GGBEE B22 LED Motion Sensor Bulb

Contents

B22 LED Motion Sensor Light Bulb User Manual

Models: 12W, 15W, 18W, 20W

1. Product Introduction

This GGBEE LED light bulb integrates a PIR (Passive Infrared) motion sensor, designed to automatically turn on when motion is detected in dark environments and turn off after a period of inactivity. It is suitable for various indoor lighting scenarios such as corridors, pathways, stairs, gardens, and parking areas.

2. Setup and Installation

Important: Ensure the power supply is disconnected before installation to prevent electric shock.

  1. Verify Socket Type: This bulb features a B22 bayonet base. Ensure your light fixture is compatible with B22 sockets.
  2. Disconnect Power: Turn off the main power switch to the light fixture where you intend to install the bulb.
  3. Install Bulb: Align the bulb's B22 base with the socket. Push the bulb into the socket and twist clockwise until it locks securely into place. Do not overtighten.
  4. Restore Power: Turn the main power switch back on. The bulb is now ready for operation.
B22 Bayonet Base
Figure 1: B22 Bayonet Base Type

Safety Precautions:

  • Always cut off power before installing or replacing the bulb.
  • After the bulb has been on, it may be hot. Avoid touching it directly to prevent burns.
  • Do not use the bulb under overload conditions. Replace promptly if damaged or aging.
  • Do not attempt to disassemble the light bulb unless you are a qualified professional.

3. Operating Instructions

This LED bulb features an integrated PIR motion sensor that operates based on ambient light conditions and motion detection.

Motion Sensor Detection Area
Figure 2: Motion Sensor Detection Angle (120°) and Distance (5 meters)
  • Automatic Operation: The bulb will only activate in dark environments. During daylight or in well-lit areas, the sensor will keep the light off to save energy.
  • Motion Detection: When motion is detected within its sensing range (3-5 meters) and angle (120°) in a dark environment, the bulb will automatically turn on.
  • Continuous Lighting: The light will remain on as long as continuous motion is detected within its range.
  • Automatic Turn-Off: After motion ceases, the bulb will remain lit for approximately 30-60 seconds (40-60s typical) before automatically turning off.
Operating Mode Diagram
Figure 3: Operating Mode - Day (Off), Night (On with motion), Stays on with motion, Turns off after 30-45s of no motion.

4. Maintenance

  • Cleaning: Ensure the bulb and its sensor lens are kept clean from dust and debris to maintain optimal performance. Use a soft, dry cloth for cleaning. Do not use liquid cleaners directly on the bulb.
  • Replacement: If the bulb flickers, dims significantly, or stops working, it may have reached the end of its lifespan or be damaged. Replace it with a new compatible bulb.
  • Avoid Overload: Do not connect the bulb to circuits that exceed its specified voltage or wattage limits.

5. Troubleshooting

ProblemPossible CauseSolution
Bulb does not light upNo power, loose connection, too much ambient light, faulty bulb.Check power supply. Ensure bulb is securely tightened in socket. Test in a completely dark environment. Replace bulb if faulty.
Bulb stays on continuouslyConstant motion in detection area, sensor obstruction, faulty sensor.Ensure no continuous motion (e.g., pets, moving curtains) is within range. Clear any obstructions from the sensor lens. If problem persists, the sensor may be faulty.
Bulb lights up during the daySensor malfunction or insufficient ambient light.Ensure the sensor is not covered or obstructed. If the area is still too dark, the sensor may activate. If problem persists, sensor may be faulty.
Bulb flickersUnstable power supply, loose connection, bulb nearing end of life.Check power supply stability. Ensure secure connection. Replace bulb if it's old or damaged.

6. Specifications

FeatureSpecification
BrandGGBEE
Model TypeLED bulb (Bubble Ball Bulb)
Base TypeB22
Power SourceAC
VoltageAC 85-265V (Universal)
Wattage Options12W, 15W, 18W, 20W
LED Chip Model2835SMD
Emitting ColorWarm White (2800K~3500K), White (5800K~6500K)
Luminous Flux60-249 Lumens (general), 500-999 Lumens (specific range)
Color Rendering Index (CRI)>85
Body MaterialPC + ABS
Detection Angle120 degrees
Detection Distance3-5 meters
Lasting Time (after motion ceases)30-60 seconds
Lifespan>10 years
CertificationCE
Is Smart DeviceNo
Dimensions (12W)60mm (Diameter) x 117mm (Height)
Dimensions (15W)60mm (Diameter) x 122mm (Height)
Bulb Dimensions and Specification Table
Figure 4: Detailed Specifications and Dimensions

7. User Tips

  • Brightness: The 20W version is noted for being very bright and responsive, turning on quickly when motion is detected. Choose wattage according to your brightness needs.
  • Sensor Duration: The light typically stays on for about 1 minute (or 30-60 seconds) after motion ceases, which is generally sufficient for most applications like hallways or staircases.
  • Placement: For optimal performance, place the bulb where the sensor has an unobstructed view of the area you want to monitor. Avoid placing it near heat sources or in direct sunlight, which can interfere with sensor operation.

8. Frequently Asked Questions (FAQ)

Q: How many bulbs are included in one package?
A: Typically, one bulb is included per package unless explicitly stated as a multi-pack or set by the seller.
Q: Can this bulb be used in countries with different voltages, like Mexico?
A: Yes, this bulb supports a wide voltage range of AC 85-265V, which is compatible with standard household voltages in most countries, including Mexico (typically 127V).

9. Warranty and Support

For any issues not resolved by the troubleshooting guide, or for further assistance, please contact the seller or customer support where you purchased the product. Provide your order details and a description of the issue for prompt service.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.