Fuers M558 Wireless Doorbell

Contents

Fuers M558 Wireless Doorbell User Manual

Model: M558

Important Information

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

Special Note: Do not install the transmitter on metal doors as much as possible, otherwise it may affect the emission distance.

This wireless doorbell has a power outage memory function. If power is lost and then restored, the doorbell will remember the last selected ringing sound.

Product Overview

The Fuers M558 Wireless Doorbell system consists of a receiver and a waterproof transmitter button. It features 33 selectable songs, 4 adjustable volume levels, and a long transmission range.

Fuers M558 Wireless Doorbell receiver and transmitter
Fuers M558 Wireless Doorbell receiver and transmitter, highlighting features like accurate alarm, 33 songs, and 4 level volumes, and IP55 waterproof rating.

Setup and Installation

1. Receiver Setup

  1. Plug the doorbell receiver into a standard AC outlet.
  2. The receiver will ring "Dingdong" once, indicating it has entered working mode.

2. Transmitter Installation

  1. Tear off the adhesive backing from the doorbell transmitter.
  2. Stick the transmitter firmly onto the desired wall surface. Press and hold for more than 5 seconds to ensure proper adhesion.
  3. After confirming the transmitter is firmly fixed, press the transmitter button. The receiver will emit a melody, indicating the transmitter is working normally.
Diagram showing doorbell receiver and button installation
Diagram showing the receiver (220V AC, plug and play) and the button (fixed with double-sided tape, built-in battery).
Doorbell receiver plugged in and transmitter button being pressed
Installation example showing the receiver plugged into a wall outlet and the transmitter button being pressed.

3. Pairing (Common Doorbell Button Learning)

  1. Short press the [Set] button on the receiver. The doorbell receiver will ring once, then release your hand.
  2. Press the button on the doorbell transmitter. The doorbell receiver will "ding dong" once, indicating successful pairing.

4. Factory Reset

  1. Unplug the doorbell receiver from the socket.
  2. Press and hold the [Volume] button on the receiver.
  3. While holding the [Volume] button, plug the receiver back into the socket. Hold for 3 seconds.
  4. The doorbell receiver will emit a beep, indicating that all transmitters and detectors have been successfully deleted and factory settings restored.

Note: The product is typically pre-paired at the factory. Users do not usually need to configure it unless adding new transmitters or resetting.

Setup Demonstration Video

This video demonstrates the doorbell's functions including plugging in the receiver, pressing the button, changing melodies, adjusting volume, and activating the SOS alarm.

Operation Guide

1. Adjusting Volume

Press the [Volume] button on the receiver to adjust the volume. There are 4 levels available.

2. Selecting Melody

Press the [Select Song] button on the receiver to choose from 33 available melodies.

Doorbell receiver showing volume and song selection
The receiver features 4 levels of adjustable volume and 33 optional songs.

3. SOS Alarm Function

The doorbell also supports an SOS alarm function. This is typically activated by a specific button press sequence or dedicated SOS button on the transmitter (if available). Refer to the video demonstration for how to activate the SOS alarm.

4. Long Distance Transmission

The doorbell offers a strong signal with a long operating range of up to 150 meters (500 feet) in open spaces, making it suitable for large houses, villas, apartments, offices, shops, and warehouses.

Diagram illustrating doorbell signal transmission through obstacles
Diagram illustrating strong signal transmission up to 150m (500ft) in open space, passing through walls and doors.

Maintenance

The doorbell transmitter is designed with an IP55 waterproof and dustproof rating, ensuring durability in various weather conditions.

Waterproof doorbell transmitter with temperature and lifespan details
Close-up of the waterproof transmitter, detailing IP55 rating, -10°C to -50°C working temperature, and 3-year maximum lifespan.

Battery Replacement

The transmitter uses a CR2032 button battery. When the battery is low, the transmission range may decrease or the doorbell may stop functioning. Replace the battery by carefully opening the transmitter casing and inserting a new CR2032 battery, ensuring correct polarity.

Cleaning

Wipe the doorbell units with a soft, dry cloth. Avoid using abrasive cleaners or solvents.

Troubleshooting

  • No sound from receiver: Ensure the receiver is properly plugged into a live AC outlet. Check if the volume is turned up. Re-pair the transmitter and receiver if necessary.
  • Transmitter not working: Check the battery in the transmitter (CR2032). Replace if necessary. Ensure the transmitter is not installed on a metal surface that could interfere with the signal.
  • Shortened transmission range: Replace the transmitter battery. Ensure there are no significant metal obstructions between the transmitter and receiver.
  • Interference: If the equipment causes harmful interference to radio or television reception, try the following:
    1. Reorient or relocate the receiving antenna.
    2. Increase the separation between the equipment and receiver.
    3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
    4. Consult the dealer or an experienced radio/TV technician for help.

Specifications

Feature Receiver Transmitter
Working Voltage AC 100-240V 3V (CR2032 button battery)
Working Current <100mA 8mA
Wireless Frequency 433MHz 433MHz
Working Temperature -10°C to 50°C -10°C to 50°C
Wireless Distance 100 meters (Open area)
Volume Decibels 20-100db (4 levels adjustable) N/A
Receiver Size 97*48*17mm (Not including plug) N/A
Transmitter Size N/A 79*40*11mm
Connection Type Wireless
Item Type Wireless Doorbell
Alarm Function Yes
Power Source Electric Supply
Certifications CE, FCC

User Tips

  • Excellent Range: Users report good performance even with the doorbell button outside and the receiver upstairs, working well over distances of 10 meters and more. The signal is strong and reaches far.
  • Easy Installation: The setup process is straightforward and quick.
  • Volume and Melodies: The doorbell offers 4 levels of adjustable volume and 33 different melodies to choose from, allowing for personalization.
  • Melody Memory: The doorbell remembers your last selected melody even after a power outage.

Warranty and Support

For detailed warranty information and further support, please refer to the official user manual PDF provided by Fuers. You can typically find this document on the product's support page or by contacting Fuers customer service.

The official user manual (PDF) can be referenced at: Fuers M558 User Manual PDF

FCC Compliance Statement

FCC ID: 2BEQ7-M558

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Important: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user's authority to operate the equipment.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.