BD7077 BD7077

Contents

User Manual: 77 LED Solar Motion Sensor Floodlight

Model: BD7077

Introduction

Thank you for choosing the 77 LED Solar Motion Sensor Floodlight. This device is designed to provide efficient and reliable outdoor illumination, featuring a motion sensor for enhanced security and a dummy camera design for added deterrence. Powered by solar energy, it is an eco-friendly and cost-effective lighting solution for your porch, garden, patio, or other outdoor areas.

This manual provides essential information for the proper installation, operation, and maintenance of your solar floodlight. Please read it thoroughly before use and retain it for future reference.

Key Features

  • Solar Powered: Utilizes a high-efficiency solar panel for charging, eliminating the need for external power sources.
  • Motion Sensor: Automatically activates high-brightness lighting upon detecting movement.
  • 77 LED SMD2835 Beads: Provides bright and wide-angle illumination.
  • Waterproof IP65: Designed to withstand various weather conditions, including rain.
  • Dummy Security Camera Design: Acts as a visual deterrent against intruders.
  • Adjustable Bracket: Allows for flexible positioning and light direction.
  • Multiple Lighting Modes: Offers three distinct operating modes to suit different needs.
  • Remote Control: Conveniently switch modes and power on/off.

Package Contents

Please check the package to ensure all items are present and in good condition:

  • 77 LED Solar Motion Sensor Floodlight
  • Mounting Bracket
  • Remote Control
  • Mounting Screws and Wall Plugs
  • User Manual (this document)

Specifications

Product Specifications
FeatureDetail
LED Lamp Beads77 PCS SMD2835
Sensing Distance5-8 Meters
Lighting Time8-10 Hours (after full charge)
Charging Time6-8 Hours (in direct sunlight)
BatteryBuilt-in 18650 Lithium Battery, 2400 mAh
MaterialABS
Lighting Modes3 Modes (selectable via remote)
Protection LevelIP65 Waterproof
Installation MethodAssembly (Wall-mounted)
Recommended Installation Height2-3 meters (78.74-118.11 inches)
Dimensions (Approx.)Length: 18.5 cm (7.28 in), Total Height: 8 cm (3.15 in), Bracket Length: 10.5 cm (4.13 in)

For a visual representation of dimensions, please refer to the image below.

Dimensions and specifications table for the solar light
Figure 1: Product Dimensions and Key Specifications

Setup and Installation

  1. Initial Charge: Before first use, ensure the solar panel is free of any protective film. Place the floodlight in direct sunlight for at least 6-8 hours to allow the battery to fully charge.
  2. Choose Installation Location: Select a location that receives ample direct sunlight throughout the day for optimal charging. The recommended installation height is 2-3 meters (78.74-118.11 inches) for effective light coverage and motion sensing.
  3. Mounting the Bracket: Use the provided screws and wall plugs to securely attach the mounting bracket to a wall or suitable surface.
  4. Attach the Floodlight: Slide the floodlight onto the mounted bracket.
  5. Adjust Angle and Direction: Adjust the angle of the solar panel to maximize sun exposure and the direction of the light for optimal illumination and motion sensing coverage. The bracket allows for 360° rotation and 120° vertical adjustment.
Diagram showing the 360 degree rotation of the bracket and sensing area
Figure 2: Bracket Rotation and Sensing Area
Detailed view of the adjustable bracket mechanism
Figure 3: Adjustable Bracket Mechanism
Solar light mounted on a brick wall, highlighting its features
Figure 4: Example Wall Installation

Operation

The floodlight can be operated using the included remote control or the manual ON/OFF switch located on the unit.

Remote Control Functions

Image of the remote control with ON, OFF, Mode 1, Mode 2, Mode 3 buttons
Figure 5: Remote Control
  • ON/OFF: Turns the light on or off.
  • MODE 1: Activates Mode 1.
  • MODE 2: Activates Mode 2.
  • MODE 3: Activates Mode 3.

WARNING: The remote control contains a button cell or coin battery. Ingestion Hazard.

