SLMPLEFUN 2204+EV15274A RF Relay Receiver Module

Contents

SLMPLEFUN 433MHz Universal Wireless Remote Control Switch

Instruction Manual

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your SLMPLEFUN 433MHz Universal Wireless Remote Control Switch. This 4-channel RF relay receiver module is designed for versatile control of various AC and DC devices, including gate openers, garage doors, LED lights, and motors.

SLMPLEFUN 433MHz Universal Wireless Remote Control Switch showing receiver, remote, voltage, channels, distance, and RF 433

Figure 1: SLMPLEFUN 433MHz Universal Wireless Remote Control Switch components.

2. Safety Information

  • Ensure all power is disconnected before installation or wiring to prevent electric shock.
  • This device operates with AC 85V-250V. Handle with care.
  • Do not expose the device to moisture or extreme temperatures.
  • Only use the device for its intended purpose as described in this manual.
  • Professional installation is recommended for complex wiring scenarios.

3. Package Contents

Your package should include the following items:

  • 1 x 4-Channel RF Relay Receiver Module
  • 1 x Remote Control (CR2032 battery included)
Single remote control with CR2032 battery included

Figure 2: Remote control with included CR2032 battery.

4. Technical Specifications

FeatureSpecification
Working VoltageAC 85V~250V
Input/Output Voltage1V-250V
Output TypePassive output (Dry Contact)
Quiescent Current5mA
Max Current10A
Max Load2200W
RF Frequency433MHz
Pin ConfigurationNO / COM / NC
Working Temperature-30~+80 Celsius
Receiving Sensitivity97dbm
Max Remote Controls Stored25 pieces
Support Encoding1527 Learning code / 2262 fixed code
RF Operating ModeASK superheterodyne wireless reception
Receiving RangeOpen space more than 50 meters
Remote Operating ModeMomentary / Toggle / Latched / Mix Mode
Receiver Dimensions70*50*25mm
Remote Dimensions65*35*10mm
Remote BatteryCR2032 (included)

5. Product Overview

The receiver module features several key components for its operation:

  • NO (Normally Open Pin): Connects to the device when the relay is activated.
  • COM (Common Pin): The common connection point for the relay.
  • NC (Normally Closed Pin): Connects to the device when the relay is inactive.
  • Antenna: For receiving RF signals from the remote control.
  • Indicator Light: Provides visual feedback on the module's status.
  • Learning Button: Used for pairing remote controls and setting operating modes.
Receiver board with labeled pins: N, L, NC, COM, NO, Indicator light, Learn button, Antenna. Dimensions 70x50x25mm.

Figure 3: Receiver Module Component Layout.

6. Wiring Diagrams

Important: Ensure all power is disconnected before performing any wiring. Incorrect wiring can damage the device or cause electrical hazards. Signal pairing is required before use.

Four wiring diagrams for AC device, DC motor, DC device, and AC motor control using the relay module.

Figure 4: General Wiring Diagrams for various applications.

6.1. AC Device Wiring (e.g., Lights)

Connect the AC power supply (85V-250V) to the L and N terminals of the receiver. Connect your AC device (e.g., light bulb) to the COM and NO terminals of the desired relay channel. When the relay is activated, power will flow to the device.

Application example showing remote control activating lights connected to the AC device wiring configuration.

Figure 5: Example of AC device control (lights).

6.2. DC Motor Wiring (e.g., Linear Actuator)

For DC motors (12V, 24V, 36V, etc.), connect the DC power supply to the motor. The relay module acts as a switch for the motor's power lines. Connect the motor's positive and negative terminals to the COM and NO/NC terminals of two separate relay channels, allowing for forward and reverse control. The AC 85V-250V input powers the receiver module itself.

6.3. AC Motor Wiring (e.g., Blinds, Garage Door)

For AC motors (e.g., for blinds or garage doors), connect the AC power supply (85V-250V) to the L and N terminals of the receiver. Connect the motor's 'Up' and 'Down' control lines to the NO terminals of two separate relay channels, with the common line connected to the COM terminal. The 'E' terminal typically refers to the Earth/Ground connection for the motor.

Application example showing remote control activating an AC motor for blinds, with corresponding wiring diagram.

Figure 6: Example of AC motor control (blinds).

Video 1: Demonstration of wiring and operation for a DC motor (linear actuator) and a light bulb using the relay module and remote control.

