1. Introduction
This manual provides detailed instructions for the installation, operation, and troubleshooting of the Wenzhi ZigBee/WiFi 5.8G/24G MmWave Radar Human Presence Motion Sensor. This smart sensor is designed for home automation, offering precise human presence and micro-motion detection, luminance sensing, and an integrated 16A relay for controlling connected devices.
2. Specifications
The WZ35 sensor comes in various configurations (ZigBee/WiFi, 5.8G/24G) and form factors (circular/ceiling-mounted). Key specifications are detailed below:
2.1. General Parameters
| Parameter | Description |
|---|---|
| Model (ZigBee) | MTG035-ZB-RL (Circular), MTG235-ZB-RL (Ceiling/Wall) |
| Model (Wi-Fi) | MTG036-WF-RL (Circular), MTG236-WF-RL (Ceiling/Wall) |
| Size (Circular) | 75mm*61mm (2.95in*2.4in) |
| Size (Ceiling/Wall) | 105mm*28mm (4.13in*1.1in) |
| Color | White |
| Weight | Approx. 120g (with packaging and accessories) |
| Beam Angle (Circular) | 110°x110° |
| Beam Angle (Ceiling/Wall) | 115°x115° |
| Sensor Sensitivity | 0-9 (Default 7) |
| Ceiling Installation Height | Typical height: 2.7-3.5 m |
| Sense Distance | 0-10m (Default 6m) |
| Departure Delay | 0.5s-1500s (Default 15s) |
| Beam (Luminance) | 0-500 Lux |
| System Frequency (5.8GHz) | 5.8 GHz ±75 MHz ISM wave |
| System Frequency (24GHz) | 24GHz ±125 MHz ISM wave |
| Transmitting Power (5.8GHz) | 3-5 dBm |
| Transmitting Power (24GHz) | 10dBm |
| Network | ZigBee3.0 / Wi-Fi (2.4GHz) / BLE |
| Input | AC85-265V |
| Power Consumption | <2W |
| Working Temperature | -10°C to +50°C |
| Storage Temperature | -20°C to +65°C |
| Working Humidity | 5-90% RH (No Condensation) |
| Working Altitude | 0-3500m |
| Relay Load (Circular) | Resistive loads 1000W / LED ≤300W |
| Relay Load (Ceiling/Wall) | Resistive loads 3000W / LED ≤300W |
| Certification | CE, RoHS |
| Origin | Mainland China |
2.2. Detection Range (Ceiling Mounted)
The sensor can detect micro movements (e.g., tilting head, waving, lifting hand, gentle movements, flipping book) and presence (standing still, squatting, sitting still). The detection range varies slightly based on the frequency band:
- 5.8G Radar Module: Presence Detection Radius: 2.5-3m, Motion Detection Radius: 4-5.5m.
- 24G Radar Module: Presence Detection Radius: 2-3m, Motion Detection Radius: 4-4.5m.
Note: Detection distance is not absolute and has a resolution of approximately 1m. The distance value is primarily used for filtering through materials like glass, gypsum board, and wood, not as a strict detection area.
3. Setup
3.1. Installation Method
The sensor can be installed using expansion screws for ceiling/wall mounting or with self-adhesive backing.
- Ceiling/Wall Mounting (Expansion Screws):
- Drill a 6mm hole (H35mm) for the expansion bolt.
- Use expansion bolts and automatic screws to fix the sensor.
- Ensure proper spacing (60mm) for the fixing holes.
- Self-Adhesive Mounting:
- Apply adhesive to the back of the product.
- Stick it firmly to the ceiling or wall in the desired detection area.
3.2. Wiring Diagram
The sensor requires AC85-265V input. For models with a relay, you can connect a load (e.g., a light bulb) to the relay output.
- Input: AC85-265V
- Connections:
- Connect the Live (L) wire.
- Connect the Neutral (N) wire.
- For models with a relay, connect your load (e.g., light) to the relay output.
- If only used as a sensor (without relay functionality), only L & N need to be connected.
3.3. App Installation & Network Connection
The sensor integrates with Tuya Smart Life for smart home control.
- App Installation: Search for "Tuya" or "Smart Life" in your app store, or scan the QR code provided in the product packaging for download. Register and log in to the app.
- Network Connection:
- Power on the sensor. The red and blue indicator lights will briefly illuminate, then turn off.
- If not connected to a network, the sensor will automatically enter a continuous network connection state for 2 minutes, indicated by the blue indicator light flashing quickly (0.5 seconds per time).
- If connection fails, power cycle the device or press and hold the connect button for more than 3 seconds to re-enter network connection mode.
- Open the Smart Life/Tuya app, tap '+' in the upper right corner, and select "Add Device". Wait for the app to discover the device, then tap "Add".
- Upon successful addition, the blue indicator light will remain on for 10 seconds and then turn off.
- ZigBee Hub Requirement: The ZigBee version of the sensor requires a ZigBee hub (e.g., Tuya ZigBee hub) for network connectivity. The WiFi version does not require a separate ZigBee hub.
3.4. ZigBee2mqtt Integration (Advanced Users)
For users integrating with ZigBee2mqtt:
- Update ZigBee2mqtt to the latest version.
- If issues persist, download the JS file from the official Wenzhi GitHub repository (
https://github.com/wzwenzhi/Wenzhi-ZigBeeZmult) and configure it as per the document in the link. - It is recommended to set the "Distance report mode" to "occupation detection" to reduce information reporting.
