BAOFENG UV-K5 Pro Max

Contents

Baofeng UV-K5 Pro Max Walkie Talkie User Manual

12W High Capacity AM FM Two Way Radio

1. Introduction and Safety Warnings

Thank you for purchasing the Baofeng UV-K5 Pro Max Walkie Talkie. This dual-band, dual-display, dual-watch radio is designed to provide secure, instant, and reliable communications. Please read this manual carefully to ensure maximum performance and safe operation.

1.1 Regulations and Safety Warnings

EU Regulatory Conformance

This product complies with the essential requirements and other relevant provisions of Directive 2014/53/EU. All applicable EU regulations are regarded (2006/66/EC, 2011/65/EU, 2012/19/EU). This information is applicable to EU countries only.

FCC Part 15 / IC Compliance

This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

FCC RF Exposure Warning

It is the user's responsibility to properly operate this radio transmitter to ensure safe operation. Adhere to the following guidelines:

  • Do not use the radio with a damaged antenna. Contact your local dealer for a replacement antenna if needed.
  • For hand-held operation, hold the radio 1 inch (2.5 cm) from the user's face to comply with FCC RF exposure requirements.
  • For body-worn operation, use the supplied belt-clip accessory. Third-party accessories (unless approved by the manufacturer) should be avoided as they might not comply with FCC RF exposure guidelines.

Operating Prohibitions

To prevent property loss, bodily injury, or death, observe the following:

  • Do not operate the product in locations with fuels, chemicals, explosive atmospheres, or other flammable/explosive materials.
  • Do not operate the product near or in any blasting area.
  • Do not operate the product near medical or electronic equipment vulnerable to RF signals.
  • Do not hold the product while driving.
  • Do not operate the product in any area where wireless communication equipment is prohibited.
  • Do not disassemble, modify, or repair the product and its accessories without authorization.

Precautions for Batteries

To prevent property loss, bodily injury, or death, observe the following:

  • Do not charge or replace your battery in a location containing fuels, chemicals, explosive atmospheres, or other flammable/explosive materials.
  • Do not charge a wet battery. Dry it with a soft, clean cloth before charging.
  • Do not charge a battery suffering deformation, leakage, or overheat.
  • Do not charge your battery with an unauthorized charger.
  • Do not charge your battery in a location where strong radiation is present.
  • Overcharging is prohibited as it may shorten battery life.
  • Do not dispose of the battery in fire.
  • Do not expose the battery to direct sunlight or other heating sources.
  • Do not squeeze or penetrate the battery, nor remove its housing.

Important Tips

  • Do not use any unauthorized or damaged accessory.
  • Keep the product at least 2.5 centimeters away from your body during transmission.
  • Do not keep the product receiving at high volume for a long time.
  • For vehicles with an airbag, do not place the product in the area over the airbag or in the airbag deployment area.
  • Keep the product and its accessories out of reach of children and pets.
  • Operate the product within the specified temperature range.
  • Continuous transmission for a long time may lead to heat accumulation. Allow for cooling.
  • Handle the product with care.

2. Package Contents

The standard package for your Baofeng UV-K5 Pro Max includes the following items:

  • 1 x Radio
  • 1 x Battery
  • 1 x Belt Clip
  • 1 x Hand Strap
  • 1 x Desktop Charger
  • 1 x Type-C Charger Cable
  • 1 x Product Manual
  • 1 x Antenna
Standard package contents of the Baofeng UV-K5 Pro Max Walkie Talkie, including the radio, battery, belt clip, hand strap, desktop charger, Type-C cable, and manual.
Figure 2.1: Standard Package Contents

3. Product Overview

The Baofeng UV-K5 Pro Max features a 1.77-inch TFT large screen, full keyboard, and supports a wide range of frequencies and functions.

