MANUALS+

Adult content warning

RETEKESS TD177 Restaurant Pager Calling System User Manual

Why this warning: This page discusses adult sexual products and may include explicit descriptions or images.

Leave this page

RETEKESS TD177

Contents

RETEKESS TD177 Restaurant Pager Calling System User Manual

Model: TD177 | Brand: RETEKESS

1. Introduction

This manual provides detailed instructions for the setup, operation, maintenance, and troubleshooting of your RETEKESS TD177 Restaurant Pager Calling System. Please read this guide thoroughly before use to ensure optimal performance and longevity of the product.

The TD177 system is designed to streamline guest queuing and service calls in various environments such as restaurants, food trucks, cafes, and bars. It features a transmitter keypad and multiple pagers that alert guests when their order is ready or service is required.

Video: Overview of the RETEKESS TD177 Restaurant Pager System, demonstrating its components and basic functions.

2. Safety Warnings and RF Energy Exposure Guide

Before using this device, please read this guide which contains important operating instructions for safe usage, control information and operational instructions for compliance with RF Energy Exposure limits in applicable national and international standards. User instructions should accompany the device when transferred to other users.

2.1. Unauthorized Modification and Adjustment

Changes or modifications not expressly approved by the party responsible for compliance may void the user's authority granted by the local government radio management departments to operate this radio and should not be made. To comply with the corresponding requirements, transmitter adjustments should be made only by or under the supervision of a person certified as technically qualified to perform transmitter maintenance and repairs in the private land mobile and fixed services as certified by an organization representative of the user of those services. Replacement of any transmitter component (crystal, semiconductor, etc.) not authorized by the local government radio management departments equipment authorization for this radio could violate the rules.

2.2. FCC Compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

2.3. IC Compliance (Licence-exempt radio apparatus)

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

This radio transmitter has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

2.4. CE Compliance

HENAN ESHOW ELECTRONIC COMMERCE CO., LTD declares that the radio equipment type is in compliance with the essential requirements and other relevant provisions of RED Directive 2014/53/EU and the ROHS Directive 2011/65/EU and the WEEE Directive 2012/19/EU; the full text of the EU declaration of conformity is available at www.retekess.com.

This product may be used in the following countries and regions: Belgium (BE), Bulgaria (BG), Czech Republic (CZ), Denmark (DK), Germany (DE), Estonia (EE), Ireland (IE), Greece (EL), Spain (ES), France (FR), Croatia (HR), Italy (IT), Cyprus (CY), Latvia (LV), Lithuania (LT), Luxembourg (LU), Hungary (HU), Malta (MT), Netherlands (NL), Austria (AT), Poland (PL), Portugal (PT), Romania (RO), Slovenia (SI), Slovakia (SK), Finland (FI), Sweden (SE) and United Kingdom (UK).

2.5. Disposal Information

The crossed-out wheeled-bin symbol on your product, literature, or packaging reminds you that all electrical and electronic products, batteries, or accumulators must be taken to designated collection locations at the end of their working life. Do not dispose of these products as unsorted municipal waste. Dispose of them according to the laws and rules in your area.

2.6. RF Safety

This two-way radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide communications between two or more users over a distance. RF energy, which when used improperly, can cause biological damage. Please refer to the following websites for more information on what RF energy exposure is and how to control your exposure to assure compliance with established RF exposure limits: www.who.int/en/.

Keeping the radio at a proper distance is important as RF exposure decreases with increasing distance from the proper antenna. A proper antenna is an antenna supplied with this radio by the manufacturer or specifically authorized by the local authority for use with this radio. This radio can only be operated by use of an antenna of a type and maximum (or lesser) gain approved for the transmitter under regulations and rules. This transmitter must operate with the antenna(s) documented and in Push-to-Talk and body-worn configurations as documented. Using authorized accessories is important because the use of Non-Retevis accessories may result in exposure levels, which exceed the IEEE/ICNIRP RF exposure limits.

