Heltecbms 5A Capacitive Active Balancer

Contents

Heltec 5A Capacitive Active Balancer User Manual

Brand: Heltecbms | Model: 5A Capacitive Active Balancer

1. Introduction

This product is suitable for ternary lithium, lithium iron phosphate, and lithium titanate batteries. The active balancer is tailor-made for charging and discharging large-capacity series-parallel battery packs. Different from inductive balancer, capacitive balancer can achieve whole group balance. It doesn't need voltage difference between adjacent batteries to start balancing. It can effectively protect the circuit and improve the safety and reliability of your battery pack.

Various Heltec 5A Capacitive Active Balancers with wiring harnesses
Figure 1: Heltec 5A Capacitive Active Balancers with wiring.
Close-up of a Heltec 5A Capacitive Active Balancer with connected wires
Figure 2: Close-up of a single balancer unit.

2. Safety Precautions

  • Before connecting the balancer to battery or removing it, make sure that the wiring sequence is correct. Reverse or wrong connection will damage the balancer and battery, so be careful. We will not be responsible for serious consequences due to wiring errors.
  • Ensure insulation protection, heat dissipation as well as anti-static protection during use. When testing, installing, and touching the balancer, there must be corresponding protective measures.
  • Be careful not to touch the components on the circuit board with lead wires, electric soldering iron, tin slag, etc., otherwise the balancer may be damaged.
  • When connecting to the battery pack, the balancer needs to be placed on the surface of the insulating material outside the battery pack. Do not place it directly on the battery for balancing.
  • During use, you must follow the design parameters and usage conditions, and do not use it contrary to the parameters in this specification, otherwise it will easily damage the balancing board, and then damage the battery pack.
  • If any abnormality occurs during use, please stop using it immediately and return it to us or ask professional maintenance personnel for repair.

3. Product Overview

3.1. Features

  • Whole group balance: It has full indiscriminate balancing of the entire pack, automatic low-voltage sleep, and temperature protection.
  • High Quality: The circuit board is sprayed with three-proof paint, which has excellent insulation, moisture-proof, leakage-proof, shock-proof, dust-proof, anti-corrosion, anti-aging, corona resistance and other properties.
  • Safe and fast heat dissipation: The circuit board is equipped with an aluminum heat sink, which has the characteristics of fast heat dissipation and low temperature rise when working with high current.
  • Capacitive energy transfer: The maximum equalizing voltage difference is 0.01V and the maximum equalizing current is 5.5A.

3.2. Wide Applications

The Heltec 5A Capacitive Active Balancer is suitable for a variety of applications, including:

  • Electric Motorcycle
  • Electric Two-Wheeler
  • Electric Fork-lift
  • Electric Tour Car
  • Electric Golf Cart
  • Electric RV
  • Solar System
  • Electric Scooter

3.3. Basic Principle & Parameters

The maximum equalizing voltage difference is 0.01V. When the voltage difference is 0.1V, the current is about 0.5A (actually related to the capacity and internal resistance of the battery). When the battery is lower than 2.7V (ternary lithium/lithium iron phosphate), it stops working and enters sleep, with over-discharge protection function. The standby power consumption is less than 0.1mA.

The bigger the differential voltage, the bigger the equalization current; and the more balanced the battery, the smaller the working current. This active balancer can reach the maximum equalizing current of 5.5A and the balance voltage accuracy is within 5mV. It will stop working automatically when the voltage is lower than 3.0V for NCM/LFP battery, and 1.8V for LTO battery.

4. Specifications

Table 1: Main Technical Indicators

Technical Index Product Model (SKU by default)
0855A 1004A 0877A 1400 0999A16 1323
Battery Strings 3S-4S 4S-6S 6S-8S 9S-14S 12S-16S 17S-21S
Battery Type NCM/LFP/LTO
Working Voltage Range NCM/LFP: 2.7V-4.2V
LTO: 1.8V-3.0V
Voltage Balancing Accuracy 5mV (typical)
Balance Mode The whole group of battery participate in the active equalization of energy transfer at the same time
Balancing Current 0.08V differential voltage generates 1A balance current. The maximum allowable balance current is 5.5A.
Static Working Current 13mA 8mA 8mA 15mA 17mA 16mA
Working Temp -10°C~60°C
External Power No need for external power supply, it relies on the internal energy transfer of the battery to achieve the whole group balance.