Front view of the Baofeng UV-K5 Pro Max Walkie Talkie, highlighting its 1.77 inch LED display, high capacity battery, 999 channels, NOAA weather alert, Type-C charging, and six-band frequency ranges.
Figure 3.1: Baofeng UV-K5 Pro Max Front View with Key Features

3.1 Main Controls and Parts

  1. Power/Volume knob: Controls power and volume.
  2. SK1- Broadcast FM and Alarm key: Momentary press for FM radio, long press for alarm.
  3. PTT key: Push-to-Talk button for transmission.
  4. V/M mode key: Switches between Frequency (VFO) and Memory (MR) modes.
  5. Status LED: Indicates radio status (transmitting/receiving).
  6. SK2-Flashlight and Monitor key: Momentary press for flashlight, long press for monitor function.
  7. A / B select key: Switches between upper (A) and lower (B) displays.
  8. MENU Key: Activates menu, confirms selections.
  9. Numeric keypad: For inputting frequencies, channel numbers, and DTMF codes.
  10. Antenna jack: Connection point for the antenna.
  11. LED flashlight: Built-in light.
  12. Color LCD: 1.77-inch display.
  13. Accessory jack: For external speaker/microphone.
  14. Speaker and microphone: For audio input and output.
  15. BAND key: Switches between VHF/UHF bands, long press for one-touch search.
  16. EXIT Key: Exits menus and functions, long press for one-touch search function.
  17. ▲ or ▼ navigation keys: For navigating menus and adjusting frequencies/channels.
  18. Type-C charging port: For direct charging.
  19. Type-C charging indicator: Indicates charging status.
  20. Battery release latch: Releases the battery pack.
Side view of the Baofeng UV-K5 Pro Max, showing the Switch Key, PTT Key, and Type-C charging port.
Figure 3.2: Side Controls and Type-C Port

3.2 LCD Display Icons

IconDescription
RSSISquelch Open/Close Indicator
H/LTransmit power level indicator (High/Low)
♪DTMF side tone from radio speaker (DT-ST, ANI-ST, DT+ANI)
DDCS enabled
CCTCSS enabled
+Repeater access in VFO/Frequency Mode (TX shifted higher)
-Repeater access in VFO/Frequency Mode (TX shifted lower)
DDual watch enabled
🔒Keypad lock enabled
🗣️VOX enabled
📞Confidential calling feature activated
NNarrowband enabled
🔋Battery level indicator
RReverse function enabled
▶Indicates active band or channel
SCRVoice scramble function activated

Battery Level Indicator

When the battery level indicator shows a low battery, the radio will beep periodically, flash the display backlight, and announce "Low Voltage" if voice prompts are enabled. This indicates the need to charge or replace the battery.

4. Setup and Installation

4.1 Charging the Battery

The Li-ion battery pack is not charged at the factory. Please charge it before first use. For optimal performance, fully charge and discharge the battery two or three times. The battery pack life may decrease over time, even with proper charging; if this occurs, replace the battery pack.

Charger Supplied

Use only the specified charger provided. Using other chargers may cause explosion or personal injury. If the radio displays low battery, charge it immediately.

How to Charge

  1. Plug the AC adaptor into an outlet, then plug the cable into the DC jack on the back of the charger. The indicator light will blink orange, ready to charge.
  2. Plug the battery or the radio into the charger, ensuring good contact with charging terminals. The indicator light will turn red, indicating charging has begun.
  3. Charging takes approximately 2-5 hours. When the lamp lights green, charging is complete. Remove the battery or radio unit.

Note: If the radio is powered on during charging, the indicator may not turn green to show full charge, as the radio consumes energy. Turn off the radio for accurate charging indication.

Using the Type-C USB Charger

The Type-C USB port allows convenient charging of your Li-ion battery pack.

  1. Ensure your radio is turned OFF.
  2. Plug the Type-C USB cable into the charging port on your battery. Connect the other end to a wall power outlet.
  3. An empty battery will be fully charged in approximately 4 hours.
  4. The battery meter on the LCD will move to indicate charging.

