HORACO HC-SWTG124AS

Contents

HORACO HC-SWTG124AS 2.5GbE Smart Managed Switch User Manual

Model: HC-SWTG124AS

1. Introduction

This manual provides comprehensive instructions for the installation, configuration, operation, and maintenance of your HORACO HC-SWTG124AS 2.5GbE Smart Managed Switch. It is intended for network installers, system administrators, and users familiar with basic networking concepts.

The HORACO HC-SWTG124AS is a 6-port smart managed switch featuring four 2.5G RJ45 Ethernet ports and two 10G SFP+ slots, designed for high-performance networking environments such as home labs, small offices, and advanced network setups. It supports various management functions including VLAN, QoS, LACP, and more.

Front view of HORACO 2.5GbE Smart Managed Switch
Front view of the HORACO 2.5GbE Smart Managed Switch, highlighting its 2.5G RJ45 and 10G SFP+ ports, along with CE, FCC, and RoHS certifications.

2. Safety Information

Please read and follow these safety guidelines to prevent injury and damage to the device:

  • Ensure the power supply voltage matches the device's requirements (DC 12V1A).
  • Do not open the device casing; refer servicing to qualified personnel.
  • Keep the device away from water, fire, and high temperatures.
  • Ensure proper ventilation to prevent overheating.
  • Use only the provided power adapter or a compatible replacement.
  • Avoid placing heavy objects on the device.

3. Package Contents

Verify that your package contains the following items:

  • HORACO HC-SWTG124AS 2.5GbE Smart Managed Switch
  • Power Adapter (EU/US/UK/AU Adapter, depending on selection)
  • User Manual (PDF available online)

4. Product Overview

4.1. Physical Description

The HORACO HC-SWTG124AS is a compact, metal-cased switch designed for durability and efficient heat dissipation.

Top-down view of the switch
Top-down view of the switch, showing the four 2.5G RJ45 ports and two 10G SFP+ ports.

4.2. Ports and Indicators

The switch features the following ports and LED indicators:

  • PWR LED: Indicates power status.
  • Ports 1-4 (2.5G RJ45): Four 10/100/1000/2500Mbps RJ45 ports.
  • Ports 5-6 (10G SFP+): Two 1G/2.5G/10G SFP+ slots for fiber or DAC connections.
  • Reset Button: Located at the rear, used to restore factory defaults.
  • DC 12V Power Input: Power connector.
Side view of switch with power and reset
Side view of the switch, showing the ventilation holes, DC 12V power input, and a reset button.

5. Specifications

Attribute Value
Brand NameHORACO
Model NumberHC-SWTG124AS
Switch TypeEthernet
CertificationCE, FCC, RoHS
Transmission Rate10/100Mbps/1G/2.5G/10Gbps
Switch Capacity60Gbps
Communication ModeFull-Duplex & Half-Duplex
FunctionQoS, VLAN Support
Ethernet Ports4*2.5G RJ45 ports, 2*10G SFP+ ports
SFP+ Port Support10M/100M/1G/2.5G/10G
Packet Forwarding Rate44.64Mpp
MAC Address Table4K
Forwarding ModeStore and forward
Network ProtocolIEEE802.3, IEEE802.3u, IEEE802.3x, IEEE802.3ab, IEEE802.3bz
Working EnvironmentWorking Temperature: -10-50°C; Storage Temperature: -40-85°C; Working Humidity: 10%-90%, non-condensing; Storage Humidity: 5%-95%, non-condensing;
Power VoltageAdapter input voltage: AC 100-240 V; switch input voltage: DC 12V1A

6. Initial Setup

  1. Unpack the Switch: Carefully remove the switch and accessories from the packaging.
  2. Connect Network Cables:
    • Connect your network devices (computers, NAS, WiFi APs, routers) to the RJ45 ports (1-4) using Ethernet cables.
    • For higher bandwidth connections, insert compatible SFP+ modules (1G/2.5G/10G) into ports 5 and 6, then connect fiber optic cables or DAC cables.
  3. Connect Power: Connect the power adapter to the DC 12V input port on the switch, then plug the adapter into a power outlet. The PWR LED should illuminate.
  4. Verify Connections: Check the link/activity LEDs on the connected ports to ensure proper network connectivity.
Switch connected to devices
The switch connected to various devices via Ethernet cables, with the power indicator lit green.

