1. Introduction
This manual provides detailed instructions for the safe and efficient operation of your BAOFENG UV18 Pro Max GPS Walkie Talkie. Please read this manual thoroughly before using the device to ensure proper functionality and to prevent damage or injury.
The UV18 Pro Max is a versatile six-band handheld transceiver featuring GPS, AM/FM radio, NOAA weather reception, wireless frequency copy, and a 1.77-inch LED display. It is designed for a wide range of communication needs, offering robust performance and advanced features.
2. Safety and Regulatory Information
2.1 FCC Regulatory Conformance
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Verification of harmful interference by this equipment to radio or television reception can be determined by turning it off and then on. The user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.
WARNING! MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.
2.2 Compliance with RF Exposure Standards
The radio complies with the following RF energy exposure standards and guidelines:
- United States Federal Communications Commission, Code of Federal Regulations; 47 CFR § 1.1307, 1.1310 and 2.1093
- American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005; Canada RSS102 Issue 5 March 2015
- Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005 Edition
2.3 RF Exposure Compliance and Control
Guidelines and Operating Instructions
To control your exposure and ensure compliance with the occupational/controlled environmental exposure limits, always adhere to the following procedures.
Guidelines:
- Do not remove the RF Exposure Label from the device.
- User awareness instructions should accompany device when transferred to other users.
- Do not use this device if the operational requirements described herein are not met.
Operating Instructions:
- Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), press the Push-to-Talk (PTT) key. To receive calls, release the [PTT] key. Transmitting 50% of the time, or less, is important because the radio generates measurable RF energy only when transmitting (in terms of measuring for standards compliance).
- Keep the radio unit at least 2.5cm away from the face. Keeping the radio at the proper distance is important as RF exposure decreases with distance from the antenna. The antenna should be kept away from the face and eyes.
- When worn on the body, always place the radio in an approved holder, holster, case, or body harness or by use of the correct clip for this product. Use of non-approved accessories may result in exposure levels which exceed the FCC's occupational/controlled environmental RF exposure limits.
- Use of non-approved antennas, batteries, and accessories causes the radio to exceed the FCC RF exposure guidelines.
- Contact your local dealer for the product's optional accessories.
2.4 Precautions for Portable Terminals
To protect you against any property loss, bodily injury or even death, be sure to observe the following safety instructions:
- Do not operate the product in a location containing fuels, chemicals, explosive atmospheres and other flammable or explosive materials. In such location, only an approved Ex-protection model is allowed for use, but any attempt to assemble or disassemble it is strictly prohibited.
- Do not operate the product near or in any blasting area.
- Do not operate the product near any medical or electronic equipment that is vulnerable to RF signals.
- Do not hold the product while driving.
- Do not operate the product in any area where use of wireless communication equipment is completely prohibited.
Important Tips
To help you make better use of the product, be sure to observe the following instructions:
- Do not use any unauthorized or damaged accessory.
- Keep the product at least 2.5 centimeters away from your body during transmission.
- Do not keep the product receiving at high volume for a long time.
- For vehicles with an air bag, do not place the product in the area over the air bag or in the air bag deployment area.
- Keep the product and its accessories out of reach of children and pets.
- Please operate the product within the specified temperature range.
- Continuous transmission for a long time may lead to heat accumulation within the product. In this case, please keep it at a proper location for cooling.
- Handle the product with care.
- Do not disassemble, modify or repair the product and its accessories without authorization.
2.5 Precautions for Batteries
Charging Prohibitions
To protect you against any property loss, bodily injury or even death, be sure to observe the following safety instructions:
- Do not charge or replace your battery in a location containing fuels, chemicals, explosive atmospheres and other flammable or explosive materials.
- Do not charge your battery that is wet. Please dry it with a soft and clean cloth prior to charge.
- Do not charge your battery suffering deformation, leakage and overheat.
- Do not charge your battery with an unauthorized charger.
- Do not charge your battery in a location where strong radiation is present.
- Overcharge shall always be prohibited for it may shorten the life of your battery.
Maintenance Instructions
To help your battery work normally or prolong its life, be sure to observe the following instructions:
- Accumulated dust on charging connector may affect normal charging. Please use a clean and dry cloth to wipe it on a regular basis.
- It is recommended to charge the battery under 5°C~40°C. Violation of the said limit may cause battery life reduction or even battery leakage.
- To charge a battery attached to the product, turn it off to ensure a full charge.
- Do not remove the battery or unplug the power cord during charging to ensure a smooth charging process.
- Do not dispose of the battery in fire.
- Do not expose the battery to direct sunlight for a long time nor place it close to other heating sources.
- Do not squeeze and penetrate the battery, nor remove its housing.
Transportation Instructions
- Damaged batteries must not be transported.
- To avoid short circuit, separate the battery from metal parts or from each other if two or more batteries are transported in one packaging.
- The radio must be switched off and secured against switch-on, if the battery is attached.
The content of the shipment must be declared in the shipping documents and by a Battery Shipping Label on the packaging. Contact your hauler for the local regulations and further information.