Transmit no more than the rated duty factor 50% of the time. Transmitting necessary information or less, is important because the radio generates measurable RF energy exposure only when transmitting in terms of measuring for standards compliance. For users who wish to further reduce their exposure, some effective measures to reduce RF exposure include:

  • Reduce the amount of time spent using your wireless device.
  • Use a speakerphone, earpiece, headset, or other hands-free accessory to reduce proximity to the head (and thus head exposure). While wired earpieces may conduct some energy to the head and wireless earpieces also emit a small amount of RF energy, both wired and wireless earpieces remove the greatest source of RF energy (handheld device) from proximity to the head and thus can greatly reduce total exposure to the head.
  • Increase the distance between wireless devices and your body.

This radio is designed for and classified as "General population/uncontrolled use". General population/uncontrolled environments are defined as locations where there is exposure of individuals who have no knowledge or control of RF exposure level.

2.7. Electromagnetic Interference/Compatibility

Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed, or otherwise configured for electromagnetic compatibility. During transmissions, your radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so, such as hospitals or healthcare facilities.

Turn off your radio in the following conditions:

  • Turn off your radio prior to entering any area with a potentially hazardous or explosive atmosphere. Only radio types that are especially qualified should be used in such areas as "Intrinsically Safe".
  • Turn off your radio when taking on fuel or parked at gasoline service stations.
  • Turn off your radio when on board an aircraft. Any use of a radio must be in accordance with applicable regulations per airline crew instructions. Do not use any radio that has a damaged antenna. If a damaged antenna comes into contact with the skin when the radio is in use, a burn can result. Turn off your radio before removing or installing accessories.
  • When the transceiver is used for long transmissions, the radiator and chassis will become hot.

3. Product Overview

3.1. Transmitter

RETEKESS TD177 Transmitter Diagram
Figure 1: TD177 Transmitter Front View
RETEKESS TD177 Transmitter Back View
Figure 2: TD177 Transmitter Back View with Battery Compartment
RETEKESS TD177 Transmitter Side View
Figure 3: TD177 Transmitter Side View showing USB and DC Power Ports

Transmitter Components:

  1. Digital tube display
  2. Transmit indicator
  3. Keypad area
  4. Battery compartment
  5. Transmit antenna
  6. Power switch
  7. USB-A Female connector (connect to upper computer)
  8. DC power connector

3.2. Pager

RETEKESS TD177 Pager Side View with Mute Key
Figure 4: TD177 Pager Side View showing Mute Key
RETEKESS TD177 Pager in Hand
Figure 5: TD177 Pager held in hand

Pager Components:

  1. Touch button (Mute key)
  2. Digital tube (display pager number)
  3. Charging indicator (red light when charging, green light when fully charged)
  4. Charging contact

3.3. Charging Base

RETEKESS TD177 Charging Base with Pagers
Figure 6: TD177 Charging Base with Pagers
RETEKESS TD177 Charging Base with Green Indicator Lights
Figure 7: TD177 Charging Base showing green indicator lights for charged pagers

Charging Base Components:

  1. Charging slot
  2. Fixing screw holes at the bottom of the charging base for cascade use
  3. Fixing screw holes at the top of the charging base for cascade use
  4. Base button (for changing base ID)
  5. DC power connector (12V)
  6. Power supply plug at the bottom of the charging base cascade
  7. Base pager mounting fixing screw holes
  8. Charging base cascade top power supply socket
  9. Wall mounting holes (maximum diameter 10.5mm)
  10. Anti-slip mat
  11. Anti-tipping base pager
  12. Anti-tipping bottom plate fixed screw holes (M4 screws)

4. Setup

4.1. Transmitter Power On

Insert DC power supply or put in 3x AAA batteries, press the power switch, wait for the screen to display "----" to enter the standby interface.

Click the power button to enter the system menu interface. Enter the user password ("2580" is the manufacturer's super password). Click the up or down arrow to select the menu option, press the [CALL] button to enter the menu option, press the [CALL] button again to save the current parameters, and press the power button to exit the menu interface.

Note: The charging function is not supported when the transmitter is powered by AAA batteries. Please replace the battery in time when the power is low.

4.2. Charging Base Cascade Use

The charging base supports cascading. Align the cascading plug (labeled 8 in diagram 3.1) at the bottom of the charging base with the top jack (labeled 6) of another charging base to be cascaded. Press and insert the plug so that the four screw holes of the cascade are aligned (labeled 3 in diagram 3.1), and then install the fixing screws (M3 big head screws) to fix it.