7. Web Management Login

The switch can be managed via a web-based graphical user interface (GUI).

  1. Connect your PC: Connect your computer directly to any of the switch's RJ45 ports.
  2. Configure PC IP Address: Ensure your PC's IP address is in the same network segment as the switch but has a different IP. For the first login, set your PC's IP address to 192.168.2.x (where x is between 1 and 254, but not 1) and the subnet mask to 255.255.255.0.
  3. Access Web Interface: Open a web browser (Chrome 23.0+, Firefox 20.0+, or IE 9.0+) and type the default switch IP address: http://192.168.2.1 into the address bar, then press Enter.
  4. Login: A login window will appear. Enter the default username admin and password admin. Click "Log in" to access the switch system.
Device label with model, IP, username, password
The device label on the bottom of the switch provides the default IP, username, and password.
Support Web Management screenshot
The web management interface provides access to various configuration options.

Important Note: The web management interface is HTTP only and is broadcasted on all ports regardless of VLAN configuration. This may require careful consideration when integrating with firewalls.

8. Configuration

The web interface provides various menus for system configuration. The main menu items are System, Configuration, Security, Monitoring, and Tools, each containing submenus.

8.1. System Settings

8.1.1. Information

Displays basic system information including model, MAC address, IP address, firmware version, and hardware version.

Web interface screenshot (Home/Device Info)
Screenshot of the Device Info and Port Status in the web management interface.

8.1.2. IP Setting

To change the management IP address:

  1. Navigate to System > IP Setting.
  2. Change the IP Address, Netmask, and Gateway as required.
  3. Click Apply.
  4. Crucially, after applying, you must navigate to System Manage > Save Configuration and click Save. Otherwise, the switch will lose the new IP configuration after a power loss.
IP Setting with instructions
Steps to change the IP address and save the configuration.

8.1.3. User Account

To modify the default username and password:

  1. Navigate to System > User Account.
  2. Enter a new username and password, then confirm the new password.
  3. Click Apply.

8.1.4. Port Setting

Allows querying and configuring individual Ethernet ports.

  • State: Enable or disable the port.
  • Speed/Duplex: Configure port speed and duplex mode (e.g., 10M/Half, 100M/Full, 2500M/Full).
  • Flow Control: Enable or disable PAUSE frame reception/transmission to manage network congestion.

8.2. VLAN Configuration

VLANs (Virtual Local Area Networks) segment a physical LAN into logical broadcast domains, enhancing security and efficiency. This switch supports 802.1Q VLANs.

8.2.1. 802.1Q VLAN

To configure 802.1Q VLANs:

  1. Navigate to Configuration > VLAN > 802.1Q VLAN.
  2. Enter a VLAN ID (1-4094) and an optional VLAN Name.
  3. Select member ports, tagged ports, and untagged ports for the VLAN.
  4. Click Add/Modify.

Note: VLAN 1 is the default system VLAN and cannot be deleted.

8.2.2. 802.1Q VID (Port VLAN ID)

To set the PVID for a port:

  1. Navigate to Configuration > VLAN > 802.1Q VID.
  2. Select the port and set its PVID.
  3. Configure the accepted frame type for the port.
  4. Click Apply.

8.3. QoS (Quality of Service)

QoS allows prioritizing network traffic to ensure performance for critical applications.

8.3.1. Port to Queue

Sets processing priorities for data frames based on port.

  1. Navigate to Configuration > QOS > Port to Queue.
  2. Select a port and assign it to a queue (1-8).
  3. Click Apply.

8.3.2. Queue Weight

Configures the scheduling algorithm for queues.

  1. Navigate to Configuration > QOS > Queue Weight.
  2. Set the weight for each queue. Strict priority is equivalent to SP; weights 1-15 use WRR (Weighted Round Robin).
  3. Click Apply.

8.4. Loop Detection/Prevention

The switch can detect and prevent network loops.

