Hti HT-18/HT-175/HT-02

Contents

Hti Infrared Thermal Imaging Camera User Manual

Models: HT-18, HT-175, HT-02

1. Introduction

This manual provides detailed instructions for the safe and effective use of your Hti Infrared Thermal Imaging Camera. These devices are designed for various applications including building inspection, electrical inspection, auto repair, floor heating detection, and general fault detection in industrial and domestic settings. Please read this manual thoroughly before operating the device.

Various applications of the thermal imaging camera including building inspection, electrical inspection, and auto repair.
Figure 1: Product Application Examples

2. Safety Information

Always observe the following safety precautions to prevent injury or damage to the device:

  • Do not point the camera directly at strong light sources (e.g., sun, lasers) as this may damage the sensor.
  • Keep the device dry and away from extreme temperatures.
  • Use only the specified battery types and charging methods.
  • Do not attempt to disassemble or modify the device.
  • Ensure the device is stored within the recommended temperature and humidity ranges.

3. Setup

3.1 Package Contents

Verify that all items are present in your package:

  • Infrared Thermal Imaging Camera (HT-18, HT-175, or HT-02 model)
  • USB Cable
  • User Manual
  • Carry Pouch
  • Carry Pouch Strap (for HT-18)
  • Cardboard Package Box
  • 18650 Battery (for HT-18) or AAA Alkaline Batteries (for HT-175, HT-02)
HT-18 Thermal Imaging Camera with its packaging, user manual, USB cable, charger, and carry pouch.
Figure 2: HT-18 Package Contents
HT-02 Thermal Imaging Camera with its packaging, user manual, and batteries.
Figure 3: HT-02 Package Contents

3.2 Battery Installation and Charging

For HT-18: This model uses a built-in rechargeable 18650 battery.

  1. Locate the battery compartment on the handle.
  2. Insert the 18650 battery, ensuring correct polarity.
  3. Close the battery compartment cover.
  4. To charge, connect the camera to a power source using the provided Micro USB 2.0 cable. The battery indicator on the screen will show charging status.

For HT-175 and HT-02: These models use AAA alkaline batteries.

  1. Locate the battery compartment on the handle.
  2. Insert the required number of AAA alkaline batteries, ensuring correct polarity.
  3. Close the battery compartment cover.
Video 1: Demonstrates battery installation and charging for the HT-18 model.

4. Operating Instructions

4.1 Power On/Off

To power on or off the device, hold down the power button (usually marked with a “⑂” symbol) until the screen activates or deactivates.

4.2 Basic Operation

Once powered on, the camera will display a thermal image. Point the camera at the object or area you wish to inspect. The screen will show the temperature distribution in various colors, with a crosshair indicating the measurement point.

Thermal camera displaying a thermal image of an electrical panel, showing hot spots.
Figure 4: Thermal camera in use on an electrical panel
Thermal camera displaying a thermal image of a car engine, highlighting temperature variations.
Figure 5: Thermal camera in use on a car engine

4.3 Menu Navigation and Settings

Use the navigation buttons (MENU, SELECT, ENTER, and arrow keys) to access and adjust settings.

  • Images: View captured images.
  • Color Palette: Select from five types of color palettes (Spectra, Iron, Cool, White, Black) to better visualize temperature differences.
  • Emissivity: Adjust the emissivity value (0.1 to 10.0) based on the material being measured for accurate readings.
  • Settings: Access general settings such as language, date/time, and auto power-off duration.
Thermal camera screen showing a menu with language options like English, Chinese, Italian, and German.
Figure 6: Language Selection Menu

5. Maintenance

5.1 Cleaning

To clean the device, use a soft, dry cloth. Do not use abrasive cleaners or solvents. For the lens, use a lens cleaning cloth and solution designed for optics.

5.2 Battery Care

  • For rechargeable batteries (HT-18), ensure regular charging and avoid complete discharge for prolonged battery life.
  • For models using AAA batteries (HT-175, HT-02), remove batteries if the device will not be used for an extended period to prevent leakage.

5.3 Storage

Store the thermal imaging camera in its provided carry pouch in a cool, dry place. Recommended storage temperature is -40°C to 80°C (-4°F to 176°F) for HT-18, -20°C to 50°C (-4°F to 122°F) for HT-175 and HT-02, with relative humidity below 85%RH.

6. Troubleshooting

If you encounter issues with your thermal imaging camera, refer to the following common problems and solutions:

  • Device does not power on: Check battery charge level. For HT-18, ensure the 18650 battery is properly inserted and charged. For HT-175/HT-02, ensure AAA batteries are correctly installed and not depleted.
  • Image is unclear or inaccurate:
    • Verify that the lens cover is removed.
    • Ensure the emissivity setting is appropriate for the material being measured.
    • Check for any obstructions or dirt on the lens.
  • Cannot save images: Ensure the internal 4GB storage (HT-18) or Mini SD card (HT-02) has sufficient free space.
  • Device powers off unexpectedly: Check the auto power-off settings in the menu and adjust if necessary.

For further assistance, please refer to the full user manual PDF or contact customer support.

7. Specifications

FeatureHT-18HT-175HT-02
Display Screen3.2" Full-color2.0" Color2.4" Wide Viewing Angle Color LCD
Infrared Image Resolution220x16032x3260x60
Visible Image Resolution0.3 Million PixelN/A0.3 Million Pixel
Thermal Sensitivity0.07°CN/A0.15°C
Temperature Measurement Range-20~300°C (-4~572°F)-20~300°C (-4~572°F)-20~300°C (-4~572°F)
Measurement Precision±2.5°C or ±2.5%±2% / ±2°C±2% or ±2°C (±4°F)
Wavelength Coverage8-14um8-11.5um8-14um
Focus ModeFixedFixedFixed
Image Capture Frequency8HzN/A6Hz
Storage MediumBuilt-in 4GBN/AMini SD card (4G)
Image FormatJPGN/ABMP
Power SupplyBuilt-in 18650 rechargeable battery3x AAA alkaline battery4x AAA alkaline battery
USB InterfaceMicro USB2.0N/AN/A
Auto Power-off Time5/20 minutes (adjustable)N/A12 minutes
Dimensions (L×W×H)90×105×223mm165×58×64mm21.2×9.5×6.2cm
Weight289gN/A320g
Operating Temperature0°C to 50°C0°C to 50°C-5°C to 40°C (23°F to 104°F)
Storage Temperature-40°C to 80°C-20°C to 50°C-20°C to 50°C (-4°F to 122°F)
Humidity<85%RHN/A10%RH to 80%RH
CertificationCE, FCC, RoHSN/ACE (EN61326-1:2006)

8. User Tips

  • For best results, ensure the emissivity setting matches the material you are inspecting. Different materials reflect and emit infrared radiation differently.
  • Experiment with different color palettes to find the one that best highlights the temperature variations for your specific application.
  • Regularly check the battery level, especially before critical inspections, to avoid interruptions.
  • Keep the lens clean to ensure clear and accurate thermal images.

9. Warranty and Support

The HT-02 model comes with a 2-year warranty period. For other models, please refer to your purchase documentation for specific warranty details.

For detailed instructions, diagrams, and further support, please refer to the official user manual PDF available at: User Manual (PDF).

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.