 mm12 mm22 mm~34 mm
MXT AAConical1.6 mm12 mm22 mm~34 mm
MXT BBChisel2.4 mm12 mm22 mm~34 mm
MXT CCChisel3.2 mm12 mm22 mm~34 mm
MXT BChisel2.4 mm--33 mm
MXT KNBlade4.7 mm (2.0 mm thick)12 mm22 mm~34 mm

8. User Tips

  • Always ensure your soldering station is at the correct temperature for the solder type you are using to achieve optimal joints and prevent tip damage.
  • Regularly clean and tin your soldering tip to extend its lifespan and maintain efficient heat transfer.
  • When working with different component sizes or soldering techniques, select the appropriate tip shape for best results.
  • Keep a soldering iron tip revival paste handy for minor oxidation issues to restore tip functionality.

9. Disposal & Recycling

This product is marked with the WEEE symbol, indicating that it should not be disposed of with household waste.

According to the WEEE Directive (2012/19/EU), this product must be disposed of at an appropriate electronic waste collection point for recycling. Proper disposal helps prevent potential negative consequences for the environment and human health.

10. Manufacturer & Support Information

Manufacturer: Shenzhen Handifeng Technology Co., Ltd.

Manufacturer Contact: sales17@handif.com

EU Authorized Representative: VAT SPEED SL

Address: Calle Antonio Salvador N99.1, 28026 Madrid, Spain

EU Representative Contact: services@vatspeed-eu.com

For a detailed user manual in PDF format, please refer to the official document available at: Weller MXT Series Soldering Iron Tip User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.