5. Model Variations

Table 2: SKU Number Definition of Customized Versions

SKU Definition
0885A Standard version.
0855C For LTO battery only. (not for NCM/LFP)
0855D Stop balancing when cell 1 (the first cell of the first string) is 3.3V; and when it reaches 3.456V, re-start balancing.
0855PH2 PH2.0 connector instead of RUN point, balancer not in work by default. Wires can be connected to a switch or any BMS, so you can control the on and off of this balancer.

Example: If you have 4S LFP cells and want to control the balancer's on/off state, you can choose the 0855PH2 balancer. Connect the additional red wire to a switch or solder it to your BMS to enable control.

6. Accessories

The Heltec 5A Capacitive Active Balancer typically includes:

  • Heltec 5A Active Balancer (1 set, balancer board and wires)
  • Anti-static bag, anti-static sponge, and corrugated case

Optional accessories (for 4S version only):

  • TFT-LCD Display (with voltage collection function)
  • Acrylic Protective Case
  • ABS Shell

The TFT-LCD Display connects directly to the battery and can be used in parallel with any balancer or protection board. It displays the voltage of each string and the total voltage. Typical accuracy is ±5mV at room temperature (around 25°C) and ±8mV in the wide temperature range (-20°C to 60°C).

7. Installation and Assembly

7.1. Wiring Sequence

It is crucial to ensure the correct wiring sequence. Incorrect connection can damage the balancer and battery. Always connect the wires in the specified order, typically from the negative terminal (B-) to the positive terminals (B1+, B2+, ..., Bn+).

7.2. Physical Placement

When connecting to the battery pack, the balancer needs to be placed on the surface of an insulating material outside the battery pack. Do not place it directly on the battery for balancing to prevent potential short circuits or heat transfer issues.

7.3. Connector Definition

Connector Name Definition
A RUN The default is shorted, and an external switch can be connected to control the balance function. (Customized versions with PH2.0 connector are available for external control).
B- ~ Bn+ B- The negative pole of the 1st string (total)
B1+ The positive pole of the 1st string
B2+ The positive pole of the 2nd string
B3+ The positive pole of the 3rd string
B4+ The positive pole of the 4th string
B5+ The positive pole of the 5th string
...
Bn+ The positive pole of the nth string (final)
C LTO/ (from left to right)

7.4. Mode Selection (LTO/NCM/LFP)

The circuit solder joints for mode selection (RUN) are strictly prohibited from being soldered together with RUN. This will cause a short circuit and damage the balancer.

  • 1+2 pad short: For LTO (lithium titanate) battery.
  • 2+3 pad short: For NCM and LFP (ternary lithium/lithium iron phosphate) battery.

The RUN indicator light indicates the continuous working state of the balance, and it will only go out when the battery under-voltage protection or the balancer fails.

7.5. Wiring Diagrams

Detailed wiring diagrams for various battery string configurations (3S-21S) are essential for correct installation. These diagrams illustrate the precise connection points for each cell in your battery pack to the balancer. Please refer to the official PDF user manual for comprehensive and detailed wiring diagrams. The PDF manual can be found at: Heltec 5A Capacitive Active Balancer User Manual (PDF).

8. Operating Instructions

The Heltec 5A Capacitive Active Balancer operates automatically once correctly installed and connected to the battery pack. It continuously monitors the voltage of each cell and initiates balancing when voltage differences are detected.

  • Automatic Balancing: The balancer will automatically start equalizing energy transfer between cells to minimize voltage differences.
  • Low-Voltage Sleep: The balancer will stop working and enter a sleep state if the battery voltage drops below 2.7V (for NCM/LFP) or 1.8V (for LTO) to protect against over-discharge.
  • Indicator Light: The RUN indicator light signifies active balancing. It will turn off if the battery enters under-voltage protection or if the balancer fails.
  • Customized Control (0855PH2 model): For models like 0855PH2, the balancer is not active by default. You can connect an external switch to the PH2.0 connector to manually turn the balancing function on or off.
Video 1: Demonstration of the Heltec Active Balancer in operation, showing voltage equalization across battery cells on a voltage tester.