3. Package Contents
This transceiver comes shipped with the following items in the box:
- 1 Radio body
- 1 Lithium-Ion battery pack
- 1 Instruction Manual
- 1 Belt Clip
- 1 Antenna
- 1 Desk charger (With wall-wart)
- 1 Wrist Belt
- 1 USB-C Charger
*If any item is missing, please notify your Baofeng / Pofung dealer.

4. Product Features
- 1.77" TFT large screen, full keyboard, fully open menu operation
- Scanner function: VFO scan range setting, three scan recovery methods, channel scan, CTC/DCS scan, scan channel addition and removal
- 108-136, 136-174, 220-260, 350-390, 400-520MHz Multiband scanning receiver
- Built-in input method, allows this device to edit channel name
- NOAA Weather Radio Channel Reception in the United States and Canada
- Frequency step, selectable between 2.5K | 5.0K | 6.25K | 10.0K | 12.5K | 20.0K | 25.0K | 50.0K
- Type-C direct charging and charging stand, more convenient battery life
- Dual-band handheld transceiver.
- High Capacity Lithium-Ion battery.
- 50 CTCSS tones and 105 DCS codes.
- 10 zones storage, Up to 1000 named memory channels.
- High or low power selectable.
- Function beep on the keyboard.
- Programmable repeater offset.
- Transmission time-out timer.
- Busy channel lock out.
- LED flashlight.
- Ten (10) levels of Squelch adjustment.
- End of transmission tone, aka "Roger Beep".
- Two (2) pins for Kenwood accessory port
- DTMF encoder and DTMF manual dial
- Broadcast FM radio receiver 78-108 MHz
- VOX (voice activated transmit).
- Alarm function.
- Display illumination programmable via keypad.
- Dual watch / Dual reception.
- Battery saving function.
- Scan mode.
- Built in CTCSS/DCS tones.
- PC programmable.
- Cross band reception.
- One touch search frequency


5. Radio Overview

- Antenna
- Flashlight/ Emergency Alert key
- PTT key
- SK2 key (Customization key)
- MENU key
- Numeric keypad
- Power / Volume knob
- Color LCD
- Speaker/Mic Jacks
- MIC Input
- Exit Key
- Up or Down navigation keys
- Battery pack
- Type-C charging port
- Battery tightening screw
- Type-C charging indicator
- LED flashlight
- LED Status Indicator
5.1 Status Indications
The top LED will help you to identify the current radio status.
| LED Indication | What it Indicates |
|---|---|
| Constant Green | Receiving Signal |
| Constant Red | Transmitting signal |
| Flashes Green | Monitor mode/Scanning Receiving |
5.2 LCD Icon Summary
| Icon | Description |
|---|---|
| RSSI | Operating band signal |
| H | Transmit power level indicator, According to Power High |
| L | Transmit power level indicator, According to Power Low |
| ♪ | Make sure you can hear the DTMF side tone from the radio speaker, set to DT-ST, ANI-ST, DT+ANI. |
| D | DCS enabled |
| C | CTCSS enabled |
| + | Enables access of repeaters in VFO/Frequency Mode. TX will be shifted higher in frequency than RX. |
| - | Enables access of repeaters in VFO/Frequency Mode. TX will be shifted lower in frequency than RX. |
| D | Dual watch enabled |
| Key icon | Keypad lock enabled |
| Speech bubble icon | VOX enabled |
| Shield icon | The confidential calling feature is activated |
| N | Narrowband enabled |
| Battery icon | Battery level indicator |
6. Setup and Preparation
6.1 Battery Information
Charging the Battery Pack
The Li-ion battery pack is not charged at the factory; please charge it before use. Charging the battery pack for the first time after purchase or extended storage (more than 2 months) may not bring the battery pack to its normal maximum operating capacity. Best operation will require fully charging/discharging the battery two or three times before the operating capacity will reach its best performance. The battery pack life may be depleted when its operating time decreases even though it has been fully and correctly charged. If this is the case, replace the battery pack.
Please use the specified charger provided by Baofeng. Other models may cause explosion and personal injury. After installing the battery pack, and if the radio displays low battery with a red flashing lamp or voice prompt, please charge the battery.
Use Caution with the Li-ion Battery
- Do not short the battery terminals or throw the battery into a fire. Never attempt to remove the casing from the battery pack, as Baofeng cannot be held responsible for any accident caused by modifying the battery.
- The ambient temperature should be between 5°C-40°C (40°F-105°F) while charging the battery. Charging outside this range may not fully charge the battery.
- Please turn off the radio before inserting it into the charger. It may otherwise interfere with correct charging.
- To avoid interfering with the charging cycle, please do not cut off the power or remove the battery during charging until the green light is on.
- Do not recharge the battery pack if it is fully charged. This may shorten the life of the battery pack or damage the battery pack.
- Do not charge the battery or the radio if it is damp. Dry it before charging to avoid damage.
How to Charge
- Plug the AC adaptor into the AC outlet, and then plug the cable of the AC adaptor into the DC jack located on the back of the charger. The indicator light blinks orange and is then ready to charge battery.
