SLMPLEFUN 1208

Contents

Universal Wireless Remote Control Switch

Model: 1208

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Universal Wireless Remote Control Switch. This 8-channel RF 433MHz system is designed for controlling various electrical devices such as garage doors, lights, motors, and automated curtains, offering a control distance of up to 500 meters in open space.

Universal Wireless Remote Control Switch components: receiver board, remote control, and housing.

The system consists of a DC 12V relay receiver and a multi-button remote control transmitter. Please read this manual thoroughly before use to ensure proper and safe operation.

2. Safety Information

  • **Important:** Signal pairing is required before initial use. Refer to the 'Setup' section for instructions.
  • Ensure all power is disconnected before performing any wiring or installation to prevent electric shock.
  • This device operates with electrical currents (1~250V input/output). Handle with care and ensure proper insulation.
  • Do not expose the device to extreme temperatures, moisture, or corrosive environments.
  • Keep the device out of reach of children.
  • Handle the receiver housing carefully, as some users have noted it may have weak protection.

3. Product Overview

3.1 Components

  • Receiver Module: DC 12V, 8-channel relay with passive output (dry contact 1~250V).
  • Remote Control Transmitter: 8-button digital remote with extendable antenna, powered by a 23A 12V battery.
Remote control with extendable antenna, indicator light, and 23A 12V battery included. Dimensions: 90x40x14mm.

Image: Remote Control Transmitter with dimensions and battery type.

3.2 Typical Applications

This versatile remote control switch can be used in various scenarios, including:

  • Home Automation: Controlling lights, fans, automated curtains, garage doors, and gates.
  • Industrial Use: Operating cranes, telescopic doors, and other machinery.
  • Commercial Settings: Stage lighting, barrier control, and sliding doors.
Diagram showing various applications: Crane, Telescopic door, Stage lighting, Lamp, Sliding door, Garage Door, Courtyard gate, Barrier.

Image: Examples of application scenarios.

4. Specifications

Parameter Value
Working Voltage (Receiver)DC 12V
Input Voltage1~250V
Output Voltage1~250V (dry contact)
Number of Channels8
Quiescent Current<5mA
Max Current10A
Max Load2200W
RF Frequency433MHz
Working Temperature-30~+80°C
Receiving Sensitivity>97dbm
Amount of Storage Remote Controls25 pieces
Support Encoding1527 Leaning code/2262 fixed code
RF Operating ModeASK superheterodyne wireless reception
Remote Control DistanceOpen space is more than 500 meters
Remote Operating ModesMomentary Mode / Toggle Mode / Latched Mode
Output TerminalNO / COM / NC
Receiver Dimensions96*71*25mm
Remote Control Dimensions90*40*14mm
Remote Control Battery23A 12V
CertificationCE, RoHS

5. Setup and Wiring

5.1 Receiver Components

Detailed view of the receiver board showing V+, V-, Indicator Light, Learning Button, Jumper Cap, NC, COM, NO terminals. Dimensions: 96x71x25mm.

Image: Receiver board with labeled components.

  • V+, V-: Power input terminals (DC 12V).
  • Indicator Light: Shows status and learning process.
  • Learning Button: Used for pairing remote controls and clearing data.
  • Jumper Cap: Configures the operating mode (Momentary, Toggle, Latched).
  • NO (Normally Open), COM (Common), NC (Normally Closed): Relay output terminals (dry contact).

5.2 Wiring Diagrams

Ensure power is OFF before wiring. Connect the DC 12V power supply to the V+ and V- terminals on the receiver board. Connect your device (e.g., light, motor) to the NO, COM, or NC terminals based on your desired operation.

5.2.1 Wiring for AC Motor Control

Wiring diagram for controlling an AC motor with the receiver. Shows AC 1-250V input to the motor and relay connections.

Image: Wiring diagram for an AC motor.

5.2.2 Wiring for Light Control

Wiring diagram for controlling 1-250V lights with the receiver. Shows power input and relay connections to multiple lights.

Image: Wiring diagram for lights.