Note: The charging base's power supply supports up to a maximum of 3 bases in cascade.

4.3. Wall Mounting

Ensure that the spacing of the wall mounting screws is consistent with the wall mounting holes of the charging base, and place the charging base on the wall mounting screws.

The distance between the wall mounting holes is 10cm between left and right, and 10cm between top and bottom.

4.4. Installation of Anti-Tipping Base Plate

  1. Take out the anti-tipping plate, making sure the anti-tipping plate with anti-skid pads faces down, and the top face the bottom of the charging base. Align the four screw holes (labeled 12) on the plate with the four screw holes (labeled 7) on the charging base.
  2. Tighten the fixing screws (M4x25) through the holes of the plate and align them with the holes of the charging base. Secure the remaining three screws in turn. The anti-tipping plate is successfully installed.

5. Operation

5.1. Function Setting

To access function settings, ensure the transmitter is powered on and in standby mode. Use the menu interface to navigate and adjust parameters.

  • 4.2 Setting Prompt Duration [E-00]: Sets the sound, light, and vibration duration of the pager (factory default: 10 seconds).
  • 4.3 Transmitter ID/Channel [E-01]: Sets the system channel (value range: 001-999, default: 001). After modification, reset charging base ID and pager numbers.
  • 4.4 Setting Number Step Length [E-02]: Defines the step value for pager numbering (factory default: 001).
  • 4.5 Pager Flashing Light Prompt On/Off [E-03]: Toggles pager flashing light (N: open, F: close, factory default: N).
  • 4.6 Pager Sound Alert On/Off [E-04]: Toggles pager sound alert (N: open, F: close, factory default: N).
  • 4.7 Pager Vibration Prompts On/Off [E-05]: Toggles pager vibration (N: open, F: close, factory default: N).
  • 4.8 Setting Pager Out-of-Bounds Prompt [E-06]: Sets the time after which an out-of-bounds alarm is triggered if no signal is received from the transmitter (value range: 01-30 minutes, 00 to turn off, factory default: 00).
  • 4.9 Setting Service Countdown Prompt Duration [E-07]: Sets the countdown time for service reminders (value range: 01-99 minutes, 00 to turn off, factory default: 00).
  • 4.10 Setting Group Calling [E-08]: Toggles group call function (N: open, F: close, factory default: N).
  • 4.11 Setting Transmitter User Password [E-09]: Sets the password for accessing the setup menu (initial password: 1234, manufacturer's super password: 2580).
  • 4.12 Setting Countdown Prompt Time [E-10]: Sets the countdown time for pagers (value range: 00-99 minutes, 00 to turn off, factory default: 00).
  • 4.13 Timing and Countdown Display Mode [E11]: Configures how timing and countdown are displayed on the pager (U.F.d.F: no timing, U.N.d.F: positive timing, U.F.d.N: countdown display).
  • 4.14 Prompting Mode (Sound/Light/Vibration) Switch when Timing Countdown is Completed [E12]: Sets the prompting mode (sound/light/vibration) when the countdown is complete (factory default: F.F.F - all off).
  • 4.15 Transmitter Prompt Sound On/Off [E-13]: Toggles transmitter sound (N: open, F: close, factory default: N).
  • 4.16 Transmitter Vibration On/Off [E-14]: Toggles transmitter vibration (N: open, F: close, factory default: N).

5.2. Calling the Pager

Input the pager number on the transmitter and press the [CALL] button to call the pager. Use the up or down arrow to increase or decrease the number.

5.3. Stop Pager Tip

To stop a pager alert, place the pager back onto the charging base (with power on) or touch the mute button on the side of the pager. The mute button function can only be triggered 3 seconds after the call to prevent accidental activation.

Note: In case of a countdown timer or service countdown prompt, the pager must be put back on the charging base to stop.

5.4. Powering Off/On the Pager

When an off-power pager is placed on the charging base in the power-on state, the pager will be turned on directly. If the pager is already in the charging base, it can be turned on/off by pressing the [Power] button on the transmitter, and the corresponding keyboard will enter the corresponding state at the same time.

