TOMZN TOMPD-63S

Contents

TOMZN TOMPD-63S Automatic Reconnect Over Under Voltage Current Leakage Protector

User Instruction Manual

1. Safety Information

WARNING: To avoid danger of suffocation, keep any plastic packaging away from babies and children. Do not use this packaging in cribs, beds, carriages, or playpens. This packaging is not a toy.

Always ensure that installation and maintenance are performed by a qualified electrical professional to prevent electric shock or damage to the device and connected equipment.

2. Product Overview

The TOMZN TOMPD-63S is a multi-functional Din Rail mounted protector designed to safeguard electrical circuits and appliances from various power anomalies. It provides automatic reconnection after a fault, offering protection against over-voltage, under-voltage, over-current, and leakage current. The device also features a digital display for real-time monitoring of voltage, current, power, power factor, and energy consumption (KWH).

Front view of TOMZN TOMPD-63S protector with digital display
Figure 1: Front view of the TOMPD-63S protector showing the digital display and control buttons.

3. Specifications

FeatureSpecification
Model NumberTOMPD-63S
TypeVoltage Protector
Brand NameTOMZN
Rated Current1-63A Adjustable
Over Voltage RangeAC250~300V (adjustable)
Low Voltage RangeAC150~190V (adjustable)
EU LVD VoltageHigh voltage: Above 50Vac or 75Vdc
CertificationCE
Is Smart DeviceNo
OriginMainland China
FunctionsOver/Under Voltage Protection, Over Current Protection, Leakage Protection, Automatic Reconnect, KWH Meter

4. Setup and Installation

  1. Professional Installation: Upon receiving the product, it is imperative that an electrical professional performs the installation and initial operation.
  2. Mounting: The TOMPD-63S is designed for Din Rail mounting. Secure it firmly onto a standard 35mm Din Rail within an appropriate electrical enclosure.
  3. Wiring: Connect the equipment in accordance with local electrical codes and the specific wiring diagram provided with the device (if applicable). Ensure correct input (IN) and output (OUT) connections. Tighten all terminal screws securely to prevent loose connections and arcing.
  4. Power On: After wiring, apply power to the circuit. The device's digital display should illuminate.
Top and bottom view of the protector showing IN and OUT terminals
Figure 2: Top and bottom view illustrating the input (IN) and output (OUT) terminals for wiring.

5. Operating Instructions

5.1 Display Modes

The device features a digital display that cycles through various parameters or can be manually switched.

Display showing Power, PF Power Factor, and Energy KWH modes
Figure 3: The digital display can show Power (W), Power Factor (PF), and Energy Consumption (KWH).

5.2 Parameter Adjustment

The TOMPD-63S allows for adjustment of protection thresholds (over-voltage, under-voltage, over-current). Refer to the specific instructions provided with your device for detailed steps on how to enter the settings menu and modify these parameters using the front panel buttons.

Hand pressing the SET button on the protector
Figure 4: Interaction with the control buttons (Power, SET, Up, Down) for configuration.

Typically, the 'SET' button is used to enter the configuration mode, and the 'Up' and 'Down' arrows are used to navigate and adjust values. Press 'SET' again to confirm and exit.

5.3 Function Overview

When the voltage in the circuit exceeds the set over-voltage limit or drops below the set under-voltage limit, the equipment will automatically cut off the circuit to protect connected devices. Similarly, if the current exceeds the set limit or a leakage current is detected, the protector will trip. The device is designed for automatic reconnection once the fault condition is cleared and a pre-set delay has passed.

6. Maintenance

  • Placement: Do not place the device near flammable materials.
  • Ventilation: Ensure adequate ventilation around the device during operation to prevent overheating.
  • Cleaning: Keep the device clean and free from dust. Use a dry, soft cloth for cleaning. Do not use abrasive cleaners or solvents.
  • Storage: Disconnect the device from power and store it properly in a dry, cool place when not in use for extended periods.

7. Troubleshooting

  • Device Not Powering On: Check the input power supply. Ensure all wiring connections are secure and correct. If the issue persists, consult an electrician.
  • Frequent Tripping: Review the set over-voltage, under-voltage, over-current, and leakage current thresholds. These might be set too sensitively for your load or power conditions. Check for actual faults in the circuit or connected appliances.
  • Display Not Working: If the device is powered but the display is blank, try cycling the power. If it remains unresponsive, the unit may require professional inspection or replacement.
  • No Automatic Reconnection: Ensure the fault condition has genuinely cleared. Some faults may require manual reset or persist. Check the device's status indicators (if any) for specific fault codes.

8. User Tips

  • Adjustable Settings: Take advantage of the adjustable voltage and current limits to tailor the protection to your specific electrical system and connected loads.
  • Leakage Protection: This device includes leakage current protection, which is crucial for safety. Ensure it is properly configured and tested by a professional.
  • Monitor KWH: Use the KWH display mode to monitor energy consumption of the protected circuit, which can help in energy management.

9. Applicable Regulations and Harmonized Standards

This device conforms to the following directives:

  • Low Voltage Directive 2014/35/EU
  • Electromagnetic Compatibility Directive 2014/30/EU
  • Restriction of the Use of Certain Hazardous Substances (RoHS) Directive 2011/65/EU

10. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your point of purchase or the manufacturer directly. Keep your purchase receipt as proof of purchase.

© 2024 TOMZN. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.