CNSPEED 620 Series Gauge

Contents

CNSPEED 620 Series 60mm Car Gauge Instruction Manual

Model: 620 Series Gauge

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your CNSPEED 620 Series 60mm car gauge. These professional-grade gauges are designed for 12-volt automotive systems and are suitable for various applications, including monitoring boost, temperatures, pressures, voltage, and RPM. Please read this manual thoroughly before installation and use to ensure proper function and safety.

For additional detailed guides and documents, please refer to the official user manual PDF: User Manual (PDF).

Specifications

FeatureDetail
Brand NameCNSPEED
PowerDC 12V Professional
Diameter2.5 inches / 60mm
MaterialABS + METAL
Item Weight0.6kg
Item Length20cm
Item Width15cm
Item Height12cm
Placement on VehicleFront
Special FeaturesAll Car gauge
Interchange Part NumberYC101246
Manufacturer Part Number1410+0211/1172-1180
Country/Region of ManufactureCN
OriginMainland China
High-concerned chemicalNone

Available Gauge Types and Ranges:

  • Boost Gauge 2bar: 0 ~ 2 (x100 kpa)
  • Boost Gauge 3bar: 0 ~ 3 (x100 kpa)
  • Boost Gauge PSI: 0 ~ 30 PSI / 0 to -14.7 PSI
  • Water Temperature Gauge: 50-150°C
  • Oil Temperature Gauge: 50-150°C
  • Oil Pressure Gauge: 0-10 Bar
  • Voltmeter: 8-18 V
  • Air Fuel Ratio Gauge
  • Exhaust Gas Temperature Gauge: 200-1200°C
  • Tachometer: 0-10000 RPM

Setup and Installation

Professional installation is highly recommended for all CNSPEED 620 Series gauges. These gauges are designed for 12-volt automotive systems and are compatible with 4, 6, and 8-cylinder gasoline engines (for tachometer). Each gauge comes with specific accessories and an English instruction manual for detailed wiring and mounting.

General Components Overview

The following image illustrates the typical components included with a CNSPEED 620 Series gauge. Specific sensors and wiring may vary depending on the gauge type.

Various CNSPEED 60mm gauges and their included components, such as mounting pods, wiring harnesses, and sensors.
Figure 1: Overview of CNSPEED 620 Series Gauges and Components

Individual Gauge Components

Below are examples of components typically included with different gauge types. Refer to the specific manual for your gauge for exact details.

Detailed image showing various CNSPEED 60mm gauges (Turbo Boost, Oil Temp, Oil Press, Voltmeter, Air Fuel Ratio, Exhaust Gas Temp, Tachometer) and their respective included components like sensors, wiring, and mounting hardware.
Figure 2: Components for various CNSPEED 620 Series Gauges

Water Temperature Gauge Components

Water Temperature Gauge with its sensor, power cord, signal wires, screws, rubber ring, and instruction manual.
Figure 3: Water Temperature Gauge and its accessories

Voltmeter Components

Voltmeter with its power cord, power series line, rubber ring, instrument cover ring, and instruction manual.
Figure 4: Voltmeter and its accessories

Wiring for Backlight Modes

The gauges feature two backlight modes: White and Amber. The mode is determined by how the positive wires are connected.

Wiring diagram showing connections for different backlight colors: Red+Black for no light, Orange+Black for Amber light, White+Red+Black for White light, and touch White+Red+Black for Amber or White light options.
Figure 5: Backlight Wiring Diagram
  • White Backlight Mode: Connect the positive Red and White wires in parallel.
  • Amber Backlight Mode: Connect the positive Red and Orange-Red wires in parallel.

Operating Instructions

The CNSPEED 620 Series gauges include a power-on self-test, buzzer settings, and options to clear peak values and set alarm points/cylinder counts.

Functional Overview Video

This video demonstrates the power-on sequence and backlight color changes of the gauges.