4. Operating the Sensor
The sensor's parameters can be configured via the Tuya Smart Life app.
4.1. Device Management Interface
The app interface provides real-time status and control options:
- Device Status: Displays manned/unmanned status.
- Environmental Illumination (Beam): Shows approximate brightness. Note that this is not an absolute value but reflects the trend of environmental brightness.
- Relay Status (Breaker): Indicates the state of the integrated relay.
- Target Distance: Displays the detected distance.
- History Log: View detection results for human presence.
- Control Parameter Settings: Access detailed settings.
- Restore Factory Settings: Option to reset the device.
4.2. Common Parameter Settings
These settings fine-tune the sensor's detection capabilities:
- Sensitive (0-9, Default 7): Adjusts the detection threshold for object energy strength.
- Departure Delay (0-1500s, Default 15s): Configures the confirmation time after a target disappears. A longer delay reduces false positives from brief disappearances.
- Detection Range (0-10m, Default 6m): Sets the maximum distance the sensor detects.
- Entry Sensitivity (0-9, Default 7): Threshold for initial target entry, used to filter accidental contact interference.
- Entry Filter Time (0-5s, Default 0.1s): Time for filtering accidental contact interference upon initial target entry.
- Entry Distance Indentation (0-10.00m, Default 0.6m): Indents the detection distance inward to avoid false triggering from distance edge interference.
- Shield Range (0-10.00m, Default 0m): Sets the nearest distance for detection. Must be less than the Detection Range.
- Block Time (0.1-255.0s, Default 2.5s): Time after switching from manned to unmanned mode before the target can be detected again. Helps resolve interference from power ripple and radiation from external devices.
4.3. Control Parameter Settings
These settings control the sensor's behavior and relay operation:
- Status Indication (Silence/Instructions, Default Silence):
- Silence: Indicator light will not flash upon human presence detection.
- Instructions: Indicator light will flash upon human presence detection.
- Sensor (Default Turn On): Sets the radar sensor to one of four states: turn on, turn off, manned (occupied), or unmanned (unoccupied). For example, if set to manned, it will continuously report presence regardless of actual presence.
- Breaker Mode (Standard/Local/Mandatory/Not Support):
- Standard (Cloud Linkage): Relay can be remotely controlled via the app.
- Local (Automatic): If presence is detected, the relay turns on; otherwise, it turns off.
- Not Support: Disables the relay, functioning only as a sensor.
- Breaker Status (Turn On/Turn Off): In Standard (Cloud Linkage) mode, the relay can be remotely controlled to turn on/off via the app.
- Illumin Threshold (0-500.00 Lux): When in Local (Automatic) mode, the relay can be controlled based on ambient luminance. If actual luminance is below the threshold, the local mode is executed. If it exceeds the threshold, the relay remains closed regardless of presence.
5. Maintenance
To ensure optimal performance and longevity of your Wenzhi Human Presence Motion Sensor, follow these general maintenance guidelines:
- Cleaning: Gently wipe the sensor's surface with a soft, dry cloth. Avoid using abrasive cleaners, solvents, or excessive moisture, as these can damage the device.
- Placement: Ensure the sensor is not obstructed by new furniture or decorations that could interfere with its detection range.
- Firm Installation: Periodically check that the sensor is firmly fixed in its installation location to prevent false readings due to vibration.
- Software Updates: Keep the Tuya Smart Life app and any connected hubs (e.g., ZigBee hub) updated to their latest versions to benefit from performance improvements and bug fixes.
6. Troubleshooting
6.1. Common Interference Sources & Solutions
If the sensor is not performing as expected, consider the following common interference sources and their solutions:
| Interference Source | Solution |
|---|---|
| Fan: | Change the position of the fan or sensor; ensure the fan is outside the presence detection area. |
| Air Conditioning: | Ensure air swing and louver vibration are outside the sensor's detection area. |
| Rolling Shutter (Aluminum Alloy): | Set an appropriate detection range to filter out such interferences. |
| Exhaust Fan: | Avoid placing the sensor near exhaust fans or vibrating surfaces. Fix the exhaust fan to prevent ceiling vibration. |
| Strong 5.8GHz WiFi Signal: | Install WiFi router at least 3m away from the sensor in the front area. For other directions, maintain at least 1.5m distance. For top-mounted APs, maintain 1.5m distance from the sensor. |
| Air Flow (Wind): | Adjust sensor sensitivity settings. |
| Animals: | Adjust sensor sensitivity and Entry Distance Indentation settings to avoid detection. |
| Low Frequency Vibration: | Avoid direct exposure of radar signals to sound/vibration sources. Set a relatively low sensitivity and a longer Entry Filter Time. |
6.2. FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Important: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user's authority to operate the equipment.
7. User Tips
- Accuracy of Distance Measurement: While the sensor provides distance detection, some users have noted that the accuracy of measuring the exact distance to an object may not be precise. It is generally effective for presence and motion detection within the defined range.
- Overall Detection Performance: The sensor is generally praised for its impressive accuracy in detecting human presence and micro-motions.
- ZigBee vs. WiFi Versions: Remember that the ZigBee version requires a compatible ZigBee hub for operation, while the WiFi version connects directly to your home WiFi network and does not need a separate hub.
8. Warranty and Support
For detailed warranty information, technical support, and further documentation, please refer to the official user manual PDF provided by Wenzhi. You can access the PDF document at: Wenzhi Human Presence Motion Sensor User Manual (PDF).
For any specific inquiries or issues not covered in this manual, please contact Wenzhi customer support.