- Plug the battery or the radio into the charger. Make sure the battery terminals are good in contact with charging terminals. The indicator light turns to red--- charging begins.
- It takes approximately 2-5 hours to fully charge the battery. When the lamp lights green, the charging is completed. Remove the battery or the radio unit with its battery from socket.
NOTICE: When charging a radio (with battery) the indicating lamp will not turn into green to show the fully charged status if the radio is powered on. Only when the radio is switched off will the lamp indicate normal operation. The radio consumes energy when it is power-on, and the charger cannot detect the correct battery voltage when the battery has been fully charged. So the charger will charge the battery in constant voltage mode and fail to indicate correctly when the battery has been fully charged.
LED Indicator during Charging
| Red LED | Green LED | Status |
|---|---|---|
| Flashing | Steady | Standby (charger empty) / Error (charger with radio) |
| Steady | Off | Charging |
| Off | Steady | Charge complete. |
Using the Type-C Charger
The Type-C charger is a handy port that allows you to conveniently charge your Li-ion battery pack.
- Make sure your radio is turned OFF.
- Plug the Type-C cable into the Type-C charging port on your battery. Connect the other end of the Type-C charger to wall power outlet.
- An empty battery will be fully charged in 6 hours.
- The battery meter on LCD will move to indicate the battery is charging.
Prolonging the life of your battery
- Only charge batteries in normal room temperatures.
- When charging a battery attached to the radio, turn the radio off for a faster charge.
- Do not unplug the power to the charger or remove the battery and/or radio before it's finished charging.
- Never charge a wet battery.
- Batteries wear out over time. If you notice a considerably shorter operating time with your radio, please consider purchasing a new battery.
How to Store the Battery
- If the battery needs to be stored, keep it in status of 80% discharged.
- It should be kept in low temperature and dry environment.
- Keep it away from hot places and direct sunlight.
- To avoid severe capacity degradation of your battery while in long-term storage, please cycle the battery at least every six (6) months.
NOTICE:
- Do not short circuit the battery terminals.
- Never attempt to remove the casing from the battery pack.
- Never store the battery in unsafe surroundings, as a short may cause an explosion.
- Do not put the battery in a hot environment or throw it into a fire, as it may cause an explosion.
6.2 Installing / Removing Components
Installing / Removing the Battery
Installing the Battery Pack:
- Position the battery pack over the back of the radio.
- Engage the battery pack into the radio until battery pack is fully seated into the radio housing.
- Tighten the screws using a coin or at object to secure the battery pack to the radio. Do not overtighten.
To Remove Battery Pack from Radio:
- Loosen the screws on the back of the battery pack.
- Lift the bottom of the battery pack slightly to remove it from the radio housing.
- Pull the battery pack out of the radio housing.
NOTE: The Li-ON battery pack can also be charged in the battery charger.
Installing / Removing the Antenna
- Installing the Antenna: Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure.
- Removing the Antenna: Turn the antenna counter-clockwise to remove it.

Installing / Removing the Belt Clip
- Installing the Belt Clip: Place the belt clip above the corresponding holes on the back of the radio, and screw it into place clockwise with the two supplied screws.
- Removing the Belt Clip: Unscrew counter-clockwise to remove the belt clip.
Installing Additional Speaker/Microphone (Optional)
Pry open the rubber MIC-Headset jack cover and then insert the Speaker / Microphone plug into the double jack.
7. Basic Operations
7.1 Power On/Off and Volume Adjustment
Turning the unit on
To turn the unit on, simply rotate the Volume/Power knob clockwise until you hear a "click". If your radio powers on correctly there should be an audible double beep after one second and the display will show a message or flash the LCD depending on settings for about one second. Then it will display a frequency or channel. If the Voice prompt is enabled, the voice will announce "frequency mode" or "channel mode".
Turning the unit off
Turn the Volume/Power knob counter-clockwise all the way until you hear a "click". The unit is now off.
Adjusting the volume
To turn up the volume, turn the volume/power knob clockwise. To turn the volume down, turn the Volume/Power knob counter-clockwise. Be careful not to turn it too far, as you may inadvertently turn your radio off. By using the monitor function, enabled from the [FM broadcast/Monitor] key below the PTT, you can more easily adjust your volume by adjusting it to the un-squelched static.
7.2 Main Keypad Controls
- MENU key: Used for activating the MENU, choosing each MENU selection, and confirming the parameter. In standby mode, press and hold the key to switch between frequency (VFO) mode and channel (MR) mode. When listening to broadcast FM, the key switches between 65-75 MHz and 76-108 MHz bands.
- Up arrow key: Press it for more than 2 seconds, the channel and frequency will move upwards rapidly; in SCAN mode, press this control to move the scanning upwards.
- Down arrow key: Keep it pressed it for more than 2 seconds, the channel and frequency will move downwards rapidly; in SCAN mode, press this control to move the scanning downwards.
- EXIT key: Press to exit the Menu and functions.
- Numeric keypad: With these keys you can input the information or your selections on the radio. In TX mode, push the number keys to send a corresponding DTMF code.