Video 1: CNSPEED Gauge Power-On and Backlight Demonstration

1. Power-On Self-Test

Upon powering on, the gauge performs a self-test. The backlight and needle behavior depend on the wiring configuration:

  • White Backlight Mode: When positive Red and White wires are connected in parallel, the backlight flashes between white and amber. The needle light and the blue PEAK light illuminate. After the self-test, the backlight remains white, and the PEAK light turns off.
  • Amber Backlight Mode: When positive Red and Orange-Red wires are connected in parallel, the backlight flashes between orange and amber. The needle light and the blue PEAK light illuminate. After the self-test, the backlight remains orange, and the PEAK light turns off.

2. Buzzer Settings

Toggling the Buzzer: If the gauge is currently set to beep and you wish to cancel it, restart the power. Press and hold the button before the tachometer finishes its self-test until the buzzer sound disappears, then release the button. The same process applies to re-enable the sound if it is currently muted.

3. Clearing the PEAK Value (Maximum Memory Value)

The PEAK value is the highest recorded value by the gauge.

  1. After the self-test is complete, press and release the button; the blue PEAK light will turn on.
  2. Press and hold the button again for 3 seconds until the PEAK light flashes.
  3. Release the button to clear the PEAK value. The needle will return to zero after approximately 3 seconds.

4. Setting the Alarm Point and Cylinder Count

This section applies to gauges with alarm functions (e.g., RPM, temperature, pressure).

  • Alarm Point Setting: After the self-test, press and hold the button for 5 seconds until the needle illumination flashes, then release it. Press the button again to set the alarm point (use quick, repeated presses for fine adjustments or hold the button for rapid adjustment). The needle will automatically return to zero after 5 seconds to allow for the next step.
  • Cylinder Setting (for Tachometer): After the self-test or once the needle has returned to zero, press and hold the button for 10 seconds until the needle illumination flashes, then release it. Press the button again to set the cylinder count (4/6/8 cylinders) and then release. After 5 seconds, the needle will automatically return to zero.
  • RPM Alarm Alert: When the RPM alarm is triggered, the lights will flash alternately between Red/White or Red/Orange-Red.

Maintenance

To ensure the longevity and accuracy of your CNSPEED 620 Series gauge, follow these general maintenance guidelines:

  • Regularly inspect all wiring connections to ensure they are secure and free from corrosion.
  • Keep the gauge face clean using a soft, dry cloth. Avoid abrasive cleaners or solvents that could damage the plastic.
  • Ensure the gauge is protected from extreme temperatures and direct moisture exposure.
  • If equipped with sensors, periodically check sensor connections and ensure they are free from debris or damage.

Troubleshooting

Gauge Not Lighting Up

If your gauge is not displaying any light after installation, verify the wiring connections according to the diagram below. Incorrect wiring of the positive and negative terminals is a common cause.

Wiring diagram for troubleshooting a gauge that is not lighting up. Shows correct Red+ and Black- connections for different backlight colors (Amber, White) and an incorrect connection resulting in no light.
Figure 6: Troubleshooting - No Light Wiring
  • No Light: Ensure the Red wire is connected to positive (+) and the Black wire to negative (-). If only Red and Black are connected, there will be no light.
  • Amber Light: Connect Orange wire to positive (+), Red wire to positive (+), and Black wire to negative (-).
  • White Light: Connect White wire to positive (+), Red wire to positive (+), and Black wire to negative (-).

If the issue persists after checking connections, consult a professional automotive electrician.

User Tips

  • Installation Ease: Many users report that the installation process is straightforward, especially with the provided manual.
  • Oil Pressure Sensor Thread: When installing the oil pressure gauge, it's important to verify the thread type of the sensor to ensure compatibility with your vehicle's oil system.

Warranty and Support

For any questions, technical assistance, or warranty claims, please contact the CNSPEED Official Store directly through the platform where you purchased the product. Ensure you have your order details and product model information ready for faster service.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.