Note: The transmitter can only be used to control the power on/off of the pager after the code is matched between the pager and the transmitter, and the charging base ID is already set up.

5.5. F1 (Modify Charging Base ID Synchronization Setting Parameter) Function

Confirm that the transmitter's E-00 to E-14 menu parameters have been set. Enter the ID number (1-999) in the standby interface, press the base button (diagram 3.1, item 4) to enter the setup state (press again to exit or automatically exit after 10s), then press the "F1" button and listen for a long beep from the base buzzer. This indicates the charging base ID setting is complete.

Note: The ID number of the charging base is related to the starting number of the pager when you change the code by one-key change function. If there are more than one base, it is recommended to set the base ID numbers in order (e.g., 1, 2, 3, etc.).

5.6. F2 (One-key Code Change) Function

Confirm that the "F1" function has been set. Enter the starting number (1-999), click "F2". The base will begin to write the pager numbers in turn. Wait for the base to sound a long beep and for all pagers to return to the charging state (number setup is complete).

Note: Pager number = ((base ID -1)*10)*step length + start number + slot number*step length, where slot number is 0-9.

5.7. F3 (Group Call) Function

Confirm that the "F2" function has been set and the "E-08" function is "On". Then click "F3" to group call all pagers. Press "F3" again within 5 seconds to cancel the group call, and press again after 5 seconds to group call again.

5.8. F4 (Call Bracelet) Function

This function can call the TD112 bracelet. When the transmitter clicks "F4", the screen displays "P.-----". Enter the ID number of the bracelet (1-999) and click "CALL" to call the bracelet. (The bracelet can only be called after it is registered in this way in advance.)

Note: Click "F4" again to exit the call bracelet function, the screen displays "-----".

TD112 Bracelet Operation:

  1. Set TD112 bracelet ID (serial number):
    • Under standby state, long press [A] key to enter setting menu, press [A] key twice to select "Name and ID".
    • Long press [A] key to enter, touch [B] key to shift to select number of digits, touch [A] key to switch digital/alphabetical cycle.
    • Long press [B] key twice to exit and return to standby mode.
  2. Register the transmitter ID to the TD112 bracelet:
    • Under standby state, long press [A] key to enter setting menu, touch [A] key again to enter code pairing mode, select (extension code pairing/transmitter host code pairing).
    • Touch [A]/[B] key, switch to "Transmitter Host Code", long press [A] key to enter code pairing mode. The interface displays bracelet ID, keypad serial number (01-50), and keypad ID ("FFFF" means not registered). Long press [A] key to delete current paired keyboard ID.
    • Long press [A] key to enter, touch [A]/[B] key to turn up and down to desired keyboard ID (01-50). After transmitter inputs current ID of bracelet, press [CALL]. Transmitter ID will be copied to bracelet, bracelet will vibrate and display OK.
    • Long press [B] key twice to exit, TD112 bracelet returns to standby mode.
    • Transmitter inputs bracelet ID and clicks "CALL" to call registered bracelet.

5.9. Using the Upper Computer (PC Software)

This product supports connection and operation via a computer. The upper computer control software can be downloaded from: https://www.retekess.com/resources/download.

5.9.1. Connecting Transmitter Host

To connect the transmitter to your computer:

  1. Refresh the COM port list.
  2. Select the correct COM port.
  3. Click 'Connect' to enter the main interface. Configuration information will be sent automatically.
  4. Select your preferred language.

Note: If the correct COM port does not appear, refresh the COM port first. If it still doesn't appear, check if the USB cable is connected correctly and if the driver is installed correctly on the computer.

5.9.2. Password Verification Screen

Setting password for the first time:

  1. Click 'Connect', the password setting window will pop up.
  2. Enter your desired password.
  3. Enter the password again for confirmation (both entries must match).
  4. Click 'OK' to successfully set up and open the main interface.

Entering Login Password: If a password has already been set, the Enter Password Verification screen is displayed after connection.

Modify Login Password: In the input password interface, enter the correct password and click 'Change Password' to open the password change interface.