- * Key: A short momentary press of the key enables the reverse function. The radios features a keypad lock that locks out all keys except for the three side keys. To enable or disable the keypad lock, press and hold the key for about two seconds.
- #z key: When listening to broadcast FM a momentary press will start the scanning. Scanning in broadcast FM will stop as soon as an active station is found, regardless of scanner resume method. To enable the scanner, press and hold the #z key for about two seconds. Short press the #z key to quickly enter the DTMF dialing.
7.3 Band and Channel Selection
Main Band/Sub Band Switch
In standby mode, press the [A/B] key to switch between the main frequency band or sub frequency bands. The highlighted frequency band is the main frequency band, and the dimmed frequency band is the sub frequency band.
VFO/Channel Switch
Press and hold the [VFO/MR] key to switch between VFO and channel display.
- In channel mode (MR), the channel number will be displayed on the right.
- In frequency mode (VFO), the 'VFO' will be displayed on the right.
Frequency (VFO) mode
In Frequency (VFO) mode you can navigate up and down the band by using the Up or Down keys. Each press will increment or decrement your frequency according to the frequency step you've set your transceiver to. You can also input frequencies directly on your numeric keypad with kilohertz accuracy.
Example: Entering the frequency 436.61250 MHz on display A
- In standby mode, press and hold the [VFO/MR] key to switch to the frequency (VFO) mode.
- Enter [4][3][6][6][1][2][5] [0] on the numeric keypad.
WARNING! Just because you can program in a channel does not mean you're automatically authorized to use that frequency. Transmitting on frequencies you're not authorized to operate on is illegal, and in most jurisdictions a serious offence. However, it is legal in most jurisdictions to listen. Contact your regulatory body for further information on what laws, rules and regulations apply to your area.
Channel (MR) mode and Channel selection
There are two modes of operation: Frequency (VFO) mode, and Channel or Memory (MR) mode. For everyday use, Channel (MR) mode is going to be a whole lot more practical than Frequency (VFO) mode.
In Channel (MR) mode you can navigate up and down the channel by using the Up or Down keys or the encoder. Ultimately which mode you end up using will depend entirely on your use case. Press and hold [VFO/MR] key to switch the radio between VFO and Channel mode, select Channel mode.
- Operation 1: Press the Up or Down navigation key to select the channel.
- Operation 2: Input the channel numbers by the keyboard. For example, if you want switch to channel 12, input [0][1][2] a total of 3 digits, and it will switch to channel 12.
When the voice prompt function is enabled, the corresponding channel will be broadcast by voice.
Selecting a Bank
A bank is a group of channels with the same property. The radio supports up to 10 banks, with a maximum of 100 channels per bank. To select a bank, do one of the following: Press [MENU] key go to Menu > Bank, press Up or Down navigation key to select a bank, and then press [MENU] key to switch to the selected bank. The corresponding regional alias will be displayed at the bottom of the screen.
7.4 Communication Functions
Making a call
NOTE: Press the [A/B] key to switch the main channel to the other channel if there are 2 channels shown on the display. In standby mode, press and hold the [VFO/MR] key to switch between frequency (VFO) mode and channel (MR) mode.
- Channel mode call: After selecting a channel, hold down the [PTT] key to initiate a call to the current channel. Speak into the microphone with normal tone. Making a call, the red LED is on.
- Frequency mode call: Press and hold the [VFO/MR] key to switch to the frequency mode, input the working frequency within the allowable frequency range, and press and hold the [PTT] key to transmit on the current frequency. Speak into the microphone with normal tone. Making a call, the red LED is on.
- Receive a call: When you release the [PTT] key, you can answer it without any action.
When receiving a call, the green LED is on. NOTE: To ensure the best reception volume, keep the distance between the microphone and the mouth at the time of transmission from 2.5 cm to 5 cm.
Using the Flashlight
You can use this radio in an emergency. If you press the Flashlight/Emergency Alert key, the radio turns on the high-intensity LED flashlight on your radio.
- Your radio operates normally when the emergency strobe is activated.
- Press the Flashlight/Emergency Alert key once, it will turn on continuously (Always On mode).
- And then, press the Flashlight/Emergency Alert key once, the Strobe Light emits the emergency signal (Strobe emergency mode).
- And then, press the Flashlight/Emergency Alert key once, the light will be turned off.
Emergency Alert
The Emergency Alert feature can be used to signal members in your group for help. To activate the emergency alert function, press and hold the Flashlight/Emergency Alert key for 3 seconds. The radio will send out a loud siren sound and the flashlight will flash. Press the Flashlight/Emergency Alert key to exit the emergency alert function.
WARNING: The Emergency Alert feature should only be used in the event of an actual emergency.
FM Radio (FM)
The [SK2] key of the radio is defined as the FM radio on/off. The frequency ranges to listen to the radio is 65-108MHz. When listening to broadcast FM, press [A/B] key switches between 65-75 MHz and 76-108 MHz band.
- In frequency or channel mode, Press [SK2] key to turn on the radio.
- Select the desired radio frequency with the Up or Down keys or input the frequency.