8.4.1. Loop Protocol

To configure loop detection/prevention:

  1. Navigate to Configuration > Loop > Loop Protocol.
  2. Select the desired function: Off, Loop Detection, Loop Prevention, or Spanning Tree.
  3. Configure Time Interval and Recover Time as needed.
  4. Click Apply.

8.4.2. STP Global

Rapid Spanning Tree Protocol (RSTP) eliminates physical loops in the LAN.

  1. Navigate to Configuration > Loop > STP global.
  2. Configure STP mode, maximum age, hello time, and forward delay.
  3. Click Apply.

8.4.3. STP Port

Configures STP settings for individual ports.

  1. Navigate to Configuration > Loop > STP port.
  2. Configure Path Cost, Priority, P2P, and Edge settings for each port.
  3. Click Apply.

8.5. IGMP Snooping

IGMP Snooping manages and controls multicast groups on Layer 2 devices, optimizing multicast traffic.

IGMP Snooping diagram
Diagram illustrating multicast packet transmission with and without IGMP Snooping.
  1. Navigate to Configuration > IGMP.
  2. Enable or disable IGMP Snooping.
  3. View multicast group entries under "Dump IGMP entry".
  4. Click Apply.

Link Aggregation (LAG) bundles multiple physical Ethernet links into a single logical interface (Eth-Trunk) to increase bandwidth and reliability.

Trunk Group Setting diagram
Diagram illustrating two switches connected via an Eth-Trunk logical link.

8.6.1. Static Mode

Manually configure Eth-Trunk without LACP. All active links participate in data forwarding and share traffic.

  1. Navigate to Configuration > Trunk Group Setting.
  2. Select a Group ID and set the Type to static.
  3. Select the desired member ports.
  4. Click Add/Modify.

8.6.2. LACP Mode

Link Aggregation Control Protocol (LACP) dynamically aggregates and disaggregates links, providing redundant backup.

  1. Navigate to Configuration > Trunk Group Setting.
  2. Select a Group ID and set the Type to LACP.
  3. Select the desired member ports.
  4. Click Add/Modify.

Note: Ensure no member interface is accessing the Eth-Trunk before changing its work pattern.

8.7. Port-based Mirroring

Copies traffic from a source port to a destination port for monitoring and troubleshooting.

  1. Navigate to Configuration > Port-based Mirroring.
  2. Select the Mirror Direction (Rx, Tx, or Both).
  3. Choose the Mirroring Port (destination) and Mirrored Port List (source).
  4. Click Apply.

8.8. Port Isolation

Prevents communication between specified ports, useful for security in multi-user environments.

  1. Navigate to Configuration > Port Isolation.
  2. Select a port and define its isolation group.
  3. Click Apply.

8.9. Bandwidth Control

Restricts data transmission and reception rates on physical interfaces.

  1. Navigate to Configuration > Bandwidth Control.
  2. Select a port, Type (Ingress/Egress), State (Enable/Disable), and set the Rate (Kbps).
  3. Click Apply.

8.10. Jumbo Frame

Sets the Maximum Transmission Unit (MTU) of the port to support larger frames.

  1. Navigate to Configuration > Jumbo Frame.
  2. Set the Jumbo Frame size (e.g., 16383 Bytes).
  3. Click Apply.

8.11. MAC Constraint

Limits the number of MAC addresses learned on a port.

  1. Navigate to Configuration > MAC Constraint.
  2. Select a port, State (Enable/Disable), and Entry Limits.
  3. Click Apply.

8.12. EEE (Energy Efficient Ethernet)

Configures Energy Efficient Ethernet settings.

  1. Navigate to Configuration > EEE.
  2. Select the EEE Function (Enable/Disable).
  3. Click Apply.

8.13. Security Settings

8.13.1. MAC Address

Manages the MAC address table for efficient forwarding.

  • MAC Search: View dynamic MAC address entries.
  • Static MAC: Manually configure static MAC address entries for specific ports.

8.13.2. Storm Control

Prevents network storms caused by excessive broadcast, unknown multicast, or unicast messages.

  1. Navigate to Security > Storm Control.
  2. Select the Storm Type (Broadcast, Multicast, Unicast), Port, State (Enable/Disable), and Rate (Kbps).
  3. Click Apply.