9. Maintenance

  • Regular Inspection: Periodically check all wiring connections to ensure they are secure and free from corrosion or damage.
  • Cleanliness: Keep the balancer board clean and free from dust and debris. Use a soft, dry cloth for cleaning.
  • Environmental Conditions: Ensure the balancer operates within its specified working temperature range (-10°C to 60°C) and avoid exposure to excessive moisture or extreme temperatures.
  • Heat Dissipation: Verify that the aluminum heat sink is not obstructed and allows for proper airflow to maintain optimal operating temperatures.
  • Avoid Physical Damage: Handle the balancer with care to prevent physical impact or damage to the circuit board components.

10. Troubleshooting

  • Balancer Not Activating: Check all wiring connections for correctness. Ensure the battery voltage is within the operating range. For 0855PH2 models, verify the external switch is in the 'ON' position.
  • RUN Indicator Off: This indicates either under-voltage protection is active (battery voltage too low) or a balancer fault. Check battery voltage first.
  • Persistent Voltage Imbalance: If significant voltage differences persist after an extended period, re-check wiring and ensure the balancer is correctly configured for your battery type (LTO/NCM/LFP). Large capacity battery packs may require longer balancing times.
  • Physical Damage: If any components appear burnt or damaged, discontinue use immediately.

For complex issues or if the problem persists, please contact professional maintenance personnel or Heltec support.

11. User Tips

  • For optimal performance, ensure your battery pack is initially as balanced as possible before installing the active balancer.
  • Consider exploring different versions of the balancer (e.g., 0855PH2) if you require external control over the balancing function for specific applications.
  • Patience is key: Larger battery capacities will naturally take longer to achieve full balance. Monitor the voltage differences over time.

12. Frequently Asked Questions (FAQ)

Q: Does this balancer require an external power supply?
A: No, the Heltec 5A Capacitive Active Balancer operates by transferring energy directly from the battery cells, requiring no external power supply.
Q: How accurate is the voltage balancing?
A: The balancer achieves a voltage balancing accuracy of 5mV (typical) at room temperature.
Q: Can I use this balancer with different battery types?
A: Yes, it is compatible with NCM (Ternary Lithium), LFP (Lithium Iron Phosphate), and LTO (Lithium Titanate) batteries. Ensure the correct mode is selected via solder pads if applicable.

13. Warranty and Support

13.1. Warranty Terms

Thank you for purchasing the Heltec 5A Capacitive Balancer for Lithium Battery launched by Chengdu Heltec Energy Technology Co., Ltd. We provide quality warranty for the hardware products and accessories sold by the company.

  • Warranty Period: One Year.
  • If a malfunction occurs due to quality reasons during the warranty period, the company has the right to choose to repair or replace the entire product after receiving notification of the product malfunction and verification. The entire set of replacement products may be new or nearly new.
  • Chengdu Heltec Energy Technology Co., Ltd. guarantees that the products have been fully tested.
  • The product warranty period starts from the date of shipment or the date of installation by Chengdu Heltec Energy Technology Co., Ltd. If installation does not begin within 30 days after shipment, the warranty period begins on the 31st day after shipment.

Exclusions: Chengdu Heltec Energy Technology Co., Ltd. does not provide free warranty for product failure and damage caused by any of the following conditions:

  • Incorrect use or improper maintenance;
  • Software, accessories, components or other items not provided by Chengdu Heltec Energy Technology Co., Ltd.;
  • Unauthorized disassembly, modification and misuse;
  • Use beyond the scope specified in the product technical specifications;
  • Improper transportation, handling and storage;
  • Failure or damage caused by other non-quality reasons (such as earthquakes, wars, traffic accidents, etc.)

To the extent permitted by law, the above warranty terms are express and exclusive and there are no other warranties of any kind, whether written or oral. Any implied warranties and commercial terms are expressly disclaimed.

13.2. Contact Information

  • Company: Chengdu Heltec Energy Technology Co., Ltd
  • Address: No. 16th Chenghong Road, Chenghua 610051, Chengdu, Sichuan, China.
  • Website: www.heltec-energy.com
  • Email: jacqueline@heltec-bms.com
  • Tel: 0086-028-83267289

© 2023 Heltecbms. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.