Lighting Modes

The floodlight offers three distinct lighting modes, selectable via the remote control:

Diagram illustrating three lighting modes: Mode 1, Mode 2, Mode 3
Figure 6: Three Optional Lighting Modes
  • Mode 1 (Motion Sensor High Light): The light remains OFF when no motion is detected. When motion is detected within 5-8 meters, the light turns on at high brightness for approximately 15-30 seconds, then turns off. This mode is recommended for energy saving, especially during winter or periods of short sunlight.
  • Mode 2 (Dim Light + Motion Sensor High Light): The light stays in a dim state when no motion is detected. When motion is detected within 5-8 meters, the light switches to high brightness for approximately 15-30 seconds, then returns to dim light.
  • Mode 3 (Always Dim Light): The light stays in a continuous dim light state throughout the night, regardless of motion detection.

Manual ON/OFF Switch

A manual ON/OFF switch is located on the unit, typically near the motion sensor. Ensure this switch is in the 'ON' position for the solar light to function. If the power switch is turned off, the LED light will not light up day or night.

Close-up of the light's front with the solar panel, motion sensor, and ON/OFF switch
Figure 7: Manual ON/OFF Switch Location

Maintenance

  • Cleaning: Regularly clean the solar panel with a soft, damp cloth to remove dust, dirt, or debris. A clean panel ensures optimal charging efficiency.
  • Placement: Ensure the product is placed in a well-ventilated and dry location. Avoid placing it in damp or excessively hot areas.
  • Battery Care (Long-term Storage): If the product is not in use for an extended period, place it in a sunny location to charge for at least one full day every month. This helps maintain battery functionality and prolongs its lifespan.
  • Waterproof Rating: The light has an IP65 waterproof rating, meaning it is protected against dust and low-pressure water jets. While it can withstand rain, avoid submerging it in water.
Solar light shown in rainy conditions, demonstrating IP65 waterproof rating
Figure 8: IP65 Waterproof Protection

Troubleshooting

Common Issues and Solutions
ProblemPossible CauseSolution
Light does not turn on at night.1. Insufficient initial charge.
2. Solar panel covered or dirty.
3. Manual ON/OFF switch is OFF.
4. Not enough sunlight for daily charging.
1. Ensure initial charge of 6-8 hours in direct sunlight.
2. Clean the solar panel and ensure it's not obstructed.
3. Check the manual ON/OFF switch and set it to ON.
4. Relocate the light to an area with more direct sunlight.
Light turns on but quickly turns off, or stays dim.1. Battery charge is low.
2. Incorrect lighting mode selected.
1. Ensure the solar panel receives adequate sunlight for charging. Allow a full day's charge.
2. Select a different mode using the remote control (e.g., Mode 1 for motion-activated only).
Motion sensor is not detecting movement effectively.1. Sensor obstructed.
2. Incorrect angle/height.
1. Ensure the sensor is clear of obstructions.
2. Adjust the light's angle and height to optimize sensing range (5-8 meters).
Remote control is not working.1. Battery in remote is dead.
2. Remote not pointed correctly.
1. Replace the button cell battery in the remote control.
2. Ensure direct line of sight to the light's receiver. Note: The light can be operated manually if the remote is unavailable.
Light stops charging after a few months.1. Solar panel degradation or obstruction.
2. Battery degradation.
1. Clean the solar panel thoroughly. Ensure it's not shaded by new foliage or structures.
2. If the battery is old, its capacity may have diminished. Consider replacing the internal 18650 battery if accessible and within warranty.

User Tips

  • For extended battery life and continuous operation throughout the night, consider using Mode 2 (Dim Light + Motion Sensor High Light). This mode provides constant low-level illumination and brightens when motion is detected, balancing visibility and energy conservation.
  • The remote control significantly enhances convenience, allowing you to switch modes or power the light on/off without needing to reach the unit. Keep it in a safe place.
  • The dummy security camera design can act as a powerful visual deterrent. Position the light prominently to maximize this effect.
  • If you experience reduced performance, always start by ensuring the solar panel is clean and receiving maximum direct sunlight.

Warranty and Support

This product is designed for durability and performance. Specific warranty details may vary by retailer. Please refer to your purchase documentation for warranty information.

For further assistance or detailed instructions, you may refer to the comprehensive user manual available in PDF format: View User Manual (PDF).

If you encounter issues not covered in this manual, please contact the seller or your point of purchase for support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.