Note: It is recommended to power OFF your radio while charging. If powered ON, you may not be able to transmit if the battery is completely empty. Allow time for the battery to charge to 1 bar before transmitting. For optimal battery life, remove the radio from the charger within 6 hours and do not store it connected to the charger.

Illustration of the Baofeng UV-K5 Pro Max Walkie Talkie being charged via its Type-C port, with a glowing battery icon indicating charging.
Figure 4.1: Type-C Charging

4.2 Installing/Removing the Antenna

  1. Installing: Screw the antenna into the connector on top of the transceiver by holding the antenna at its base and turning it clockwise until secure.
  2. Removing: Turn the antenna counter-clockwise to remove it.

4.3 Installing the Belt Clip

  1. At the back of the radio, locate the two parallel screws above the battery. Remove these and thread them through the holes on the belt clip. Screw them back into the radio body.
  2. Removing: Unscrew counter-clockwise to remove the belt clip.

4.4 Installing/Removing the Battery Pack

Before attaching or removing the battery, ensure your radio is turned off by turning the power/volume knob all the way counter-clockwise.

  1. Ensure the battery is aligned parallel with the radio body, with its lower edge about 1-2cm below the radio's edge.
  2. Slide the battery upward along the guide-rails until it clicks into place.

To remove the battery, press the battery release above the battery pack and slide the battery downward.

4.5 Installing Additional Speaker/Microphone (Optional)

Pry open the rubber MIC-Headset jack cover and insert the Speaker/Microphone plug into the double jack.

Diagram showing the connection points for an optional speaker/microphone accessory to the Baofeng UV-K5 Pro Max, indicating the 2.5mm and 3.5mm jacks.
Figure 4.2: Speaker/Microphone Connection Diagram

5. Basic Operations

5.1 Power On/Off

  • Turning the unit on: Rotate the Volume/Power knob clockwise until you hear a "click". The radio will power on with an audible double beep and display a frequency or channel.
  • Turning the unit off: Rotate the Volume/Power knob counter-clockwise all the way until you hear a "click".

5.2 Adjusting the Volume

Rotate the Volume/Power knob clockwise to increase volume and counter-clockwise to decrease volume. Be careful not to turn it too far, as you may inadvertently turn the radio off. Use the monitor function (long press SK2) to adjust volume with un-squelched static.

5.3 Main Band/Sub Band Select

In standby mode, press the [A/B] key to switch between the A (upper) and B (lower) displays. The selected display's frequency or channel becomes the active listening and transmit frequency/channel. To save frequencies to channel memory, you must be on the A display.

5.4 VFO/Channel Switch

Press the [V/M] key to switch between VFO (Frequency) and Channel (MR) display modes.

  • In Channel (MR) mode, the channel number is displayed.
  • In Frequency (VFO) mode, 'VFO' is displayed.

5.5 Frequency (VFO) Mode

In VFO mode, use the ▲ or ▼ keys to navigate up and down the band. Each press increments or decrements the frequency by the set step. You can also input frequencies directly using the numeric keypad.

Example: Entering 436.61250 MHz on display A

  1. In standby mode, press [V/M] key to switch to VFO mode.
  2. Enter [4][3][6][6][1][2][5][0] on the numeric keypad.

5.6 Channel (MR) Mode and Channel Selection

Channel (MR) mode is practical for everyday use, while VFO mode is useful for experimentation and programming. In MR mode, you can navigate channels using the ▲ or ▼ keys or the encoder.

To switch to Channel mode, press the [V/M] key.

  • Operation 1: Press the ▲ or ▼ navigation key to select the channel.
  • Operation 2: Input the channel numbers directly using the keyboard (e.g., [0][1][2] for channel 12).

5.7 Making a Call

To ensure the best reception volume, keep the distance between the microphone and your mouth at 2.5 cm to 5 cm during transmission.

  • Channel mode call: Select a channel, then hold down the [PTT] key to transmit. Speak into the microphone. The red LED will be on.
  • Frequency mode call: Switch to VFO mode, input the desired frequency, then hold down the [PTT] key to transmit. The red LED will be on.
  • Receive a call: Release the [PTT] key to answer. The green LED will be on when receiving a call.