5.9.3. Main Interface Introduction

The main interface provides various controls and displays:

  • Language selection
  • Device status (online: green background; offline: red background)
  • Pager number input box (1-999)
  • Call the entered pager number
  • Group call all pagers
  • Cancel group call
  • Base ID input box
  • Set the base ID (requires pressing the base ID setting button first)
  • One-key code change actual number
  • One-key code change command
  • Bracelet number input box
  • Call the input bracelet number
  • Cancel call bracelet
  • Panel and transmitter turn on
  • Shutdown of food tray and transmitter
  • Setting interface

5.9.4. Transmitter Setting Interface

This interface allows detailed configuration of the transmitter functions:

  • Group call function switch
  • Out-of-bounds countdown setting
  • Service countdown setting
  • Number step amplitude setting
  • Transmitter system ID modification
  • Set user password of transmitter
  • Transmitter beep switch setting
  • Setting vibration switch of transmitter
  • Setting the display mode of countdown timer
  • Flashing light prompt switch when timer countdown is completed
  • Sound prompt switch when timer countdown is finished
  • Vibrating prompt switch when timer countdown of the pager is completed
  • Setting the time for reminding the timer countdown of the diner
  • Light prompt switch for pager call
  • Diner call sound prompt switch
  • Vibrating alert switch for diner call
  • Diner call prompt time
  • Apply current settings to the transmitter host (if parameters are changed, base ID and pager number need to be reset)
  • Return to the host

6. Maintenance

6.1. Battery Safety

WARNING: KEEP NEW OR OLD USED BATTERIES OUT OF REACH OF CHILDREN.

  • In the event of a battery leaking, do not allow the liquid to come into contact with the skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek medical advice immediately.
  • If a radio or a battery has been submerged in water, please dry and clean it before use. Do not dry the radio or battery with an appliance or heat source, such as a hair dryer or microwave oven. If the radio has been submersed in a corrosive substance (e.g. saltwater), rinse the radio and battery in fresh water, then dry them.
  • Since batteries are sensitive to high temperatures when storing them, keep them in a cool and dry place. The recommended temperature should be between +10 °C and +25 °C and never exceed +30 °C. Batteries should therefore not be stored next to radiators or boilers nor in direct sunlight. Extremes of humidity (below 35% and above 95% relative humidity for sustained periods should be avoided since they are detrimental to both batteries and packing. Although the storage life of batteries at room temperature is good, storage is improved at lower temperatures provided special precautions are taken. Also, accelerated warming is harmful.
  • Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.
  • A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.
  • Turn off your radio before removing or installing a battery. Store spare batteries securely. Dispose of used batteries immediately and safely.
  • The battery supply terminals are not to be short-circuit.
  • Do not replace the battery in any area labeled "Hazardous Atmosphere". Any sparks created in a potentially explosive atmosphere can cause explosion or fire.
  • When the conductive material such as jewelry, keys or chains touches exposed terminals of the batteries, may complete an electrical circuit (short circuit the battery) and become hot to cause bodily injury such as burns. Exercise care in handling any battery, particularly when placing it inside a pocket, purse or other container with metal objects.
  • Dirty battery contacts need to be wiped with clean dry cloth, both on the battery and in the appliance.
  • Batteries should be removed from the appliance when not being used for long periods of time (months). The batteries should be enclosed in special protective packaging (such as sealed plastic bags or variants) which should be retained to protect them from condensation during the time they are warming to ambient temperature.
  • Exhausted batteries are to be removed from the equipment.
  • Do not dismantle, open or shred batteries. Batteries should be dismantled only by trained people.
  • Disposal of a battery into fire, or a hot oven, or mechanically crushing or cutting of a battery, that can result in explosion.
  • Turn off your radio before charging.
  • Batteries shall be charged at 10 °C ~ 40 °C environment temperature specified. If the environment temperature is lower than 0 °C, the charge shall be prohibited.
  • Rechargeable batteries need to be charged with a dedicated charger provided for each piece of equipment before you first use them.
  • Rechargeable batteries are only to be charged by adults or by children at least 8 years old under adult supervision.
  • Pull by the plug rather than the cord when disconnecting the charger.
  • Unplug the charger from the AC outlet before attempting any maintenance or cleaning.
  • Do not use the charger outdoors or in moist environments, use only in dry locations/conditions.
  • Do not disassemble the charger, which may result in a risk of electrical shock or fire. A charger should be dismantled only by trained people.
  • Do not operate the charger if it has been broken or damaged in any way.
  • An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in a risk of a fire and/or electric shock. If an extension cord must be used, make sure that:
    • The pins on the plug of the extension cord are the same number, size and shape as those on the plug of the charger.
    • The extension cord is properly wired and in good condition.
    • Make sure the cord is located so it will not be stepped on, tripped over or subjected to damage or stress.

