1. Product Overview
The YS-MT21 is a 2.1-channel digital Bluetooth power amplifier module, featuring left-right main channel output plus an independent subwoofer output. It integrates independent controls for treble, bass, master volume, and subwoofer frequency. It delivers 50W×2 for main channels and 100W for the subwoofer. Supporting wireless Bluetooth audio input, it can be quickly paired with speakers and passive subwoofers to build home desktop audio, car audio, or DIY speaker systems.
2. Specifications
| Feature | Description |
|---|---|
| Model | YS-MT21 K58 |
| Channel Configuration | 2.1-Channel (Left + Right + Subwoofer) |
| Output Power | 50W×2 (Main Channels), 100W (Subwoofer) |
| Audio Input | Wireless Bluetooth, AUX, U disk, USB sound card |
| Adjustable Functions | Master Volume, Treble, Bass, Subwoofer Cut-off Frequency, Subwoofer Volume |
| Operating Voltage | DC 12-24V (19-24V recommended for full power output) |
| Speaker Impedance | 4-8Ω passive speakers / passive subwoofers |
| Bluetooth Version | Bluetooth 5.0 (High-definition for lossless audio transmission) |
| Input Sensitivity | 500mV |
| Protection Features | Static protection, overheat overcurrent, short circuit protection |
| Product Size | 92mm x 90mm x 22mm |
3. Packing List
The product package typically includes:
- YS-MT21 Amplifier Board ×1
- Phillips Screwdriver ×1
- DC Power Terminal Connector ×1
4. Setup and Wiring
4.1. Interface & Knob Overview
Familiarize yourself with the various interfaces and control knobs on the amplifier board:
4.2. Wiring Interfaces
- DC-IN: Power input. Connect the positive pole to "+" and the negative pole to "-". Compatible with DC 12-24V power supply.
- L+L-/R+R-: Left & right main channel outputs for passive main speakers (L=Left, R=Right).
- SUBWOOFER: Subwoofer output for passive subwoofer drivers.
4.3. Control Knobs (From Right to Left)
- MAIN VOLUME: Master volume control. Turn clockwise to increase volume, counter-clockwise to decrease. This knob also functions as the power switch.
- BASS: Bass gain control for overall low-frequency intensity of main channels and subwoofer.
- TREBLE: Treble control to adjust brightness of main channel high frequencies.
- SUBWOOFER VOLUME: Independent volume control for subwoofer output.
- SUBWOOFER FREQ: Subwoofer cut-off frequency control, to match different-size subwoofer drivers.
5. Operating Instructions
5.1. Installation & Wiring Steps
- Wire with Power Off: Always complete all wiring with power disconnected to avoid short-circuit damage.
- Connect Speakers:
- Left/Right Main Speakers: Connect to L+ L- and R+ R- terminals respectively. Ensure correct polarity (do not reverse positive and negative poles).
- Subwoofer: Connect speaker wire to the SUBWOOFER output terminal.
- Connect Power: Attach the DC power terminal to DC-IN (observe polarity), then connect to a 12-24V DC regulated power adapter.
5.2. Bluetooth Pairing
- Power On & Pair: The module automatically enables Bluetooth after power-on. Search for its Bluetooth name (typically "YS Audio") on your phone/PC or other Bluetooth device and pair for audio playback.
5.3. Sound Adjustment
- Sound Adjustment: Adjust the master volume, treble, bass, subwoofer volume, and subwoofer frequency during playback to achieve optimal sound quality according to your preferences and speaker setup.
5.4. Switching Audio Input Modes
The module defaults to line-in (AUX) mode out of the box. To switch to Bluetooth mode, insert a 3.5mm audio jack into the AUX-in port and then immediately remove it. The module should announce "Bluetooth mode" and become discoverable for pairing. It will remain in Bluetooth mode until an AUX cable is re-inserted.
6. Maintenance and Precautions
- Use only a DC regulated power supply. Do not exceed 24V, and never reverse power polarity to prevent burnout.
- Use speakers with 4-8Ω impedance only. Speakers below 4Ω may overload the module and cause damage.
- Keep exposed wire strands short during wiring to avoid short-circuit between positive and negative wires, which can damage the board.
- The module generates heat during operation. Ensure good ventilation and do not seal it in an enclosed space. Avoid prolonged high-volume use without adequate heat dissipation.
- Never plug or unplug speaker wires while the module is powered on, as transient current may damage the amplifier chip.
- If Bluetooth fails to connect, restart the module and re-pair your device.
7. Troubleshooting
- No sound after power-on: Check power polarity and voltage, verify Bluetooth pairing status, and inspect speaker wiring for any short-circuits.
- Main channels work but no subwoofer output: Check the subwoofer wiring, ensure the subwoofer volume knob is turned up, and verify the subwoofer frequency adjustment.
- Distorted or crackling sound: Reduce the master volume. If the issue persists, replace with a higher-power power supply and check for proper speaker impedance matching.
- Unstable Bluetooth connection: Move away from potential signal interference sources, shorten the distance between your device and the module, restart Bluetooth on both devices, and re-pair.
8. User Tips
- Bluetooth Mode Activation: If the module defaults to line-in mode, you can force it into Bluetooth mode by briefly plugging and unplugging a 3.5mm audio jack into the AUX-in port. The module will then announce "Bluetooth mode" and be ready for pairing.
- Power Supply Flexibility: The amplifier board can be powered by a laptop power adapter or a car battery, provided the voltage is within the DC 12-24V range. A 24VDC 10A power source is suitable for optimal performance.
- Addressing Noise: If you experience noise, especially at higher volumes, ensure your power supply is stable and provides sufficient current. Also, double-check that your speakers' impedance matches the recommended 4-8Ω range.
9. Warranty and Support
For detailed warranty information, technical support, or any product-related inquiries, please refer to the official product page or contact the seller directly. A comprehensive user manual is also available in PDF format for download: User Manual (PDF).
10. Product Video
Watch this video for a visual demonstration of the amplifier board's features and operation: