1. Product Information
Product Name: SOLDERING TIP
Model: C245/C210/CLL5/ET/LT/900/T12 series
Batch Number: 1155998324#
The Weller ET Series soldering tips are designed for precision soldering tasks, offering various shapes and sizes to suit different applications. These tips are compatible with Weller WES50, WES51 soldering stations and PES51, LR21 50W soldering guns.


2. Safety & Warnings
Read all instructions before use to ensure safety and prevent damage.
- Warning: Keep the device and its cord out of reach of children under 3 years old.
- Soldering Safety: Always wear protective eyewear when soldering. Ensure good ventilation in the work area to prevent inhalation of flux fumes.
- Usage Environment: The soldering station must be properly grounded to prevent static electricity damage to sensitive components.
3. Specifications
These soldering tips are made of oxygen-free high-conductivity copper and are iron plated for durability and resistance to solder erosion. They feature nickel plating for corrosion protection, chrome plating for unwetted surfaces, and are tinned for proper wetting and efficient heat transfer.


Dimensions:


Specific Tip Dimensions:




4. Setup and Preheating
- Connect: Connect the soldering iron to the soldering station.
- Power On: Turn on the power of the soldering station.
- Set Temperature: Set the temperature between 300°C and 380°C.
- For leaded solder: 330-370°C
- For lead-free solder: 350-400°C or higher
- Clean and Tin (Initial): Before use, clean the tip on a damp sponge or metal scouring pad. Apply fresh solder to the tip to create a thin layer of tin. This process, known as "tinning" or "soldering," prevents oxidation and improves heat conduction.
5. Operating Instructions
Soldering Operation:
- Simultaneously contact the soldering iron tip with both the component lead and the PCB pad.
- Heat for approximately 1-2 seconds.
- Feed in the solder wire.
- Once the solder melts and wets the pad, remove the solder wire.
- Finally, remove the soldering iron tip to allow the solder joint to cool naturally.
6. Maintenance and Care
Daily Maintenance:
- Preventing Oxidation: Do not dry-heat the soldering iron tip for extended periods at excessively high temperatures, as high temperatures will accelerate oxidation.
- Cleaning Method: Never use files or sandpaper to mechanically clean the soldering tip. Use a dedicated damp sponge or brass wool.
- Removing Oxidation: If the soldering iron tip is oxidized and blackened, preventing it from accepting solder, it can be repaired using a special "soldering iron tip revival paste."
- Consumable Replacement: The soldering iron tip is a consumable. Replace it promptly when surface wear or structural changes cause it to lose solderability.
General Maintenance & Storage:
- Cleaning: Turn off the device before cleaning. Use a soft, lint-free cloth.
- Storage: Store in a dry place at room temperature (15°C - 35°C).
- Long-term Storage: If not used for a long time, keep the soldering iron tip tinned and put the soldering station into sleep mode.
7. Troubleshooting
- Tip Not Accepting Solder (Oxidation): If the tip appears oxidized or blackened and solder does not adhere, use a soldering iron tip revival paste to clean and re-tin the tip. Ensure proper tinning after each use.
- Poor Heat Transfer: Ensure the tip is clean and properly tinned. Check that the soldering station is set to the correct temperature for the type of solder being used. Excessive oxidation can also hinder heat transfer.
- Tip Wear/Damage: Soldering tips are consumables. If the tip shows significant surface wear or structural changes that affect its performance, it should be replaced.
8. User Tips
- Tip Selection: Different soldering iron tip shapes are suitable for different tasks. For example, knife-edge tips are ideal for drag soldering, while pointed tips are best for small components. Consider purchasing a variety pack to cover diverse needs.
- Compatibility Check: Always verify that the chosen tip model (e.g., ETH, ETD) is compatible with your specific Weller soldering station (e.g., WES50, WES51) or soldering gun (e.g., PES51, LR21).
- Proper Tinning: Consistent and proper tinning of the tip is crucial for longevity and performance. Always re-tin the tip after use to protect it from oxidation.
9. Manufacturer & Support Information
Manufacturer: Shenzhen Handifeng Technology Co., Ltd.
Email: sales17@handif.com
EU Authorized Representative: VAT SPEED SL
Address: Calle Antonio Salvador N99.1, 28026 Madrid, Spain
Email: services@vatspeed-eu.com
10. Disposal & Recycling
This symbol indicates that this product should not be treated as household waste. According to the WEEE Directive (2012/19/EU), it must be disposed of at an appropriate electronic waste collection point for recycling to prevent potential negative consequences for the environment and human health.