- Press #z to automatically search a radio station.
- Press [SK2] key to exit FM radio.
Note: while you are listening to the radio, the frequency or channel of A / B receiving signal will automatically switch to the frequency or channel mode for normal transmitting and receiving. When the signal disappears the radio will automatically switch again to FM radio mode.
Monitor
In standby, press and hold the [SK2] key to enter Monitor. When receiving matched carrier but the signaling or the signal is too weak, this function allows monitor the weak signal. Stop pressing the [SK2] key to turn off the speakers and return to standby mode. If no signal, it will emit noise when press the [SK2] Key.
Keypad lock
The radio features a keypad lock that locks out all keys except for the three side keys. To enable or disable the keypad lock, press and hold the * key for about two seconds. You can also enable so that the radio automatically locks the keypad after ten seconds from the menu.
Frequency reversal
A short momentary press of the * key enables the reverse function. If you for some reason want to listen to the repeater's input frequency instead, press * key momentarily and you'll reverse your transmit and receive frequencies.
TX Repeaters tone
Press [PTT] + * key to send 1750Hz repeaters tone. This function is useful for communications through repeaters. If you have the keypad lock enabled on your radio, you can still send a 1750Hz tone the regular way without having to unlock your radio.
Weather Radio/Scan Weather Channel
Your radio has a NOAA Weather Radio function, to enable the user to receive weather reports from designated NOAA stations. Your radio also has a NOAA Weather Scan function, to enable the user to scan all 10 channels of the NOAA Weather Radio.
- To turn the NOAA Weather Scan on, press and hold the [0] key for 3 seconds, a cloud icon appears. The radio will go to Weather band mode.
- Press and hold the #z key for 3 seconds to start automatic scanning of all 10 channels and stop on active channels. Pressing and holding the #z key for 3 seconds during a NOAA weather scan will stop the scan.
- After stopping NOAA weather scan, it is allowed to manually select the weather channel by press the Up or Down key.
- To exit the Weather Radio broadcast mode, press the [EXIT] key or [PTT] key.

Weather channel frequencies and names:
| Channel Number | RX Frequency MHz | Channel Number | RX Frequency MHz |
|---|---|---|---|
| CH-01 | 162.550 | CH-06 | 162.500 |
| CH-02 | 162.400 | CH-07 | 162.525 |
| CH-03 | 162.475 | CH-08 | 161.650 |
| CH-04 | 162.425 | CH-09 | 161.775 |
| CH-05 | 162.450 | CH-10 | 163.275 |
NOTE: Weather Channels Wx 1 Thru 10, Receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.
One touch frequency Search
- Through the CPS program software or the radio menu >> Radio Setting >> Press the SK2 key to define the SK2 side key as a Search function.
- The radio will act as a receiver. Briefly press the preset" Search "key, and the screen will display "SEARCH SEEK..."
- If the transmitter continues to transmit and the unit receives an effective frequency (the strongest and stable signal), the received frequency will be displayed. If there is a CTCSS or DCS, the CTCSS or DCS value is displayed, and if there is no CTCSS or DCS, NONE is displayed.
- You can press the MENU key to save the Search frequency and CTCSS or DCS to the channel.
Note: During frequency Search, press the # key on the radio to switch between UHF or VHF bands.
8. Advanced Features
8.1 Scanner
The radios features a built in scanner for the VHF and UHF bands. When in Frequency (VFO) mode it will scan in steps according to your set frequency step. In Channel (MR) mode it will scan your channels. To enable the scanner, press and hold the #z key for about two seconds. You can change the scanning direction with the Up or Down keys. Press and hold the #z key to exit scanning mode.
Frequency Ranger
In frequency mode, the frequency sweep range can be precisely set. Input the start value and end value of the sweep frequency through the keyboard. EX: Enter 144146, in frequency mode, scan in the range of 144.000-146.000MHZ. Enter 430440, in frequency mode, scan in the range of 430.000-440.000MHZ. Note: for VFO frequency Ranger, see Menu>SCAN>Freq Ranger.
Scan modes
The scanner is configurable to one of three ways of operation: Time, carrier or search, each of which is explained in further details in their respective section below.
- Time operation (TO) mode: The scanner stops when it detects a signal, and after a factory preset time out, it resumes scanning.
- Carrier operation (CO) mode: The scanner stops when it detects a signal, and after a factory preset time with no signal it resumes scanning.
- Search operation (SE) mode: The scanner stops when it detects a signal. To resume scanning you must press and hold the #z key again.
Note: for Scan mode, see Menu>SCAN>Scan Mode.
Scan Sub-Code (CTCSS/DCS)
To search for a CTCSS code, do the following:
- In VFO mode, enter a known frequency, such as 144.525.
- Press [MENU] key to enter menu>>Scan>>3 Scan Sub-Code.
- Press Up or Down to select CTCSS;
- Press the [MENU] key to enter the CTCSS code, and scan the CTCSS code in sequence. When a valid CTCSS code is scanned, it stays on the CTCSS code and the speaker is turned on.
