Dragon Gauge Digital Car Gauge Series

Contents

User Manual: 2" 52mm Car Digital Gauge Series

Model: Digital Car Gauge Series

Brand: Dragon Gauge

Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of your new 2-inch (52mm) Digital Car Gauge. These gauges are designed to provide accurate and real-time readings of various vehicle parameters, enhancing your driving experience and vehicle monitoring capabilities. Please read this manual thoroughly before installation and use.

Safety Information

  • Always disconnect the vehicle's battery before performing any electrical work to prevent short circuits and electrical shock.
  • Ensure all wiring connections are secure and properly insulated to avoid electrical hazards.
  • Do not attempt to modify the gauge or its components, as this may void the warranty and cause damage.
  • Consult a professional automotive technician if you are unsure about any installation steps.
  • Ensure the gauge is mounted securely and does not obstruct your view or interfere with vehicle controls.

Package Contents

Each gauge package typically includes:

  • 1 x 2" (52mm) Digital Gauge (specific type: Boost, Water Temp, Oil Temp, Oil Press, Voltmeter, EGT, Tachometer)
  • 1 x Power Wiring Harness
  • 1 x Sensor (if applicable for the gauge type, e.g., temperature sensor, pressure sensor)
  • 1 x English Installation Instruction Manual
Assortment of 2-inch digital car gauges showing various readings like water temp, volts, boost, oil press, ext. temp, oil temp, boost psi, and RPM.

Figure 1: Various 2" (52mm) Digital Car Gauges

Setup and Installation

Gauge Dimensions

The gauges have a standard 2-inch (52mm) diameter and a depth of approximately 40mm.

Back view of the gauge with a red line indicating 52mm diameter.

Figure 2: Gauge Diameter (52mm)

Side view of the gauge with a red line indicating 40mm depth.

Figure 3: Gauge Depth (40mm)

Mounting

Choose a suitable location on your dashboard or A-pillar that does not obstruct your view or interfere with driving controls. Ensure the mounting surface is clean and secure. Use a 52mm hole saw for flush mounting or a universal gauge pod for surface mounting (gauge holder sold separately).

Electrical Wiring Instructions

Refer to the wiring diagram below for specific connections for each gauge type. Always ensure the vehicle's battery is disconnected before wiring.

Detailed electrical wiring diagram for various gauges including Boost/Vacuum, Tachometer, Oil/Water Temperature, Air Fuel/Ratio, Oil Pressure, Voltmeter, and Exhaust Gas Temperature.

Figure 4: Electrical Gauges Installation Instructions

Wiring Details (Refer to Figure 4)

  • General Connections:
    • RED wire: Connect to Ignition Switch 12V(+)
    • BLACK wire: Connect to Battery(-) / Ground
  • 6-1-3 Boost/Vacuum Gauge:
    • RED: To Ignition Switch 12V(+)
    • BLACK: To Battery(-)
    • GREEN: To Sensor
    • Connect nylon tubing to the sensor and manifold vacuum source.
  • 6-R Tachometer Gauge:
    • RED(+): To Ignition Switch 12V(+)
    • BLACK: To Battery(-)
    • GREEN: To Sensor (typically the negative terminal of the ignition coil or ECU tachometer output).
    • Note: Compatible with 4, 6, and 8 cylinder gasoline engines.
  • 6-4-5 Oil/Water Temperature Gauge:
    • RED: To Ignition Switch 12V(+)
    • BLACK: To Battery(-)
    • GREEN: To Temp Sensor
  • 6-8 Air Fuel/Ratio Gauge:
    • RED: To Ignition Switch 12V(+)
    • BLACK: To Battery(-)
    • GREEN: To O2 Sensor Signal Wire
  • 6-6 Oil Pressure Gauge:
    • RED: To Ignition Switch 12V(+)
    • BLACK: To Battery(-)
    • GREEN: To Pressure Sensor
  • 6-7 Voltmeter Gauge:
    • RED: To Ignition Switch 12V(+)
    • BLACK: To Battery(-)
  • 6-9 Exhaust Gas Temperature Gauge:
    • RED: To Ignition Switch 12V(+)
    • BLACK: To Battery(-)
    • ORANGE: To Orange wire of EGT sensor
    • GREEN: To Green wire of EGT sensor

Operating Instructions

Once properly installed and wired, turn on your vehicle's ignition. The gauge will power on and display the current reading. The blue LED display provides clear visibility day or night.

  • Reading the Gauge: The large digital numbers indicate the current measurement (e.g., PSI, BAR, °C, Volts, RPM).
  • Warning Indicator: Most gauges feature a "WARNING" text which may illuminate or flash under certain conditions (e.g., exceeding a set threshold for temperature or pressure). Consult your vehicle's specifications for normal operating ranges.

Maintenance

  • Cleaning: Use a soft, dry cloth to clean the gauge face. Do not use abrasive cleaners or solvents, as they may damage the display.
  • Sensor Check: Periodically inspect sensor connections for corrosion or damage. Ensure sensors are securely installed and free from leaks (for pressure/temperature sensors).
  • Wiring Inspection: Check wiring connections periodically to ensure they remain secure and free from fraying or damage.

Troubleshooting

ProblemPossible CauseSolution
Gauge does not power onNo power to RED wire; poor ground connection (BLACK wire); faulty gauge.Check 12V+ connection at ignition switch; ensure BLACK wire has good chassis ground; verify wiring harness is fully connected.
Incorrect or fluctuating readingsLoose sensor connection; faulty sensor; air in pressure line (for oil pressure); incorrect sensor type.Check sensor wiring and connection; ensure sensor is correctly installed; pre-bleed air from pressure senders; verify sensor matches gauge type.
Tachometer not working or incorrect RPMIncorrect connection to ignition coil/ECU; incompatible engine type (e.g., 2-stroke).Verify GREEN wire connection point; ensure engine is 4/6/8 cylinder gasoline type.
Sensor not fitting manifoldIncorrect sensor thread size.Verify the thread size of the sensor and your manifold. Adapters may be required.

Specifications

FeatureSpecification
Gauge Diameter2 inches (52mm)
Gauge DepthApprox. 40mm
Operating Voltage12 Volts DC
MaterialABS Plastic
DisplayDigital Blue LED
Item Weight0.3 kg (approx. per gauge)
Boost Gauge PSI Range-14 to 29 PSI
Boost Gauge BAR Range-1 to 2 BAR
Water/Oil Temp Gauge Range40 to 150 °C
Oil Pressure Gauge PSI Range0 to 150 PSI
Oil Pressure Gauge BAR Range0 to 7 BAR
Voltmeter Range0 to 15 V
Exhaust Gas Temp Gauge Range0 to 1300 °C
Tachometer RPM Range0 to 9999 RPM (for 4/6/8 cylinder gasoline cars)

User Tips

  • Tachometer Compatibility: The Tachometer gauge is designed for 4, 6, and 8 cylinder gasoline engines. It is not compatible with 2-stroke engines or other engine types.
  • Sensor Thread Sizes: Before installation, verify the thread size of the provided sensor (e.g., oil pressure sensor) matches your vehicle's manifold or port. Adapters may be necessary if there is a mismatch.
  • Pre-Bleed Pressure Senders: For oil pressure gauges, it is recommended to pre-bleed any air out of the sender unit before final installation to ensure accurate readings and prevent fluctuations.
  • Packaging Inspection: Upon receiving your order, carefully inspect the packaging and contents for any damage that may have occurred during transit.

Warranty and Support

For warranty information, technical support, or assistance with troubleshooting, please contact your retailer or the manufacturer directly. Keep your proof of purchase for any warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.