1. Product Overview
This manual provides instructions for the Hongwin 25620-02511 Coolant Thermostat. This component is crucial for regulating your engine's operating temperature, ensuring optimal performance and efficiency. It is designed for high accuracy and features a hermetically sealed, compact design.
Compatible Vehicles:
- Kia Picanto SA (2004-2010), New Morning
- Hyundai Atos & Amica 1.0, 1.1
- Hyundai Friend 1.0, 1.1
- Hyundai Amica / Atoz (MX) 1.1 (08-2003 to 05-2005)
- Hyundai Amica (MX) 1.1 (06-2003 onwards, 09-2005 onwards)
- Hyundai Atos (MX) 1.1 (08-2003 to 05-2005)
- Hyundai Atos Prime (MX) 1.1 (06-2003 onwards, 09-2005 onwards)
- Hyundai Atoz (MX) 1.1 (08-2003 to 05-2005)
- Hyundai Santro Xing (MX) 1.1 (08-2003 to 05-2005)

Figure 1: Hongwin 25620-02511 Coolant Thermostat Assembly with 4-pin connector detail.
2. Setup and Installation
Important: Installation of automotive cooling system components should ideally be performed by a qualified mechanic. Improper installation can lead to engine damage or personal injury.
2.1 Safety Precautions
- Ensure the engine is completely cool before starting any work.
- Disconnect the vehicle's battery to prevent electrical hazards.
- Wear appropriate personal protective equipment (gloves, eye protection).
- Be prepared for coolant spillage; have a drain pan ready.
2.2 Pre-Installation Checks
- Verify Part Compatibility: Carefully compare the new thermostat with the old one, paying close attention to dimensions, hose connections, and the electrical plug type (this model uses a 4-pin connector). Refer to Figure 2 for a visual comparison of long vs. short versions.
- Inspect for Damage: Before installation, visually inspect the new thermostat for any signs of damage during shipping.

Figure 2: Ensure you have the correct 'long' version of the thermostat for proper fitment.
2.3 General Installation Steps (Consult Vehicle Service Manual for Specifics)
- Drain Coolant: Place a drain pan under the radiator and open the drain cock to drain the coolant.
- Locate Old Thermostat: Identify the thermostat housing, usually located at the engine end of the upper radiator hose.
- Remove Hoses and Housing: Loosen hose clamps and remove the hoses connected to the thermostat housing. Carefully unbolt and remove the thermostat housing.
- Remove Old Thermostat: Take out the old thermostat and clean the mating surfaces thoroughly, removing any old gasket material.
- Install New Thermostat: Place the new Hongwin thermostat in the housing, ensuring it is oriented correctly. Apply a new gasket if required by your vehicle's design.
- Reassemble: Reattach the thermostat housing, hoses, and tighten all bolts and clamps to manufacturer specifications.
- Connect Electrical Plug: Carefully connect the 4-pin electrical plug to the thermostat sensor. Ensure it clicks securely into place. (See Figure 3 for plug detail).
- Refill Coolant: Refill the cooling system with the manufacturer-recommended coolant.
- Bleed Air: Start the engine and allow it to reach operating temperature with the heater on full. Monitor the coolant level and add more as needed. Bleed any air from the system according to your vehicle's service manual.
- Check for Leaks: After the engine has run for a while, shut it off and inspect all connections for any signs of leaks.

Figure 3: Close-up of the 4-pin electrical connector.
3. Operating Instructions
The Hongwin 25620-02511 Coolant Thermostat operates automatically to maintain your engine's optimal operating temperature. It opens to allow coolant to flow to the radiator when the engine reaches a certain temperature and closes to restrict flow when the engine is cold, helping it warm up faster.
No user intervention is required for the operation of the thermostat itself once correctly installed.
4. Maintenance
The thermostat itself is a sealed unit and does not require specific maintenance. However, regular maintenance of your vehicle's cooling system is essential for the thermostat's longevity and proper function:
- Coolant Level: Regularly check your coolant level and top it off with the correct type of coolant as needed.
- Coolant Condition: Follow your vehicle manufacturer's recommendations for coolant flush and replacement intervals. Old or contaminated coolant can lead to thermostat failure.
- Hose Inspection: Periodically inspect all cooling system hoses for cracks, leaks, or bulges.
- Leak Checks: Look for any signs of coolant leaks around the thermostat housing or other cooling system components.
5. Troubleshooting
A faulty thermostat can lead to various engine problems. If you experience any of the following symptoms, it may indicate a thermostat issue:
- Engine Overheating: The temperature gauge consistently reads high, or the engine overheats, especially in traffic. This can happen if the thermostat is stuck closed.
- Engine Not Reaching Operating Temperature: The temperature gauge remains low, or the engine takes a very long time to warm up. This can happen if the thermostat is stuck open.
- Erratic Temperature Gauge: The temperature gauge fluctuates wildly, indicating inconsistent temperature regulation.
- Poor Heater Performance: If the engine isn't reaching proper operating temperature, the cabin heater may not produce sufficient heat.
If you suspect a faulty thermostat, it is recommended to have your vehicle diagnosed by a professional mechanic.
6. Specifications
| Feature | Specification |
|---|---|
| Brand | Hongwin |
| Model Number | 25620-02511 |
| OEM NO. | 25620 02511, 25620-02511, 2562002511, V52990021, 25600 02566, 25600-02566, 25650-02560, 2565002560 |
| Interchange Part Number | 25600 02566, 2565002560 |
| Placement on Vehicle | Coolant Thermostat |
| Material | PA66-GF30, PA66-GF35 |
| Origin | Mainland China |
| Item Weight | 400g |
| Overall Length | 111mm / 4.37" (See Figure 4) |
| Mounting Flange Diameter | 32.5mm / 1.28" (See Figure 5) |
| Small Hose Connection | 12.5mm / 0.49" (See Figure 6) |
| Main Hose Connections | 24mm / 0.94", 16mm / 0.63" (See Figure 7) |
| Sensor Housing Connections | Various, including 15mm / 0.59", 23.5mm / 0.92" (See Figure 8) |
| Electrical Connector | 4-pin |

Figure 4: Overall length measurement of the thermostat assembly.

Figure 5: Mounting flange diameter measurement.

Figure 6: Small hose connection diameter measurement.

Figure 7: Main hose connection diameter measurements.

Figure 8: Sensor housing and various connection measurements.
7. User Tips
- Always ensure the replacement thermostat matches the original part exactly in terms of dimensions and connector type to avoid fitment issues.
- When replacing the thermostat, it's a good practice to also replace the thermostat housing gasket to prevent leaks.
- Consider flushing your cooling system when replacing the thermostat to ensure clean coolant and optimal system performance.
8. Warranty and Support
8.1 Warranty Information
This Hongwin Coolant Thermostat comes with a 1-year warranty from the date of purchase. The warranty covers manufacturing defects. Please retain your proof of purchase for warranty claims.
8.2 Manufacturer Contact Information
Manufacturer: Wenzhou Haowei Auto Parts Co., Ltd.
Manufacturer Address: Floor 2, Building 8 (West), Hantian Hardware and Electrical City, Tangxia Town, Ruian City, Zhejiang Province, China
Customer Service Email: inf@hwautoparts.com
Telephone: +86-18005775583
For further assistance, you may also refer to the official user manual PDF available from the seller.
9. Packaging Safety Warning
WARNING:
TO AVOID DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, CARRIAGES, OR PLAY PENS. THIS BAG IS NOT A TOY.