7. Operating Modes

The receiver module supports several operating modes, which determine how the relays respond to remote control commands:

  • Momentary Mode: Press and hold button "A" on the remote, relay "1" turns ON. Release button "A", relay "1" turns OFF.
  • Toggle Mode: Press button "A" on the remote, relay "1" turns ON. Press button "A" again, relay "1" turns OFF.
  • Latched Mode: Press button "A" on the remote, relay "1" turns ON. Press button "B" on the remote, relay "2" turns ON, and simultaneously relay "1" turns OFF.
  • Mix Mode (4): Relays "1" and "2" operate in Momentary mode, while relays "3" and "4" operate in Toggle mode.
  • Mix Mode (5): Relays "1" and "2" operate in Momentary mode, while relays "3" and "4" operate in Latched mode.
  • Mix Mode (6): Relays "1" and "2" operate in Toggle mode, while relays "3" and "4" operate in Latched mode.

8. Setup and Pairing Remote Controls

To pair a remote control and set an operating mode, follow these steps:

  1. Select Mode: Press the learning button on the receiver module a specific number of times according to your desired mode:
    • Momentary Mode: Press 1 time.
    • Toggle Mode: Press 2 times.
    • Latched Mode: Press 3 times.
    • Mix Mode (4): Press 4 times.
    • Mix Mode (5): Press 5 times.
    • Mix Mode (6): Press 6 times.
  2. After pressing the learning button, wait for 3 seconds. The indicator light on the receiver will blink, indicating it's ready for pairing.
  3. Pair Remote: Press button "A" on your remote control. For Latched Mode, also press button "B".
  4. Wait for 3 seconds. The indicator light will stop blinking, confirming successful pairing.

Note: The remote control signal can pass through walls, offering flexible placement. The system also features free pairing and anti-interference capabilities.

Diagram showing remote control signal passing through walls and multiple remotes pairing with one receiver.

Figure 7: Signal penetration and multi-remote pairing capability.

9. Reset Procedure

To clear all paired remote controls and reset the receiver module to its default state:

  • Press the learning button on the receiver module 8 times.
  • The indicator light will flash, confirming that all stored remote controls have been cleared.

Important: After a reset, all previously paired remote controls will no longer function with this receiver until they are re-paired.

10. Application Examples

This versatile remote control switch is suitable for a wide variety of scenarios, enhancing convenience and automation in your home or workplace:

  • Home Automation: Control lighting, automated curtains, fans, and other household appliances.
  • Garage & Gate Control: Operate garage doors, sliding doors, courtyard gates, and barriers.
  • Industrial Use: Manage cranes, telescopic doors, and other machinery.
  • Specialized Applications: Stage lighting control, and various DIY projects requiring remote switching.
Illustrations of various applications including crane, telescopic door, stage lighting, lamp, sliding door, garage door, courtyard gate, and barrier.

Figure 8: Diverse application scenarios for the remote control switch.

11. User Tips

  • This product functions as a versatile switch, capable of handling a maximum current of 10A, making it suitable for various electrical loads.
  • It enhances convenience and efficiency by allowing remote control of home appliances and automation of different processes.
  • The product is categorized as universal due to its broad compatibility with various devices and applications.
  • Key features include RoHS certification, a wide operating temperature range (-30~+80 Celsius), low quiescent current (5mA), and good receiving sensitivity (97dbm).

12. Troubleshooting

  • Remote not responding: Check if the remote control battery (CR2032) needs replacement. Ensure the remote is within the 50-meter open-space range.
  • Device not activating: Verify all wiring connections are secure and correct according to the wiring diagrams. Ensure the receiver module is powered.
  • Remote control mode issues: If the remote is not operating in the desired mode, perform a reset (Section 9) and then re-pair the remote in the correct operating mode (Section 8).
  • Poor signal reception: Slightly stretch the antenna on the receiver for better signal reception. Ensure there are no major obstructions between the remote and the receiver.

13. Maintenance

  • Battery Replacement: The remote control uses a CR2032 lithium battery. Replace the battery in time when the remote control voltage is low to maintain strong signal transmission.
  • Cleaning: Use a dry, soft cloth to clean the receiver module and remote control. Do not use liquid cleaners.
  • Antenna: For optimal performance, ensure the receiver's antenna is not obstructed and is slightly stretched.

14. Warranty and Support

This product is manufactured by Huizhou Wenqiao Electronic Technology Co., Ltd. and holds CE and RoHS certifications, ensuring compliance with European safety and environmental standards.

For any questions or support, please contact the manufacturer:

  • WhatsApp: +86 181 3880 5271 / +86 135 0227 8583
  • Email: dieseelectronic@163.com

Certifications:

Certifications including CE, FC, UK CA, and RoHS logos.

Figure 9: Product Certifications.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.