9. Monitoring

9.1. Port Statistics

Displays real-time statistics for each port, including link status, transmitted/received good packets, and bad packets.

  1. Navigate to Monitoring > Port Statistics.
  2. View the statistics for each port. You can clear the statistics if needed.
Web interface screenshot (Port Statistics)
Screenshot of the Port Statistics section in the web management interface.

10. Tools

10.1. Firmware Upgrade

To upgrade the switch firmware:

  1. Navigate to Tools > Firmware Upgrade.
  2. Select the firmware file and click Upgrade.

Caution: Do not power off the device during the upgrade process. Stay on the upgrade page until complete (approx. 1 minute).

10.2. Configuration Backup

To back up the current configuration:

  1. Navigate to Tools > Configuration Backup.
  2. Click Backup to download the configuration file.

To restore a configuration:

  1. Navigate to Tools > Configuration Backup.
  2. Choose the configuration file and click Restore.

10.3. Reset

To restore factory settings:

  1. Navigate to Tools > Reset.
  2. Click Restore. The system will reboot.

10.4. Save Configuration

To save the current running configuration to persistent memory:

  1. Navigate to Tools > Save.
  2. Click Save.

Important: Always save your configuration after making changes to prevent loss of settings upon reboot or power loss.

10.5. Reboot

To restart the switch:

  1. Navigate to Tools > Reboot.
  2. Click Reboot.

10.6. Logout

To exit the web management system:

  1. Navigate to Tools > Logout.
  2. Click Login (on the logout page) to return to the login screen.

11. User Tips

  • Saving Configuration: Always remember to navigate to System Manage > Save Configuration after making any changes, especially to IP settings, to ensure they are retained after a power cycle.
  • SFP+ Module Compatibility: While the SFP+ ports support 1G/2.5G/10G modules, some DAC cables might be picky. If a DAC cable establishes a link but no data passes, try using OM3 SFP+ 10Gbps modules with fiber optic cables for reliable 10Gbps connections.
  • Jumbo Frames: For optimal performance with 2.5Gbps connections, ensure Jumbo Frames are enabled and configured correctly (e.g., 16383 Bytes) on both the switch and connected devices.
  • Web Interface Access: The management GUI is HTTP only and broadcasts on all VLANs. Be mindful of this for network security, especially when integrating with firewalls.
  • Firmware Updates: Firmware updates are not automatically provided. Contact HORACO support for the latest firmware versions.

12. Troubleshooting

  • No Power: Ensure the power adapter is securely connected to both the switch and a working power outlet. Check the PWR LED.
  • No Link/Connectivity:
    • Verify that Ethernet cables are properly connected and undamaged.
    • Check the link/activity LEDs on both the switch and the connected device.
    • Ensure the connected device's network adapter is enabled and configured correctly.
    • For SFP+ ports, ensure compatible SFP+ modules are used and properly seated.
  • Cannot Access Web Interface:
    • Confirm your PC's IP address is in the same subnet as the switch (default: 192.168.2.x, subnet 255.255.255.0).
    • Try pinging the switch's IP address (default: 192.168.2.1).
    • Clear your browser's cache or try a different browser.
    • If the IP address was changed and not saved, the switch might revert to 192.168.2.1 after a power cycle. Reconfigure your PC to access this default IP.
    • If the password was changed and forgotten, a factory reset might be necessary.
  • Configuration Lost After Power Cycle: This is a known issue if the configuration is not explicitly saved. Always go to Tools > Save after making any changes.
  • Slow Network Performance:
    • Check port statistics for errors or high utilization.
    • Ensure Jumbo Frames are enabled if your network devices support them.
    • Verify that QoS settings are correctly configured if prioritizing traffic.
    • Check for network loops and enable loop prevention if necessary.
  • SFP+ Modules Getting Hot: It is normal for SFP+ modules, especially 10GBase-T RJ45 modules, to generate significant heat. Ensure adequate ventilation around the switch.

13. Warranty and Support

For detailed warranty information and technical support, please refer to the official HORACO website or contact your vendor. A comprehensive user manual in PDF format is available for download:

View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.