5.8 Using the Flashlight

The radio has a high-intensity LED flashlight.

  1. Press [SK2] key once to turn on the flashlight (Always On mode).
  2. Press [SK2] key again for Strobe Light (emergency signal).
  3. Press [SK2] key a third time to turn off the flashlight.

5.9 Emergency Alert

The Emergency Alert feature signals group members for help.

  • To activate, press and hold the [SK1] key for 3 seconds. The radio will emit a loud siren and the flashlight will flash.
  • Press the [SK1] key to exit the emergency alert function.

WARNING: The Emergency Alert feature should only be used in an actual emergency.

5.10 FM Radio (FM)

The radio can receive FM broadcasts in the 65-108MHz range. The [BAND] key switches between 65-75 MHz and 76-108 MHz bands.

  1. In frequency or channel mode, press [SK1] key to turn on the radio.
  2. Select the desired radio frequency with the ▲ or ▼ keys or input the frequency. Press #z to automatically search for a radio station.
  3. Press [SK1] key to exit FM radio.

Note: While listening to FM, if a signal is received on the active frequency/channel, the radio will automatically switch to that frequency/channel for normal transmitting/receiving. It will switch back to FM radio mode when the signal disappears.

5.11 Monitor

In standby, press and hold the [SK2] key to enter Monitor mode. This allows you to hear weak signals or when the matched carrier is present but signaling is too weak. Release [SK2] to turn off speakers and return to standby. If no signal, pressing [SK2] will emit noise.

5.12 Keypad Lock

The keypad lock disables all keys except the three side keys.

  • To enable/disable, press and hold the * key for about two seconds.
  • You can also configure the radio to automatically lock the keypad after ten seconds from the menu.

5.13 Frequency Reversal

A short momentary press of the * key enables the reverse function. This allows you to listen to the repeater's input frequency. The LCD will display "R" in the top row, next to the + and - for the offset direction.

5.14 TX Repeaters Tone

Press [PTT] + [SK2] key to send a 1750Hz repeater tone. This is useful for communications through repeaters. This function works even if the keypad lock is enabled.

This function allows the radio to search for active frequencies.

  1. Press and hold the [BAND] key. The screen will display "SEARCH SEARCH...".
  2. If a stable signal is received, the frequency will be displayed. CTCSS or DCS values will also be shown if present.
  3. Press the [MENU] key to save the searched frequency and CTCSS/DCS to a channel.

Note: During frequency search, press the #z key to switch between UHF or VHF bands.

5.16 Weather Radio/Scan Weather Channel

Your radio has NOAA Weather Radio and NOAA Weather Scan functions to receive weather reports from designated NOAA stations.

  1. To turn on NOAA Weather Scan, press the [0sQL] key for 3 seconds. A cloud icon will appear, and the radio will enter Weather band mode.
  2. Press and hold the #z key for 3 seconds to start automatic scanning of all 10 NOAA channels. Press again to stop the scan.
  3. After stopping the scan, you can manually select the weather channel using the ▲ or ▼ key.
  4. To exit Weather Radio broadcast mode, press the [EXIT] key or [PTT] key.

Weather Channel Frequencies

Channel NumberRX Frequency MHzChannel NumberRX Frequency MHz
Wx-01162.550Wx-06162.500
Wx-02162.400Wx-07162.525
Wx-03162.475Wx-08161.650
Wx-04162.425Wx-09161.775
Wx-05162.450Wx-10163.275

Note: Weather Channels Wx 1 Thru 10 are Receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.

6. Advanced Features

6.1 Working the Menu System

For a complete reference of menu items and parameters, refer to Appendix B, Menu definitions (page 35-40 of the PDF). If your radio is in Memory (MR) mode, certain menu items (STEP, TXP, W/N, CTCSS, DCS, S-CODE, PTT-ID, BCL, SFT-D, OFFSET, MEM-CH) will not take effect.