- Press the [MENU] key to store the scanned CTCSS code and exit the scan to return to the previous menu. In standby mode, the C icon will be displayed on the top line of the screen. Press and hold the PTT key to make a callback.
To search for a DCS code, do the following:
- In VFO mode, enter a known frequency, such as 144.525.
- Press [MENU] key to enter menu>>Scan>>3 Scan Sub-Code.
- Press Up or Down to select DCS;
- Press the [MENU] key to enter the DCS code scanning, and scan the DCS code in turn. When a valid DCS code is scanned, it stays on the DCS code and the speaker is turned on.
- Press the [MENU] key to store the scanned DCS code and exit the scan to return to the previous menu. In standby mode, the D icon will be displayed on the top line of the screen. Press and hold the PTT key to make a callback.
Sub-Code scan storage
In MR mode or VFO mode, the scanned CTCSS/DCS code can be stored as only TX CTCSS/DCS code, RX CTCSS/DCS code only, TX and RX CTCSS/DCS code to replace the CTCSS/DCS code setting of the current channel or frequency mode of the radio. To save the settings of CTCSS/DCS code scan, the operation is as follows:
- Press [MENU] key to enter menu >> SCAN >> 4 Scan Memory.
- Press the [MENU] key to enter the Scan Memory setting, and press the Up or Down key to select:
- ALL: The scanned CTCSS/DCS code will be stored as the received and transmitted CTCSS/DCS code of the current channel or frequency mode (at the same time as the received and transmitted Sub-Code).
- DECODER: The scanned CTCSS/DCS code will be stored as the receiver CTCSS/DCS code of the current channel or frequency mode (only replace its receiver RX CTC/DCS).
- ENCODER: The scanned CTCSS/DCS code will be stored as the transmitted CTCSS/DCS code of the current channel or frequency mode (only replace its transmitted TX CTC/DCS).
- Press the [MENU] key to save the settings and return to the previous menu;
Note: Only when a valid CTCSS/DCS code is scanned and stopped, press the [MENU] key to store the CTCSS/DCS code and replace the corresponding CTCSS/DCS code of the current channel or frequency.
8.2 DTMF (Dual-Tone Multi-Frequency)
DTMF is an in-band signaling method using dual sinusoidal signals for any given code. Originally developed for telephony systems, it has proved a very versatile tool in many other areas. In two-way radio systems, DTMF is most commonly used for automation systems and remote control. A common example would be in amateur radio repeaters where some repeaters are activated by sending out a DTMF sequence (usually a simple single-digit sequence).

DTMF frequencies and corresponding codes:
| 1209Hz | 1336Hz | 1477Hz | 1633Hz | |
|---|---|---|---|---|
| 697Hz | 1 | 2 | 3 | A |
| 770Hz | 4 | 5 | 6 | B |
| 852Hz | 7 | 8 | 9 | C |
| 941Hz | * | 0 | # | D |
The radios has a full implementation of DTMF, including the A, B, C and D codes. The numerical keys, as well as the * and #z keys correspond to the matching DTMF codes. The A, B, C and D codes are located in the Up, Down and Exit keys respectively. To send DTMF codes, press the key(s) corresponding to the message you want to send while holding down the PTT key.
In general, there are two forms of selective calling in two-way radio systems: Group call, and Private call. Group call, as the name suggest, is a one-to-many form of communication. Every radio in your working group is configured the same way and any radio will make contact with every other radio in the group. Private call, some times also known as paging, is a one-to-one form of communication. Every radio is programmed with a unique ID code. And only by sending out a matching code can you get that radio to open up to your transmissions.
Call With Signaling
A call with signaling refers to a call make to a target ID on a channel with signaling. The signaling type is DTMF signaling, which needs to be preset signaling code, and the call is realized by encoding and decoding. CPS Programming Path >> Programming >> DTMF System >> Call Code, Call Name >> ANI ID. Configure the signaling code, mute mode, and PTT-ID for the channel. With the above settings, press and hold the [PTT] key to making a call with signaling in the channel that is adapted to the DTMF signaling code. When the receiving terminal receives the matching signaling, it can decode without performing any operations. Note: Setting the PTT-ID to OFF will disable the use of the DTMF signaling function for this channel.
DTMF Manual Dial
Short press the #z key to enter DTMF manual dialing, enter the DTMF number in the following format, and press and hold the PTT key to make a DTMF call. The dialing format for DTMF calls to make Private call, Group call, and All call is as follows:
- Private call: Confirm the ID number with the #z key, and press and hold the PTT key. For example, to call 123, enter [1][2][3] # , press and hold PTT to make the call.
- Group call: Confirm the ID number with the * key, and press and hold the PTT key. For example, to call a group with prefix 12 (including 123), enter [1] [2] * , press and hold PTT to make a call. For example: enter [1]+ * to call all numbers starting with 1; Enter [1][2]+ * to call all numbers starting with 12;
- All call: Enter #z, press and hold the PTT key to make a DTMF all call.
