1. Introduction
This manual provides essential information for the safe and effective use of your new Plastic Pipe Fitting. This product is designed to create secure connections between hoses and threaded components in various applications, including fish tanks, irrigation systems, and general fluid transfer. Please read this manual thoroughly before installation and use.
2. Safety First
- Always read this manual carefully before use.
- Keep the product away from fire, excessive heat, water (during storage if not in use), and out of reach of children.
- If you observe any signs of damage to the fitting, discontinue use immediately.
- Retain the original packaging and this instruction manual for future reference.
- Avoid using the product in humid, hot, or flammable environments.
- This product is intended for users over 14 years old. Children should only operate under adult supervision.
3. Product Overview
The Plastic Pipe Fitting is a versatile coupling designed for connecting hoses to threaded ports. It features a pagoda barb on one end for secure hose attachment and a female thread on the other for connection to male threaded components. Made from durable plastic, these fittings are suitable for various fluid transfer needs.

4. Specifications
| Attribute | Value |
|---|---|
| Material | Plastic |
| Type | Coupling |
| Connection Type | Female Thread |
| Head Code | Round |
| Technics | Casting |
| Pressure Rating | <850 kPa |
| High-Concerned Chemical | None |
| Hose Inner Diameter (Barb Sizes) | 4mm, 6mm, 8mm, 10mm, 12mm, 14mm, 16mm, 18mm, 20mm, 25mm |
| Female Thread Specifications | 1/4", 3/8", 1/2", 3/4" |
| Origin | Mainland China |
| Certification | NONE |
Detailed Dimensions by Size:
Refer to the following diagrams for precise measurements of each fitting type:






















5. Setup and Installation
5.1 Unpacking Inspection
- Verify all items against your packing list.
- Inspect the product for any signs of damage.
- If any items are missing or damaged, please contact the merchant immediately.
5.2 Installation Steps
- Select the Correct Size: Ensure the pagoda barb size matches the inner diameter of your hose and the female thread matches the male thread of your component.
- Prepare the Hose: If necessary, cut the end of the hose cleanly and squarely. For a tighter fit, you may briefly warm the end of the hose in hot water to make it more pliable.
- Attach Hose to Barb: Push the hose firmly onto the pagoda barb. Ensure it goes past at least two barbs for a secure connection. For high-pressure applications, a hose clamp is recommended (not included).
- Connect Threaded End: Screw the female threaded end of the fitting onto the corresponding male threaded component. Hand-tighten first, then use a wrench for a snug fit, being careful not to overtighten the plastic threads.
- Seal (Optional but Recommended): For a leak-proof seal on the threaded connection, apply PTFE tape (Teflon tape) or a suitable thread sealant to the male threads before assembly. Note: Sealing gaskets are not typically included with these fittings, so external sealant is crucial for preventing leaks.
- Test for Leaks: After installation, slowly introduce fluid into the system and carefully check all connections for leaks. Tighten any leaking connections as needed.
If you are unsure about the installation process, it is recommended to consult a professional or contact the merchant for guidance.
6. Operation
Once properly installed, the plastic pipe fitting functions as a passive connector. It requires no active operation. Ensure that the fluid pressure in your system does not exceed the fitting's rated pressure of <850 kPa.
7. Maintenance
- Regular Inspection: Periodically inspect the fittings and connections for any signs of wear, cracks, or leaks.
- Cleaning: Clean the fittings as needed using mild soap and water. Avoid harsh chemicals that could degrade the plastic material.
- Storage: If the fitting is removed from service, clean it thoroughly and store it in a dry place, away from direct sunlight and extreme temperatures. Keep away from children.
8. Troubleshooting
8.1 Leaks at Connections
- Hose Connection: Ensure the hose is fully seated on the barb. If the hose is loose, consider using a hose clamp or a fitting with a slightly larger barb if the hose has stretched.
- Threaded Connection: Leaks often occur if the threaded connection is not properly sealed. Apply PTFE tape (Teflon tape) or a liquid thread sealant to the male threads before assembly. Ensure the fitting is tightened sufficiently but not overtightened, which can strip plastic threads.
- Damaged Fitting: Inspect the fitting for cracks or damage. Replace if damaged.
8.2 Difficulty Attaching Hose
- Hose Size Mismatch: Ensure the hose inner diameter matches the barb size.
- Stiff Hose: Briefly warm the end of the hose in hot water to make it more flexible for easier attachment.
9. User Tips
- Many users report excellent quality and a perfect fit when the correct thread and barb sizes are chosen. Double-check your measurements before purchasing.
- For applications like irrigation systems, these durable plastic fittings perform well and help prevent leaks when installed correctly.
- Remember that these fittings typically do not come with sealing gaskets. Always use PTFE tape or a thread sealant on the threaded connections to ensure a leak-free setup.
- The plastic material is noted for its durability, but avoid excessive force during installation to prevent stripping threads or cracking the fitting.
10. Warranty and Support
For any issues or support inquiries, please contact the manufacturer or seller directly using the information provided below.
11. Manufacturer Information
Manufacturer: Yueqing Yakai Electronic Commerce Co. Ltd.
Manufacturer Address: 106 Xiangsheng Road, Yanpen Street, Yuaging City, Wenzhou City, Zhejiang Province, China
Manufacturer E-mail: 121486620@qq.com
EU Authorized Representative: SUCCESS COURIER SL
EU Representative Address: ES-CALLE RIO TORMES NUM. 1, PLANTA 1, DERECHA, OFICINA 3, Fuenlabrada, Madrid, 28947 Spain
EU Representative Email: successservice2@hotmail.com
EU Representative Telephone: +34-910602659
Importer: Yueqing Yakai Electronic Commerce Co. Ltd,
Importer Address: 106 Xiangsheng Road, Yanpen Street, Yuaging City, Wenzhou City, Zhejiang Province, China