Basic Menu Use with Arrow Keys

  1. Press the [MENU] key to enter the menu.
  2. Use the ▲/▼ keys to navigate between menu items.
  3. Press [MENU] again to select the desired menu item.
  4. Use the ▲/▼ keys to select the desired parameter.
  5. To confirm your selection, press [MENU] to save and return to the main menu. To cancel changes, press [EXIT] to reset and exit.
  6. To exit the menu at any time, press the [EXIT] key.

Using Menu Shortcuts

Each menu item has a numerical value for direct access.

  1. Press the [MENU] key to enter the menu.
  2. Use the numerical keypad to enter the number of the menu item.
  3. Press the [MENU] key to enter the menu item.
  4. For parameters, use arrow keys or numerical keypad for short-cut code.
  5. Confirm with [MENU] to save or [EXIT] to cancel.
  6. Exit with [EXIT] key.

6.2 Scanning

The radio features a built-in scanner for VHF and UHF bands. In Frequency (VFO) mode, it scans in steps according to your set frequency step. In Channel (MR) mode, it scans your programmed channels. Dual Watch is inhibited while scanning.

  • To enable the scanner, press and hold the #z key for about two seconds.
  • To exit scanning mode, press and hold the #z key again.

Scanning Modes

The scanner has three operation modes: Time, Carrier, or Search.

  • Time Operation (TO): Scanner stops on a signal, then resumes after a preset timeout.
  • Carrier Operation (CO): Scanner stops on a signal, then resumes after a preset time with no signal.
  • Search Operation (SE): Scanner stops on a signal. To resume, press and hold the #z key again.

Frequency Scanning

This function scans frequencies.

  1. In frequency mode, press #z key for more than 2 seconds. The radio will start scanning according to the set frequency step.
  2. You can change the scanning direction with the ▲/▼ keys.
  3. Press #z key to stop the scanning.

Channel Scanning

This function scans channels.

  1. In channels mode, press #z key for more than 2 seconds. The radio will start scanning according to your set channels.
  2. You can change the scanning direction with the ▲/▼ keys.
  3. Press #z key to stop scanning.
Diagram illustrating three types of scanning: Subtone scanning and storage, and Channel Scanning, with a radio displaying a radar-like interface.
Figure 6.1: Scanning Types

Scan CTCSS/DCS

This function scans frequencies with CTCSS or DCS tones enabled. It cannot be activated in Channel mode and will only start when the receiving band detects a signal.

  • Scan CTCSS: In standby, press [MENU] [1][4], then [MENU] to start scanning.
  • Scan DCS: In standby, press [MENU] [1][5], then [MENU] to start scanning.

6.3 Manual Programming (Channels Memory)

The radio features 999 memory channels. Each channel can store receive/transmit frequencies, power, signaling information, bandwidth, ANI/PTT-ID settings, and a six-character alphanumeric identifier.

Frequency Mode vs. Channel Mode

Press [V/M] key to switch between VFO (Frequency) and MR (Channel) modes.

  • Frequency Mode (VFO): For temporary frequency assignments or quick field programming.
  • Channel Mode (MR): For selecting preprogrammed channels.

Programming a Channel Repeater Offset with CTCSS Tone (Example)

New memory in Channel 10: RX = 432.55000 MHz, TX = 437.55000 MHz ((+ 5) Offset), TX CTCSS tone 123.0

  1. Press [EXIT] to switch between menus.
  2. Press [V/M] to set the radio to VFO mode.
  3. [MENU] [3][1] [MENU] [1][0] [MENU] [EXIT] (Deletes Prior Data in channel 10)
  4. [MENU] [1][2] [MENU] 123.0 [MENU] [EXIT] (Selects desired TX encode tone)
  5. Enter RX frequency (e.g., 43255000).
  6. [MENU] [3][0] [MENU] [1][0] [MENU] --> [EXIT] (Enter desired channel 10, RX added)
  7. Enter TX frequency (e.g., 43755000).
  8. [MENU] [3][0] [MENU] [1][0] [MENU] --> [EXIT] (Enter same channel 10, TX added)
  9. Press [V/M] to return to MR mode.

Programming a Simplex Channel with CTCSS Tone (Example)

New memory in Channel 10: RX = 432.6625 MHz, TX CTCSS tone 123.0

  1. Press [EXIT] to switch between menus.
  2. Press [V/M] to set the radio to VFO mode.
  3. [MENU] [3][1] [MENU] [1][0] [MENU] [EXIT] (Deletes Prior Data in channel 10)
  4. [MENU] [1][2] [MENU] 123.0 [MENU] [EXIT] (Select desired TX encode tone 123 CTCSS)
  5. Use [EXIT] to select Upper display.
  6. Enter RX frequency (e.g., 43266250).
  7. [MENU] [3][0] [MENU] [1][0] [MENU] --> [EXIT] (Enter desired channel 10, RX added)
  8. Enter TX frequency (e.g., 43266250).
  9. [MENU] [3][0] [MENU] [1][0] [MENU] --> [EXIT] (Enter same channel 10, TX added)
  10. Press [V/M] to return to MR mode.

6.4 Repeaters Programming

This assumes you know your repeater's transmit and receive frequencies and are authorized to use it.

  1. Press [V/M] to set the radio to VFO mode.
  2. Use the numeric keypad to enter the repeater's output (your receiving) frequency.
  3. Press [MENU] to enter the menu.
  4. Enter [2][9] on the numeric keypad for frequency offset.
  5. Press [MENU] to select.
  6. Use the numerical keypad to enter the specified frequency offset (see "29 OFFSET - Frequency shift amount" in Appendix B).
  7. Press [MENU] to confirm and save.
  8. Enter [2][8] on the numeric keypad for offset direction.
  9. Use the ▲/▼ keys to select + (positive) or - (negative) offset.
  10. Press [MENU] to confirm and save.
  11. (Optional) Save to memory (see Manual Programming) or set up CTCSS (see CTCSS details).
  12. Press [EXIT] to exit the menu.

Note: If you experience problems, check your settings or repeat the procedure. Some repeaters (especially in Europe) use a 1750Hz tone burst. If unable to connect, contact the radio system administrator.

6.5 VOX (Voice Operated Transmit)

VOX allows hands-free conversations. Speak towards the microphone, and communication activates automatically.

  • In standby mode, press [MENU] + 7. The screen displays "VOX".
  • Press [MENU] to enter the function. Use ▲/▼ keys to turn off VOX or select VOX level (1-10).
  • Press [MENU] to confirm.
  • Press [EXIT] to return to standby mode.

Note: Level 1 is the least sensitive, level 9 is the most sensitive. VOX is not enabled in Scan or FM Radio mode.

6.6 Dual Watch

Dual Watch allows monitoring two channels simultaneously. The radio features single-receiver Dual Watch functionality, with the ability to lock the transmit frequency to one of the monitored channels.

Enabling or Disabling Dual Watch Mode

  1. Press the [MENU] key to enter the menu.
  2. Enter 7 on the numeric keypad to get to Dual Watch.
  3. Press [MENU] key to select.
  4. Use the UP and DOWN keys to enable or disable.

6.7 Stopwatch Timer

  • In standby mode, press [MENU] + 44. The screen displays "STOP WATCH".
  • Press [MENU] to enter the function. Use ▲/▼ keys to enable (ON) the function, then press [MENU] for confirmation.
  • To return to standby mode, press [EXIT] key.
  • When ON, press [MENU] to start counting. Press [MENU] again to re-start counting.
  • To exit, stop counting first, then press [EXIT].

6.8 Scrambler

The scrambler protects communications by voice inversion, preventing unauthorized listening. The "SCR" icon appears on the display when enabled.