8.3 Dual Watch
In certain situations, the ability to monitor two channels at once can be a valuable asset. This can be achieved in one of two ways. You can either have one receiver in your radio and flip-flop between two frequencies at a fixed interval (known as Dual Watch), or you can equip a radio with two receivers (known as Dual Receive or Dual VFO). The former method is cheaper to implement and far more common than the latter. The radio features Dual Watch functionality (single receiver) with the ability to lock the transmit frequency to one of the two channels it monitors.
Enabling or disabling Dual Watch mode:
- Press the [MENU] key to enter the main menu.
- Enter 3 on the numeric keypad to get to Radio Settings.
- Press the [MENU] key to confirm, enter 14 on the numeric keypad to get to 14 Dual Watch.
- Press the [MENU] key to select.
- Use the Up or Down keys to enable or disable.
- Press the [MENU] key to confirm.
- Press [EXIT] to return to the previous menu.
The dual watch function is turned on, and the icon 'D' is displayed on the top line of the screen. Repeat the above operation, select "OFF", the dual watch function is disabled, and the icon 'D' on the top line of the screen disappears. Note: When the dual watch function is turned on, the icon 'D' is displayed on the screen, and the "Singal Mode" submenu is automatically shielded in the radio setting menu. After the dual watch is turned off, the radio setting menu will automatically add "Singal Mode". After turning on the single display mode, the radio will display the channel name, frequency and channel sequence on the same screen.
8.4 Manual Programming (Channels Memory)
Memory channels are an easy way to store commonly used frequencies so that they can easily be retrieved at a later date. The radios features 999 memory channels that each can hold: Receive and transmit frequencies, transmit power, group signaling information, bandwidth, ANI/ PTT-ID settings and a six character alphanumeric identifier or channel name.
Frequency Mode vs. Channel Mode
In standby mode, press and hold the [VFO/MR] key to switch between frequency (VFO) mode and channel (MR) mode. These two modes have different functions and are often confused.
- Frequency Mode (VFO): Used for a temporary frequency assignment, such as a test frequency or quick field programming if permitted.
- Channel Mode (MR): Used for selecting preprogrammed channels.
Example 1: Programming a Channel Repeater Offset with CTCSS Tone
EXAMPLE New memory in Channel 10: RX = 432.55000 MHz, TX = 437.55000 MHz (This is a (+5) Offset), TX CTCSS tone 123.0
- Press the [MENU] key to switch between menus.
- Press and hold the [VFO/MR] key to set the radio to VFO mode, and the VFO icon is displayed on the right.
- [4] [1][7] [1] [0] - Deletes Prior Data in channel (Ex. 10)
- [4] [5] 123.0 - Selects desired TX encode tone (Ex 123 CTCSS)
- [4] [1][4] [0][5] - Enter the OFFSET frequency (Ex. 5.00MHz)
- [4] [1][5] [2] - Select the offset direction (Ex. positive offset)
- Enter RX frequency (Ex. 43255000)
- [4] [1][6] [1][0] - Enter the same channel (Ex 10), channel has been added
- Press and hold the [VFO/MR] key to return to the MR mode and the channel number will reappear.
Example 2: Programming a Simplex Channel with CTCSS tone
EXAMPLE New memory in Channel 10: RX = 432.6500 MHz, TX CTCSS tone 123.0
- Press the [MENU] key to switch between menus.
- Press and hold the [VFO/MR] key to set the radio to VFO mode, and the VFO icon is displayed on the right.
- [4] [1][7] [1] [0] - Deletes Prior Data in channel (Ex. 10)
- [4] [5] 123.0 - Selects desired TX encode tone (Ex 123 CTCSS)
- Enter RX frequency (Ex. 43265000)
- [4] [1][6] [1][0] - Enter the same channel (Ex 10), channel has been added
Repeaters Programming
The following instructions assume that you know what transmit and receive frequencies your repeater employs, and that you're authorized to use it.
- Press and hold the [VFO/MR] key, the transceiver is set to VFO mode, and the VFO icon will be displayed on the right.
- Use the numeric keypad to enter the repeater's output (your receive) frequency.
- Press [4] [1] [4] to get the offset frequency.
- Use the numeric keypad to enter the specified frequency offset.
- Press [MENU] to confirm and save.
- Press [4] [1] [5] to get the offset direction.
- Use the Up or Down keys to select plus (positive) or minus (negative) offset.
- Press [MENU] to confirm and save.
- Optional:
a) Save to memory, see the section called "Manual programming" for details.
b) Set up CTCSS; see the section called "CTCSS" for details. - Press [EXIT] to exit the menu. If everything went well, you should be able to make a test call through the repeater.
NOTE: If you're experiencing problems making a connection to the repeater, check your settings and/or go through the procedure again. Certain Amateur Radio repeaters (especially in Europe) use a 1750Hz tone burst to open up the repeater. To see how this is done with the radios, see the section called "1750Hz Tone-burst". If you're still unable to make a connection, contact the person in charge of the radio system with your employer or your local amateur radio club, as the case may be.
