1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your RACBOX 3-in-1 LED Tail Brake Light. This product is designed as an auxiliary accessory for automotive lighting, serving as a replacement and upgrade for original vehicle lights. It is suitable for a wide range of 12V and 24V vehicles, including heavy-duty trucks, semi-trailers, cargo trailers, boat trailers, work vehicles, tractors, lorries, buses, pickups, and vans.
The light features a 3-in-1 design, incorporating a neon halo ring for tail and brake functions, and sequential flowing signal lights for turn indications. It is completely sealed and boasts an IP67 waterproof rating, ensuring durability in various weather conditions. Each light is equipped with 28pcs 2835 Super Bright LEDs and 72pcs 2835 SMD LED Diodes for bright and efficient performance.
Figure 1: RACBOX 3-in-1 LED Tail Brake Light (2nd Generation)
2. Safety & Warnings
Important Safety Information: Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
- Keep the device and its cord out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Follow installation and operation guidelines to avoid injury.
3. Specifications
| Feature | Specification |
|---|---|
| Model Name | Stop turn tail brake marker Clearance Lamp |
| Voltage | 12 V / 24 V (DC10-30V) |
| Lumens | 3000LM |
| Item Type | Turn Signal |
| Waterproof Level | IP67 |
| Functions | Clearance, side marker, identification, stop, turn, tail, brake, running, reverse light |
| Material | PC+ABS (Polycarbonate Lens) |
| LED Type | 2835 SMD |
| Special Features | 3 modes in 1 Neon Halo Ring Light |
| Light Color | Red + Yellow |
| Lens Color | Red, Transparent |
| Wattage & Current (Running Light) | 0.05A / 0.65W |
| Wattage & Current (Brake Light) | 0.17A / 2.2W |
| Wattage & Current (Turn Signal) | 0.28A / 3.65W |
| Power | 0.7 W |
| Color Temperature | 3000K |
| Life Span | 30,000 hours |
| Dimensions (L x W x H) | 233mm x 42mm x 16mm |
| Bolt Distance (Center to Center) | 214mm |
Figure 2: Product Dimensions
Figure 3: Detailed Product Parameters
4. Installation (Setup)
Follow these steps for proper installation of the LED Tail Brake Light:
- Turn off the engine and ensure the vehicle is parked safely.
- Open the trunk lid and remove the interior cover or lining behind the tail light.
- Locate and remove the fixing nuts or bolts that secure the original tail light assembly.
- Unplug the wiring harness connector from the stock tail light.
- Carefully remove the original tail light assembly from the vehicle body.
- Install the new tail light assembly into the mounting position, ensuring it fits correctly.
- Reconnect the wiring harness plug. If the light does not work, reverse the plug polarity.
- Secure the tail light with nuts or bolts and reinstall the interior cover.
- Test all functions: brake light, turn signal, reverse light, and running light.
- Check for any gaps or loose parts to ensure a firm and stable installation.
Wiring Connection Diagram:
Figure 4: Wiring Diagram
- Black Wire: Negative
- Yellow Wire: Turn light
- Red Wire: Stop Light (Brake Light)
- Blue Wire: Tail Light (Left)
- Green Wire: Tail Light (Right)
Component Details:
Figure 5: Transparent Shell and Spotlight Beads
The light features a stable outer casing for uniform brightness and high-power spotlight beads for concentrated, bright light with low energy consumption.
Figure 6: Stabilizing Screws and Strengthened Wiring
Fine-crafted stabilizing screws with textured hardware threads ensure easy installation. The wiring is strengthened for wear resistance and easy connection.
5. Operating Instructions
The RACBOX 3-in-1 LED Tail Brake Light offers multiple lighting modes for various vehicle functions:
- Running Light: Provides a continuous, uniform glow for visibility.
- Brake Light: Illuminates brightly and immediately upon braking, featuring a neon halo ring effect.
- Turn Signal: Displays a sequential flowing amber light, indicating the direction of turn.
- Startup Effect: Features a cool dynamic scanning light effect when the vehicle is started.
Figure 7: Luminous Effects and Modes
The product is designed for low power consumption while providing strong, concentrated illumination.
Video 1: Product Demonstration of Light Functions
6. Maintenance
To ensure the longevity and optimal performance of your LED Tail Brake Light, follow these maintenance guidelines:
- Cleaning: Regularly clean the lens with a soft, damp cloth to remove dirt and debris. Avoid abrasive cleaners or solvents that could damage the polycarbonate lens.
- Inspection: Periodically check the wiring connections for any signs of wear, corrosion, or looseness. Ensure all mounting bolts are secure.
- Waterproof Integrity: While the product is IP67 waterproof, avoid high-pressure washing directly onto the light for extended periods, which could compromise seals over time.
Figure 8: IP67 Waterproof Feature
7. Troubleshooting
If you encounter issues with your LED Tail Brake Light, refer to the following common problems and solutions:
- Light Not Functioning:
- Check the wiring connections. Ensure all wires are securely connected according to the wiring diagram (Figure 4).
- If the light does not work after initial connection, reverse the plug polarity.
- Verify the vehicle's power supply (12V or 24V) is correct and fuses are intact.
- Intermittent Operation or Dim Light:
- Inspect for loose wiring connections or corrosion at the terminals.
- Ensure the vehicle's electrical system is providing stable voltage.
- Loose Installation:
- Re-check and tighten all stabilizing screws and mounting bolts (Figure 6) to ensure a firm and stable installation.
8. User Tips
- Easy Installation: Users have noted the product is easy to install, making it a convenient upgrade or replacement.
- Brightness: The lights are reported to be very bright, enhancing visibility and safety.
- Aesthetic Appeal: Many users appreciate the modern look and feel the lights provide to their vehicles.
- Brake Light Functionality: The brake lights activate immediately upon voltage application, without a flash option. The sequential flowing effect is specifically for the turn signals.
9. Warranty & Support
Compliance Information:
This product is an auxiliary accessory for automotive lighting and is only used for the normal replacement and upgrade of the original car lights, not for illegal modification or illegal use. The products meet the relevant national automotive lighting industry standards, and have undergone strict quality testing before leaving the factory, and are qualified to leave the factory.
Standard Warranty:
RACBOX warrants to the first end-user that this product shall materially conform to RACBOX's published specifications in the user manual. The Warranty Period for a new Product is ONE Year (12 Months) from the date a new product is first delivered to the End-User after being purchased. Customers will be covered for replacement parts and shipping costs during the Warranty Period for any product due to manufacturing defects of components or workmanship.
What is NOT Covered:
The Warranty does not cover any damage due to abuse, wrong installation, neglect or misuse, extreme environment, unusual physical or electrical stress or interference, exposure to flooding, fire, or electrical problems associated with incoming power or other acts not the fault of Racbox. The Warranty does not cover accessory parts. Racbox is not responsible for damage arising from end-user error and failure to follow instructions relating to Product's use.
How to Get Warranty Service:
If you have any questions or need to request a replacement part within your limited warranty, please feel free to contact our customer support, either by phone, email, or through our Live Support system.
Figure 9: RACBOX Warranty Overview
10. Frequently Asked Questions (FAQ)
- Q: Do the rear lights have no flash option... do they turn on immediately when voltage is applied during braking?
- A: The brake lights activate immediately upon voltage application, without a flash option. The sequential flowing effect is for the turn signals.