  • In standby mode, press [MENU] + 45. The screen displays "SCRAMBLE".
  • Press [MENU] to enter the function. Use ▲/▼ keys to select scramble mode (MODE1 to MODE3) to activate.

6.9 DTMF (Dual-Tone Multi-Frequency)

DTMF is an in-band signaling method using dual sinusoidal signals. It's commonly used in two-way radio systems for automation and remote control, such as activating amateur radio repeaters.

DTMF Frequencies and Corresponding Codes

1209Hz1336Hz1477Hz1633Hz
697Hz123A
770Hz456B
852Hz789C
941Hz*0#D

To send DTMF codes, press the key(s) corresponding to the message while holding down the PTT key. This works even with keypad lock enabled.

6.10 Customization

The radio allows customization of visual and audible features.

  • Display Backlight (ABR) - MENU 7: In standby, press [MENU] + 7, then [MENU]. Use ▲/▼ keys to select delay time (ON/5sec/10sec/15sec/20sec). Press [MENU] to confirm, [EXIT] to return.
  • Beep Prompt (BEEP) - MENU 8: Enables/disables a beep tone when a key is pressed. In standby, press [MENU] + 8, then [MENU]. Use ▲/▼ keys to turn ON/OFF. Press [MENU] to confirm, [EXIT] to return.
  • Voice Function (VOICE) - MENU 17: Enables/disables audible voice confirmation. In standby, press [MENU] + 17, then [MENU]. Use ▲/▼ keys to select OFF/ON. Press [MENU] to confirm, [EXIT] to return.
  • Language of the Menu (LANGUAGE) - MENU 18: Sets the menu language (English). In standby, press [MENU] + 18.
  • Working Mode (MDF-A) - MENU 24: Selects display mode: Frequency (FREQ), Channel (CH), or Channel Name (NAME). In standby, press [MENU] + 24. Use ▲/▼ keys to select, then [MENU] to confirm.
  • Roger Beep (ROGER) - MENU 36: Enables/disables an end-of-transmission tone. In standby, press [MENU] + 36, then [MENU]. Use ▲/▼ keys to select OFF/ON. Press [MENU] to confirm, [EXIT] to return.
  • Power On Message (POWER ON MSG) - MENU 40: Customizes the welcome message displayed on startup. Options include VOLTAGE, MESSAGE, LOGO, or MODEL NAME. In standby, press [MENU] + 40, then [MENU]. Use ▲/▼ keys to select, then [MENU] to confirm, [EXIT] to return.
  • Power On Password (POWER ON PWD) - MENU 43: Enables/disables a password prompt on startup. In standby, press [MENU] + 43, then [MENU]. Use ▲/▼ keys to select ON/OFF. Press [MENU] to confirm, [EXIT] to return.

6.11 Reset - MENU 42

The transceiver has two reset modes: VFO and ALL.

  • Reset VFO: Resets all settings except channels to default. In standby, press [MENU] + 42, then [MENU]. Use ▲/▼ keys to select VFO, then [MENU] to confirm. Confirm "Sure to reset?" with [MENU].
  • Reset ALL: Resets all settings to default. In standby, press [MENU] + 42, then [MENU]. Use ▲/▼ keys to select ALL, then [MENU] to confirm. Confirm "Sure to reset?" with [MENU].

7. User Tips

Based on common user feedback, here are some tips for using your Baofeng UV-K5 Pro Max:

  • Battery Life: To maximize battery life, avoid overcharging and ensure the radio is turned off during charging for a full cycle.
  • Programming: When programming, it's often easier to use the programming cable and PC software for complex channel setups.
  • Signal Clarity: If experiencing poor signal, try adjusting the squelch level (SQL setting in MENU) or moving to an open area.
  • Keypad Lock: Utilize the keypad lock feature to prevent accidental button presses, especially when carrying the radio.
  • NOAA Weather: Remember that NOAA weather channels are receive-only; you cannot transmit on them.

8. Troubleshooting

If you encounter issues with your radio, refer to the table below for common problems and solutions. If these solutions do not resolve your problem, please contact your dealer for technical support.