Amateur Radio Setup
In contrast with Commercial radio operators, who often need very specific requirements to be compatible with a very specific radio implementation, Amateur radio operators tend to need the broadest possible settings in order to be compatible with as many systems as possible. This basically implies turning all the fancy features that you typically might need for a commercial setup off. In a typical Amateur radio setup the following settings would be recommended:
Radio setting:
- Turn ANI, DTMFST, PTT-ID off and PTT-LT to 0ms (menu items 18 through 19 and 19 through 20).
- Turn off Squelch Tail Elimination (Tail) features (menu items 23).
- Turn roger beep (ROGER) off (menu item 10).
Program channel:
- Set bandwidth to Wide (menu item 5).
- Turn DCS and CTCSS off (menu items 6 through 9).
- Turn Signaling code off and SPK-Mute (menu items 11 and 13).
10. Troubleshooting Guide
If you encounter any issues with your Baofeng UV18 Pro Max, please refer to the table below for common problems and their solutions. If the problem persists, contact your dealer for technical support.
| Phenomena | Analysis | Solution |
|---|---|---|
| You cannot turn on the radio. | The battery may be installed improperly. The battery power may run out. The battery may suffer from poor contact caused by dirty or damaged battery contacts. | Remove and reattach the battery. Recharge or replace the battery. Clean the battery contacts or replace the battery. |
| During receiving, the voice is weak or intermittent. | The battery voltage maybe low. The volume level may be low. The antenna maybe loose or maybe installed incorrectly. The speaker maybe blocked. | Recharge or replace the battery. Increase the volume. Turn off the radio, and then remove and reattach the antenna. Clean the surface of the speaker. |
| You cannot communicate with other group members. | The frequency or signaling type maybe inconsistent with that of other members. You may be too far away from other members. | Verify that your TX/RX frequency and signaling type are correct. Move towards other members. |
| You hear unknown voices or noise. | You may be interrupted by radios using the same frequency. The radio in analog mode maybe set to no signaling. | Change the frequency, or adjust the squelch level. Request your dealer to set signaling for the current channel to avoid interference. |
| You are unable to hear anyone because of too much noise and hiss. | You may be too far away from other members. You may be in an unfavorable position. For example, your communication may be blocked by high buildings or blocked in an underground area. It may be the result of external disturbance (such as electromagnetic interference). | Move towards other members. Move to an open and flat area, restart the radio, and try again. Stay away from equipment that may cause interference. |
| The radio keeps transmitting. | VOX may be turned on or the headset is not installed in place. | Turn off the VOX function. Check that the headphones are in place. |
NOTE: If the above solutions cannot fix your problems, or you may have some other queries, please contact your dealer for more technical support.
11. Technical Specifications
| GENERAL | |
|---|---|
| Channel Capacity | 1000 |
| Channel Spacing | 25.0 KHz/12.5 KHz |
| Input Voltage | 7.4 VDC |
| Battery Life: 5% TX, 5% RX, 90% Standby | Li-on: 15 hours @ 5 watts |
| Current Drain: Standby | 45 mA |
| Receive | 200 mA |
| Transmit | ≤1.6 A @ High Power, ≤1.2 A @ Low Power |
| Operating temperature | -10°C to 60°C |
| Antenna Impedance | 50Ω |
| Radio Dimensions | 127mm x 69mm x 38mm (not including antenna) |
| TRANSMITTER | |
| Frequency Range (TX) | 136 to 174 MHz, 220 to 260 MHz, 400 to 480 MHz |
| RF Output Power | 2 or 5 Watts Max |
| Modulation | 16K0F3E/11K0F3E |
| Spurious Emission | -16 dBm<1GHz, -16 dBm>1GHz |
| Frequency Stability | ±2.5 ppm |
| Audio Distortion | ≤5% |
| FM Hum & Noise | 40 dB |
| RECEIVER | |
| Frequency Range | 136 to 174 MHz, 220 to 260 MHz, 400 to 520 MHz, FM78 to 108MHz, AM 108 to 136MHz, 350 to 390 MHz, |
| Sensitivity: 12 dB SINAD | -120 dBm |
| Adjacent Channel Selectivity | -60 dBm |
| Intermodulation and Rejection | -70 dBm |
| Rated Audio Power Output | 1.0 Watts @ 16 Ω |
| Rated Audio Distortion | ≤5% |
NOTE: All specifications may be modified without prior notice or liability. Thank you.

12. User Tips
No specific user tips were available from the provided reviews or Q&A. For common issues, please refer to the Troubleshooting Guide section.
13. Warranty and Support
Disclaimer
The accuracy and completeness of the contents are sought in the process of compilation, but we do not bear any responsibility for the possible errors or omissions. With the continuous development of technology, we reserve the right to change the design and specification of the product without notice. No copy, modification, translation and dissemination of this handbook may be made in any form without the prior written authorization of our department.
Contact Information
Fujian Baofeng Electronics Co., Ltd.
ADD: Changfu Industrial Bank Xiamei, Nan'an, Quanzhou, Fujian, China
E-mail: wangjianhui@baofengradio.com
Website: http://www.baofengradio.com
Print version: UV-18R(HD) V2.0