BALASHOV P5

Contents

BALASHOV Automatic Foam Soap Dispenser

Model: P5

User Manual

1. Introduction

Thank you for choosing the BALASHOV Automatic Foam Soap Dispenser. This touchless infrared sensor dispenser provides a hygienic and convenient way to dispense foam soap, promoting better hand hygiene. Please read this manual carefully before use and retain it for future reference.

BALASHOV Automatic Foam Soap Dispenser dispensing foam into hands.
The BALASHOV Automatic Foam Soap Dispenser in operation, providing foam soap.

2. Safety Information

  • Do not immerse the device in water or other liquids.
  • Do not use abrasive cleaners or harsh chemicals on the device.
  • Keep out of reach of children.
  • Ensure the charging port is dry before connecting the USB cable.
  • Use only the provided USB charging cable or a compatible one.
  • Avoid direct sunlight or strong light exposure to the infrared sensor.

3. Package Contents

Please check that all items are included in your package:

  • Automatic Foam Soap Dispenser (Model P5)
  • USB Charging Cable
  • User Manual (PDF version available at PDF Manual)
  • Small bottle for liquid transfer (may vary by package)

4. Product Overview

The dispenser features a sleek design with a separable bottle for easy refilling and cleaning. It includes a touch sensor for power and gear switching, an infrared sensor for touchless dispensing, and a USB charging port.

Diagram of the Automatic Soap Dispenser showing touch area, indicator light, nozzle, and charging port.
Key components of the dispenser: Touch area, Indicator light, Nozzle, and Charging port.
Product dimensions diagram showing height 187mm, top width 107mm, and base width 72mm, with charging port location.
Product dimensions and charging port location.
Diagram illustrating the 45-degree tilt angle design of the dispenser nozzle for ergonomic use.
The 45° tilt angle design ensures comfortable and natural foam dispensing.

5. Setup

5.1 Charging the Device

  1. Locate the USB charging port on the side of the dispenser. It is usually covered by a small flap.
  2. Open the charging hole flap.
  3. Connect the provided USB charging cable to the dispenser and a suitable USB power source (e.g., computer, wall adapter).
  4. The indicator lights will show charging status. Ensure the device is fully charged before first use.
Image showing the USB-C charging port on the side of the dispenser, labeled 'USB Charging'.
USB Charging port location.

5.2 Filling the Soap Dispenser

  1. Separate the top machine part from the bottom liquid bottle by twisting or pulling gently.
  2. Pour your preferred liquid soap into the bottle. For optimal foaming, it is recommended to dilute liquid soap with water. A common ratio is 1 part soap to 1-2 parts water (e.g., 50% soap, 50% water, or 1 part soap to 2 parts water). Mix gently.
  3. Reattach the top machine part securely to the liquid bottle.
Diagram showing the separable bottle design and different liquid types (blue and red) that can be used.
The dispenser features separable bottles for easy refilling with various liquids.

6. Operating Instructions

6.1 Power On/Off

  • Turn On: Press the touch area (usually marked with a fingerprint icon) once. LED1 will light up for 2 seconds, indicating the device is on.
  • Turn Off: Long press the touch area for 2 seconds. LED1 and LED4 will flash for 3 seconds, indicating the device is off.
  • Standby Mode: The dispenser will automatically enter standby mode if it is not used for a long time. There is no need to manually turn it off in this case.

6.2 Adjusting Dispensing Volume (Gear Switch)

  • After turning on the device, press the touch area (power button) briefly to cycle through the dispensing gears.
  • The dispenser has 4 gears with dispensing times of 0.3s, 0.8s, 1.5s, and 2s. Each press will switch to the next gear.

6.3 Dispensing Soap

  • Place your hand below the dispensing nozzle, within a distance range of 0-70mm.
  • The infrared sensor will detect your hand, and the machine will automatically dispense foam soap according to the selected gear.
Close-up of the dispenser actively producing foam into a hand.
The dispenser automatically releases foam when a hand is detected.

7. Maintenance

7.1 Cleaning Mode

  • To activate cleaning mode, turn on the machine and then triple-click the touch area (power button).
  • The machine will run a cleaning cycle for 10 seconds.
  • You can manually stop the cleaning mode by pressing the touch area (power button) again.

7.2 General Cleaning

  • Wipe the exterior of the dispenser with a soft, damp cloth.
  • Do not use harsh chemicals or abrasive materials.
  • Ensure the nozzle is clear of any dried soap residue.

7.3 Refilling

  • When the soap level is low, separate the bottle and refill as described in Section 5.2.
  • Always ensure proper dilution of liquid soap for optimal foam production.

8. Troubleshooting

Problem Possible Cause Solution
Lights flash but no soap dispenses.
  • Low battery.
  • No soap or insufficient soap in the bottle.
  • Soap too thick or clogged nozzle.
  • Sensor obstructed.
  • Charge the device fully.
  • Refill the soap bottle.
  • Dilute the soap with water (1:1 or 1:2 ratio) and run cleaning mode.
  • Ensure nothing is blocking the sensor or nozzle.
Device does not turn on after charging.
  • Not fully charged.
  • Incorrect power on procedure.
  • Ensure the device is charged until indicator lights confirm full charge.
  • Press the touch area once to turn on (LED1 lights for 2s).
No foam or weak foam.
  • Soap not diluted properly.
  • Wrong type of liquid (not foaming soap).
  • Dilute liquid soap with water (recommended 1 part soap to 1-2 parts water).
  • Use foaming hand soap or liquid soap suitable for dilution.
Dispenser continuously runs or dispenses soap.
  • Sensor malfunction or obstruction.
  • Device placed in an area with strong light interference.
  • Clean the sensor area.
  • Move the dispenser to a location without direct strong light.
  • Try turning the device off and on again.

9. Specifications

Feature Detail
Model P5
Rated Power 1.5W
Bottle Capacity 400mL
Dispensing Time (4 gears) 0.3s / 0.8s / 1.5s / 2s
Net Weight 211g (without soap)
Gross Weight 273g (without soap)
Dimensions (approx.) 187mm (H) x 107mm (W top) x 72mm (W base)
Charging USB (Type-C)
Certification CE
Origin Mainland China

10. User Tips

  • Soap Dilution: For best foaming results, always dilute your liquid soap with water. A 1:1 or 1:2 soap-to-water ratio is commonly recommended. Experiment to find the perfect consistency for your soap.
  • Battery Life: The built-in battery is designed for long-lasting performance. Users have reported battery life of 2-3 years with regular use.
  • Initial Use: After filling with soap, it might take a few dispenses for the foam to come out consistently as the pump primes.
  • Placement: Avoid placing the dispenser in direct sunlight or areas with strong artificial light, as this can interfere with the infrared sensor.

11. Warranty and Support

This product is covered by a standard manufacturer's warranty against defects in materials and workmanship. For warranty claims or technical support, please contact the retailer or manufacturer directly. Please have your purchase receipt and product model number (P5) ready when contacting support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.