6.2. Adapter

The plug of the adapter is considered a disconnect device. The socket-outlet shall be installed near the equipment and shall be easily accessible.

6.3. Carry Devices

For a list of Retekess-approved accessories for your radio model, visit the website http://www.retekess.com.

7. Troubleshooting

If you encounter issues with your TD177 system, please refer to the following common problems and solutions:

  • Pager not responding: Check if the pager is within range, fully charged, and if the transmitter ID and pager numbers are correctly synchronized.
  • Transmitter displays "Lo": The transmitter battery is low. Replace AAA batteries or connect to DC power.
  • False trigger alarm for out-of-bounds prompt: Ensure the transmitter has stable power and is not in a signal-shielded area.
  • Keys not working on transmitter: Avoid touching the keypad during power-up self-test (approx. 6 seconds). Do not press keys for more than 20 seconds during normal use, as this triggers an automatic touch baseline data update.
  • Interference: Refer to the FCC/IC compliance section for steps to mitigate electromagnetic interference.

8. Specifications

Component Specification
Transmitter
Frequency 433.92MHz
LCD 4 digital tube display
Modulation method ASK
Transmission power 360mW
Working distance 500 meters (open air)
Button capacitive touch 4*5
Input power DC 12V/1A Or AAA battery*3
USB interface connect to USB-A (female)
Product size 136mm*90mm*35mm
Pager
Frequency 433.92MHz
LCD 4 digital tube display
Prompting mode vibrate, beep, flashing
Standby time about 20 hours
Battery Built-in 300mAh lithium battery
Remind time 0-99s user-defined
Receiving sensitivity -113dBm
Waterproof grade IP67 waterproof and dustproof
Touch keys One mute key
Product size 52mm*100mm*15mm
Charging Base
Charging slots 10
Expansion 3 connections
Bracket hardware base bracket (optional)
Input power DC 12V/2A
Product size 167*120*190mm
RETEKESS TD177 Specifications Table
Figure 8: Detailed Specifications for Transmitter, Pager, and Charging Base

9. User Tips

  • For optimal range, ensure the transmitter antenna is positioned vertically and away from other electronic devices or power cords.
  • Regularly check pager battery levels to avoid service interruptions.
  • Utilize the group call function (F3) for busy periods to alert multiple guests simultaneously.
  • Customize pager stickers with your logo for a professional touch.
  • When setting up multiple charging bases, assign sequential IDs for easier management.

10. Frequently Asked Questions (FAQ)

Q: How do I change the pager numbers?
A: Use the F2 (One-key Code Change) function after setting the F1 function and desired step length (E-02).
Q: What should I do if a pager goes out of range?
A: The system has an out-of-range alarm (E-06). If triggered, the pager must be returned to the charging base to cancel the prompt.
Q: Can I use the system in a humid environment?
A: Yes, the pagers are IP67 waterproof and dustproof, making them suitable for kitchen or humid environments.
Q: How many charging bases can be cascaded?
A: The charging base supports cascading up to a maximum of 3 bases.

11. Warranty and Support

Most new products carry a two-year manufacturer's warranty from the date of purchase. For further details, please refer to the official Retekess after-sales service page: http://www.retevis.com/after-sale/.

For warranty service, you will need to provide a receipt or proof of purchase from the actual seller for verification.

11.1. Exclusions from Warranty Coverage:

  • Damage to any product caused by accident.
  • Damage resulting from misuse or abuse of the product, or unauthorized alterations or repairs.
  • If the serial number has been altered, defaced, or removed.

For assistance regarding repairs and service, please contact Retekess directly. For a list of Retekess-approved accessories for your radio model, visit the website http://www.retekess.com.

A user manual (PDF) is also available for download: TD177 User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.