Flytec V050-09/V050-10

Contents

Flytec V050-09 Receiving Board and V050-10 Launching Board Instruction Manual

Original Replacement Parts for Flytec Bait Boat V050

1. Product Overview

This product consists of a set of two original replacement circuit boards designed for the Flytec Bait Boat V050: the V050-09 Receiving Board for the boat and the V050-10 Launching Board for the remote control. These components are crucial for the proper functioning of your RC bait boat system, ensuring reliable communication and control.

Image showing both the V050-09 Boat circuit board and the V050-10 Controller circuit board side-by-side.
This image displays both the V050-09 Boat circuit board (left) and the V050-10 Controller circuit board (right), which are replacement parts for the Flytec Bait Boat V050.

2. Setup and Installation

These circuit boards are replacement parts and require careful installation. It is recommended that installation be performed by individuals with experience in electronics or RC model repair. Always ensure the power source is disconnected before beginning any installation or repair work.

2.1 V050-09 Boat Circuit Board Installation

  1. Carefully open the Flytec Bait Boat V050 to access the existing receiving board.
  2. Note the orientation and connection points of all wires and connectors to the old board. Taking photos before disconnection can be helpful.
  3. Gently disconnect all wires and remove the old V050-09 board.
  4. Align the new V050-09 Receiving Board in the same orientation as the old one.
  5. Reconnect all wires and connectors to their corresponding ports on the new board. Ensure all connections are secure and correctly polarized (if applicable).
  6. Before closing the boat, perform a preliminary power-up and test (see Section 3).
Close-up of the V050-09 Boat circuit board with dimensions and weight.
Detailed view of the V050-09 Boat circuit board, showing its components and labeled dimensions: Net Weight: 20g, Size: 5.7cm x 6.8cm x 1.3cm.
Angled view of the V050-09 Boat circuit board.
An angled perspective of the V050-09 Boat circuit board, highlighting its connectors and surface-mounted components.
V050-09 Boat circuit board with dimensions 6.8cm, 5.7cm, 1.3cm.
The V050-09 Boat circuit board with its length (6.8cm), width (5.7cm), and height (1.3cm) clearly indicated.

2.2 V050-10 Remote Control Circuit Board Installation

  1. Open the Flytec Bait Boat V050 remote control casing.
  2. Carefully observe and document the existing V050-10 board's connections and layout.
  3. Disconnect all wires and remove the old launching board.
  4. Install the new V050-10 Launching Board, ensuring correct alignment and secure connections for all wires, buttons, and the joystick.
  5. Before reassembling the remote control, perform a preliminary power-up and test (see Section 3).
Close-up of the V050-10 Remote Control Circuit Board with dimensions and weight.
Detailed view of the V050-10 Remote Control Circuit Board, showing its buttons, joystick, and labeled dimensions: Net Weight: 20g, Size: 9.5cm x 3.4cm x 2cm.
V050-10 Remote Control Circuit Board with dimensions 9.5cm, 3.4cm, 2cm.
The V050-10 Remote Control Circuit Board with its length (9.5cm), width (3.4cm), and height (2cm) clearly indicated.

3. Operating Instructions

Once both the V050-09 Receiving Board and V050-10 Launching Board are correctly installed, their operation is integrated into the overall functionality of your Flytec Bait Boat V050 system. These boards facilitate the communication between your remote control and the boat, enabling functions such as propulsion, steering, and bait release.

  1. Power On: Ensure the boat's battery is charged and connected, then power on the boat. Next, power on the remote control.
  2. Pairing: The boards should automatically establish a connection. If not, refer to your Flytec Bait Boat V050's main manual for specific pairing procedures.
  3. Function Test: Test all remote control functions (forward, backward, left, right, bait release, light control, etc.) to ensure the new boards are working correctly and communicating with each boat component.
  4. Water Test: After successful dry testing, perform a test in water to confirm full operational integrity.

4. Maintenance

To ensure the longevity and optimal performance of your circuit boards, follow these general maintenance guidelines:

  • Keep Dry: Always protect the circuit boards from moisture and water exposure. Water damage can lead to short circuits and irreversible damage.
  • Cleanliness: Keep the boards free from dust, dirt, and debris. Use a soft, dry brush or compressed air for cleaning. Avoid using liquids or harsh chemicals.
  • Physical Protection: Ensure the boat and remote control casings are properly sealed to protect the boards from physical impact and environmental elements.
  • Battery Care: Use only recommended batteries and chargers. Overcharging or using incompatible power sources can damage electronic components.

5. Troubleshooting

If you encounter issues after installing the new circuit boards, consider the following troubleshooting steps:

  • No Power/No Response:
    • Check all battery connections in both the boat and the remote control.
    • Ensure batteries are fully charged.
    • Verify that the power switches are in the 'ON' position.
  • Boat Not Responding to Remote:
    • Confirm both the boat and remote control are powered on.
    • Check for proper pairing between the boat and remote. Refer to your main boat manual for pairing instructions.
    • Inspect all wire connections to both the V050-09 and V050-10 boards for looseness or incorrect placement.
  • Partial Functionality (e.g., only steering works, no propulsion):
    • This often indicates a specific connection issue. Re-check the wiring for the non-functional component on the V050-09 board.
    • Ensure no wires are pinched or damaged during reassembly.
  • Board Appears Damaged or Non-functional Upon Receipt:
    • If a newly received board does not work, or appears physically damaged, cease installation and contact the seller immediately. (As noted in user reviews, sometimes boards can be faulty upon arrival).

6. Specifications

FeatureDescription
BrandFlytec
Model NumbersV050-09 (Boat Circuit Board), V050-10 (Remote Control Circuit Board)
UsageFor Flytec Bait Boat V050
MaterialComposite Material
CertificationCE
Recommended Age14+ years
V050-09 Board Net Weight20g
V050-09 Board Size5.7cm x 6.8cm x 1.3cm
V050-10 Board Net Weight20g
V050-10 Board Size9.5cm x 3.4cm x 2cm
Quantity1 pair (one V050-09 and one V050-10)

7. User Tips

  • Careful Replacement: Users have reported successful replacements, stating that after replacing the circuit boards, their boat and remote control worked perfectly, running like new. This highlights the importance of careful and correct installation.
  • Test Upon Receipt: One user reported receiving a damaged board that did not work. It is advisable to visually inspect and, if possible, test the boards upon receipt to ensure they are in working condition before full installation.
  • Verify All Connections: Ensure all wires are securely connected and in the correct ports. Loose or incorrect connections are a common cause of non-functionality.

8. Warranty and Support

As these are original replacement parts from the Flytec Official Store, any warranty claims or support inquiries should be directed to the seller or manufacturer. Please retain your proof of purchase for any potential claims.

If you receive a product that is not working or appears damaged, please contact the seller immediately for assistance.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.