PhenomenaAnalysisSolution
You cannot turn on the radio.The battery may be installed improperly.
The battery power may run out.
The battery may suffer from poor contact caused by dirty or damaged battery contacts.
Remove and reattach the battery.
Recharge or replace the battery.
Clean the battery contacts or replace the battery.
During receiving, the voice is weak or intermittent.The battery voltage may be low.
The volume level may be low.
The antenna may be loose or incorrectly installed.
The speaker may be blocked.
Recharge or replace the battery.
Increase the volume.
Turn off the radio, then remove and reattach the antenna.
Clean the surface of the speaker.
You cannot communicate with other group members.The frequency or signaling type may be inconsistent with that of other members.
You may be too far away from other members.
Verify your TX/RX frequency and signaling type are correct.
Move towards other members.
You hear unknown voices or noise.You may be interrupted by radios using the same frequency.
The radio in analog mode may be set with no signaling.
You may be too far away from other members.
Change the frequency, or adjust the squelch level.
Request your dealer to set signaling for the current channel to avoid interference.
Move towards other members.
You are unable to hear anyone because of too much noise and hiss.You may be in an unfavorable position (e.g., blocked by high buildings or underground).
It may be the result of external disturbance (e.g., electromagnetic interference).
Move to an open and flat area, restart the radio, and try again.
Stay away from equipment that may cause interference.
The radio keeps transmitting.VOX may be turned on or the headset is not installed in place.Turn off the VOX function. Check that the headphones are in place.

9. Technical Specifications

CategorySpecification
Frequency RangeFM65-108MHz(Rx); AM108-136MHz(Rx)
VHF1: 136-174MHz(Rx&Tx); VHF2: 200-260MHz(Rx&Tx)
UHF1: 350-390 MHz(Rx); UHF2: 400-480MHz(Rx&Tx)
Channel Spacing25.0KHz(Wide)/12.5KHz(Narr)
Memory Channel999 Groups
Operation VoltageDC 7.4 V ±10%
Transmission current≤2800mA
Receive Sensitivity0.25μV (12dB SINAD)
Rated Audio Power Output1W @16 ohms
Receive current≤380mA
Connection for accessories2 pin Kenwood jack
Antenna impedance50 Ohm
Dimensions115*60*33mm
MaterialPlastic
Waterproof / Water-ResistantIP45
Output Power(w)5w-10w
Battery Capacity(mAh)High Capacity

NOTE: All specifications may be modified without prior notice or liability.

10. Warranty and Support

10.1 Maintenance

Your Two Way Radio is an electronic product of exact design and should be treated with care. The suggestions below will help you to fulfill any warranty obligations and to enjoy this product for many years.

  • Do not attempt to open the radio for any reason! The radio's precision mechanics and electronics require experience and specialized equipment. Unauthorized opening of the transceiver will void the warranty.
  • Do not store the radio under direct sunlight or in hot areas.
  • High temperatures can shorten the life of electronic devices and warp or melt plastics.
  • Do not store the radio in dusty and dirty areas.
  • Keep the radio dry. Rainwater or dampness will corrode electronic circuits.
  • If the radio emits a peculiar smell or smoke, immediately shut off power and remove the charger or battery.
  • Do not transmit without an antenna.

10.2 Disclaimer

The Company endeavors to achieve the accuracy and completeness of this manual, but no warranty of accuracy or reliability is given. All specifications and designs are subject to change without notice due to continuous technological development. No part of this manual may be copied, modified, translated, or distributed in any manner without the prior written consent of the Company. We do not guarantee, for any particular purpose, the accuracy, validity, timeliness, legitimacy, or completeness of the third-party products and contents involved in this manual.

10.3 Further Support

If the provided troubleshooting steps do not resolve your issues, or for any other queries, please contact your dealer for more technical support.

For a detailed user manual, you may refer to the official PDF document: Baofeng UV-K5 Pro Max User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.