1. Product Overview
The S1-B(WT) is a versatile AC phase-cut dimmer designed for single-color dimmable LED lamps, traditional incandescent, and halogen lights. It offers multiple control options including Tuya Smart APP (WiFi), RF 2.4G remote control, and external push switch. It also supports voice control via Amazon Alexa, Google Assistant, Tmall Genie, and Xiaodu voice assistant.

2. Safety Information
- Ensure all wire connections and polarities are correct and secure before applying power to prevent damage to the controller.
- Installation should be performed by a qualified electrician.
- Do not install in direct sunlight or high-temperature areas.
- Ensure the power is off before installation or maintenance.
- This device is designed for indoor use only.
- Over-heat and over-load protection are built-in, but ensure loads do not exceed specified limits.
3. Specifications
| Parameter | Value |
|---|---|
| Model | S1-B(WT) |
| Input Voltage | AC100-240V |
| Output Voltage | AC100-240V |
| Output Current | Max 1.5A |
| Output Power | 150-360W |
| Input Signal | WiFi + RF + Push Dim |
| Control Distance | 30m (Barrier-free space) |
| Dimming Level | 256 levels |
| Dimming Range | 0-100% |
| Operation Temperature | Ta: -20°C ~ +55°C |
| Case Temperature (Max) | Tc: +85°C |
| IP Rating | IP20 |
| Warranty | 5 years |
| Protection | Overheat / Over-load |
| Material | ABS |
| Support APP | Tuya or Smart Life APP |
4. Setup
4.1 Wiring Diagram
Before wiring, ensure the main power supply is turned off. Connect the dimmer according to the diagram below. This dimmer supports both dimmable LED lights and Triac dimmable LED drivers.

4.2 Dimming Edge Setting (Leading Edge / Trailing Edge)
The S1-B(WT) dimmer can be set to leading edge (forward-phase) or trailing edge (reverse-phase) dimming using a DIP switch on the device. Select the appropriate mode based on your dimmable LED light or driver before powering on the device.

4.3 Tuya Smart APP Network Connection
The S1-B(WT) connects directly to the Tuya APP via Wi-Fi, eliminating the need for a separate gateway.

- Smart Config Mode: Press and hold the Match/Set key for 2 seconds, or quickly press it twice. The blue LED indicator will flash rapidly. This indicates the device is ready for Smart Config pairing.
- AP Config Mode: If Smart Config fails, press and hold the Match/Set key for 5 seconds. The blue LED indicator will flash slowly. This indicates the device is in AP Config mode.
- Once connected successfully, the blue LED indicator will stop flashing, and the device will appear in your Tuya Smart APP.
- Ensure your Wi-Fi router is on the 2.4GHz band, as the 5GHz band is not supported. Keep the dimmer close to your router during setup.
4.4 RF Remote Control Matching (Optional)
You can pair an RF 2.4G remote control with the S1-B(WT) dimmer using one of the following methods:
- Using the S1-B(WT)'s Match Key: Short press the Match key on the S1-B(WT), then immediately press the on/off key (for single zone remotes) or a zone key (for multiple zone remotes) on your RF remote.
- Using Power Restart: Switch off the power to the S1-B(WT), then switch it back on. Repeat this power cycle. Immediately short press the on/off key (or zone key) 3 times on your RF remote. The light will blink 3 times to confirm successful pairing.
4.5 RF Remote Control Deletion
- Using the S1-B(WT)'s Match Key: Press and hold the Match key on the S1-B(WT) for 15 seconds. The light will blink 5 times, indicating all matched remotes have been deleted.
- Using Power Restart: Switch off the power to the S1-B(WT), then switch it back on. Repeat this power cycle. Immediately short press the on/off key (or zone key) 5 times on your RF remote. The light will blink 5 times, indicating all matched remotes have been deleted.
5. Operating Instructions
5.1 APP Control
Once connected to the Tuya Smart APP, you can control the dimmer from your smartphone:
- On/Off: Tap the power icon in the app.
- Brightness Adjustment: Use the brightness slider in the app to adjust the light intensity from 0% to 100%.
- Scheduling & Scenes: Utilize the app's features to set schedules, timers, and create custom scenes for your lighting.

5.2 Voice Control
The S1-B(WT) is compatible with popular voice assistants. Link your Tuya Smart account to your Amazon Alexa or Google Home account to enable voice commands.

- Turn On/Off: