Introduction
Thank you for choosing the Milfra Tuya Zigbee Push Button Smart Light Switch. This manual provides essential information for the safe installation, operation, and maintenance of your new smart switch. Please read it thoroughly before installation and keep it for future reference.
Important Safety Information
- Always turn off power at the circuit breaker before installation, removal, or maintenance. Failure to do so may result in serious injury or death.
- Consult a qualified electrician if you are unsure about any part of the installation process or have questions about electrical wiring.
- This device is designed for indoor use only. Do not expose it to moisture or extreme temperatures.
- Ensure all wire connections are secure to prevent short circuits or electrical hazards.
Pre-Installation Notes
- Neutral Wire Required: This smart switch requires a neutral wire for operation. Please ensure your electrical box has a neutral wire (typically white) available.
- Wi-Fi Network: The switch supports 2.4GHz Wi-Fi networks only (IEEE802.15.4 Zigbee). It is not compatible with 5.0GHz networks. Ensure your home Wi-Fi is configured to 2.4GHz or has a mixed mode.
- Circuit Type: Designed for single-pole/one-way circuits only. Not compatible with 3-way or multi-location switch setups.
- Load Type: Applicable only to control lamps. Not recommended for other electrical breakers or heavy-duty appliances.
- Electrical Knowledge: Basic electrical wiring knowledge or experience is required. If you are unsure, please consult a professional electrician.
Installation Guide
Before you begin, ensure you have turned off the power at the circuit breaker.
- Step 1: Turn Off Circuit Breaker. Locate your light's control in your circuit breaker panel and turn it off. Verify power is off by flipping your light switch a few times.
- Step 2: Find the Neutral Wire. In the wall cassette, look for one or more white wires secured with a wire nut. This is your neutral wire. If you cannot find a neutral wire, you will need to consult a professional electrician.
- Step 3: Label Your Wires. Before removing your old switch, mark or record the corresponding Line (Live) and Load wires for easy identification.
- Step 4: Install the Smart Switch. Use wire-nuts to connect the smart switch wires to your home's wires according to the wiring diagram below. Carefully match the Line and Load wires. Remove any protective stickers. Screw the switch into the wall box and then attach the faceplate.
- Step 5: Turn On Circuit Breaker. Restore power to your switch from the circuit breaker. Press the switch a few times to ensure it works.
- Step 6: Check the Wi-Fi Light. The indicator light on the switch should blink rapidly (approximately 2 times per second), indicating it's ready for pairing.
Wiring Diagram

Product Variants

App Setup and Device Pairing
- Step A: Install the 'Smart Life' App. Search for 'Smart Life' in the Apple App Store or Google Play Store, or scan the QR code provided in the product packaging to download and install the app.
- Step B: Register or Log In. Open the Smart Life app. If you are a new user, register for an account using your email address or phone number. If you already have an account, simply log in.
- Step C: Add the Switch to the Smart Life App. Tap the '+' button in the top right corner of the app's home page to add a device. Select 'Switch (Zigbee)' from the device list to proceed. Ensure your phone is connected to your 2.4GHz home Wi-Fi network.
- Step D: Name the Switch. Once the device is successfully added, you can give it a custom name (e.g., 'Living Room Light'). This name will be used for voice control with smart assistants.

Operating Instructions
Voice Control
Your Milfra Smart Switch is compatible with Amazon Alexa and Google Assistant, allowing you to control your lights with simple voice commands.

APP Remote Control
Control your lights from anywhere using the Smart Life app on your smartphone or tablet. You can turn lights on/off, set schedules, and create scenes.
Scheduling
Set custom schedules within the Smart Life app to automatically turn your lights on or off at specific times, enhancing convenience and energy efficiency.

Scene Patterns
Create and configure different scene patterns (e.g., 'Home Mode', 'Away Mode', 'Sleep Patterns', 'Theater Mode') to control multiple lights or devices with a single tap in the app.
Physical Button Operation
The physical buttons on the switch allow for manual control of your lights, providing a traditional way to operate them even without app or voice control.

Maintenance
- Clean the switch surface with a soft, dry cloth. Do not use abrasive cleaners, solvents, or harsh chemicals, as these may damage the finish.
- Ensure the switch is kept dry and away from moisture. Avoid installing in areas with high humidity.
- Regularly check for any loose connections or signs of wear. If any issues are found, consult a qualified electrician.
Troubleshooting
- No Neutral Wire: If you cannot find a neutral wire in your wall cassette, this switch cannot be installed. Consult a professional electrician for assistance or to determine if your wiring can be modified.
- Wi-Fi Connection Issues: Ensure your Wi-Fi network is 2.4GHz. The switch does not support 5.0GHz networks. Check your router settings to confirm you are connected to a 2.4GHz band. Move the switch closer to your Wi-Fi router if signal strength is weak.
- Switch Not Responding: Check if the circuit breaker is on. If the switch is powered but unresponsive, try resetting it.
- Resetting the Switch: To reset your smart switch to factory defaults, long press any ON/OFF button for 7-10 seconds until the indicator light blinks rapidly. This will erase all previous settings and put the switch into pairing mode.
- Indicator Light Status:
- Rapid blinking (2 times/second): Ready for pairing.
- No light: Power off, device not functioning, or in an unpowered state.
Specifications
| Attribute | Value |
|---|---|
| Brand Name | Milfra |
| Model Number | KS811 |
| Switch Type | Push Button Switch |
| Is Smart Device | Yes |
| Material | Plastic |
| Current | 10A |
| Rated Voltage | AC100V-250V (50/60Hz) |
| Load Power (INC) | 600W (Max)/Gang |
| Load Power (LED) | 150W (Max)/Gang |
| Wireless Standard | IEEE802.11 b/g/n (Zigbee) |
| Working Frequency | 2.412-2.484 GHz |
| Product Size | 116*75*35mm |
| Certification | RoHS, FCC, CE |
| Warranty | 1 Year |
| Origin | Mainland China |
User Tips
- Single-Pole Use Only: This switch is designed exclusively for single-pole (one-way) circuits. It cannot be used as a 3-way switch for stair lighting or other multi-location control setups. Attempting to use it in a 3-way configuration may cause damage or malfunction.
- Home Assistant Integration: While not officially stated, Zigbee devices often have community support for integration with home automation platforms like Home Assistant. For specific integration guides and compatibility, refer to Home Assistant community forums and documentation.
Warranty and Support
This Milfra Smart Switch comes with a 1-year warranty from the date of purchase, covering manufacturing defects. Please retain your proof of purchase for warranty claims.
For detailed warranty terms, advanced troubleshooting, or further assistance, please refer to the complete user manual available as a PDF:
Milfra Smart Switch User Manual (PDF)
You can also check the 'Help Center' section within the Smart Life app for solutions to common issues and frequently asked questions.