6. Operating Modes and Remote Pairing

6.1 Delete Existing Remote Data (First Application)

When you receive the product, it may have been randomly set to a remote mode during testing. For the first application, it is recommended to clear all existing data:

  1. Press and hold the learning button on the receiver for 5 seconds.
  2. The existing data will be deleted successfully.

6.2 Setting Operating Modes

The operating mode is configured using the jumper cap on the receiver board. Refer to the image below for the jumper cap location.

Close-up of the receiver board showing the jumper cap and learning button.

Image: Jumper cap location on the receiver board.

6.2.1 Momentary Mode

Description: Press and hold a button on the remote, the relay turns ON. Release the button, the relay turns OFF.

Setup:

  1. Ensure the Jumper Cap is NOT connected to any pins (Pin 1, 2, 3, 4 are all disconnected).
  2. Press the learning button on the receiver 1 time. Wait for 3 seconds.
  3. Press button '1' on the remote control. Wait for 3 seconds. Pairing is successful.

6.2.2 Toggle Mode

Description: Press a button on the remote, the relay turns ON. Press the same button again, the relay turns OFF.

Setup:

  1. Connect the Jumper Cap to Pin 1 and Pin 2.
  2. Press the learning button on the receiver 1 time. Wait for 3 seconds.
  3. Press button '1' on the remote control. Wait for 3 seconds. Pairing is successful.

6.2.3 Latched Mode

Description: Press button '1' on the remote, relay '1' turns ON. Press button '2' on the remote, relay '2' turns ON, and relay '1' turns OFF simultaneously.

Setup:

  1. Connect the Jumper Cap to Pin 3 and Pin 4.
  2. Press the learning button on the receiver 1 time. Wait for 3 seconds.
  3. Press button '1' on the remote control. Wait for 3 seconds. Pairing is successful.

7. User Tips

  • Simple Operation: The system is designed for straightforward use. Once paired, the remote control provides reliable operation.
  • Extended Range: Users have noted the excellent control distance. For optimal range, ensure the remote's antenna is extended and there are no major obstructions between the remote and the receiver.
  • Value for Money: This product offers good performance for its cost.
  • Receiver Protection: While generally robust, some users have reported that the receiver's vent area might be susceptible to damage. Consider placing the receiver in a protected location or adding additional enclosure if it will be exposed to physical impact.

8. Maintenance

  • Keep the receiver and remote control clean and dry.
  • Avoid dropping or subjecting the devices to strong impacts.
  • Replace the remote control battery (23A 12V) when the control range decreases or the indicator light dims.
  • Periodically check wiring connections for security and integrity.

9. Troubleshooting

  • Device not responding:
    • Check if the receiver is powered correctly (DC 12V).
    • Ensure the remote control battery is not depleted.
    • Verify that the remote control is properly paired with the receiver (refer to Section 6.1 and 6.2).
    • Check for any obstructions between the remote and receiver.
  • Intermittent operation:
    • Check for sources of RF interference (e.g., other wireless devices, large metal objects).
    • Ensure the remote control battery is strong.
    • Re-pair the remote control with the receiver.
  • Incorrect relay behavior:
    • Verify the jumper cap setting matches the desired operating mode (Momentary, Toggle, Latched).
    • Clear all existing remote data and re-pair the remote control.

10. Regulatory Information

This product complies with CE and RoHS certification standards.

Manufacturer: Huizhou Wenqiao Electronic Technology Co., Ltd.

Address: Room 03, 12th Floor, Building T19, East Coast Garden, Fangzhilonghuwan, No. 27, Sanhuan South Road, Huicheng District, Huizhou City, Guangdong Province, China 516001

Email: dieseelectronic@163.com

11. Support

For further assistance or detailed diagrams, you may refer to the official user manual PDF:

A PDF version of this manual is available for download. Please check the product page or contact customer support for the direct link: https://manuals.plus/m/8da7a2dc9de7c08a87f855b8be57f9aeceef8330d1713ee11562fd653e2d5926

For any issues not covered in this manual, please contact your retailer or the manufacturer's support team.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.