1. Introduction
Thank you for purchasing the Baofeng UV S22 Pro V2 Portable Two-Way Radio. This device is designed to offer high performance and stable wireless communication, featuring IP68 waterproof capabilities suitable for various environments, including maritime and shipping use. Please read this manual carefully to ensure maximum performance and safe operation of your radio.
1.1. Safety Information
The following safety precautions must be observed during the operation, service, and repair of this equipment:
- This equipment should only be serviced by qualified technicians.
- Do not modify the radio for any reason.
- Use only supplied or approved batteries and chargers.
- Do not use any portable radio with a damaged antenna. Contact with a damaged antenna may cause minor burns.
- Turn off your radio before entering any area with explosive or flammable materials.
- Do not charge your battery in a location with explosive or flammable materials.
- To avoid electromagnetic interference or compatibility conflicts, turn off your radio in areas where notices instruct you to do so.
- Turn off your radio before boarding an aircraft. Any use of a radio must comply with airline regulations or crew instructions.
- Turn off your radio before entering a blasting area.
- For vehicles with an airbag, do not place a radio in the airbag deployment area.
- Do not expose the radio to direct sunlight for extended periods or place it near heating sources.
- When transmitting with a portable radio, hold it vertically with the microphone 3 to 4 centimeters from your lips. Keep the antenna at least 2.5 centimeters from your body.
WARNING: If you wear a radio on your body, ensure the radio and its antenna are at least 2.5 centimeters away from your body when transmitting.
2. Key Features
The Baofeng UV S22 Pro V2 offers a robust set of features for reliable communication:
- IP68 Waterproof and Dustproof: Designed to withstand harsh environments, functioning even after 30 minutes in one meter of water.
- High Power Output: 10W maximum power for extended range. Tri-Power selectable (1W, 5W, 10W).
- Dual-Band Operation: Supports VHF (136-174MHz) and UHF (400-520MHz) frequencies.
- Large Channel Capacity: Up to 128 memory channels.
- Cross-Band Reception/Transmission: Enhances communication flexibility.
- Display Options: Various display modes for channel number, frequency, channel name, etc.
- CTCSS & DCS: For enhanced privacy and selective calling.
- VOX Function: Voice-operated transmission for hands-free use.
- DTMF Emergency Alarm & ANI Code: For safety and identification.
- Frequency Step: Selectable steps (2.5/5/6.25/10/12.5/20/25/50 kHz).
- Battery Saving Function: Extends battery life.
- Emergency SOS: Sound and light alarm.
- Programmable: Via PC for customized settings.
- Broadband/Narrowband: Selectable (Wide 25KHz / Narrow 12.5KHz).
- FM Radio: Commercial FM radio receiver (65 MHz - 108 MHz).
- Built-in LED Flashlight: For illumination in dark environments.
- Durable Construction: High-density shell, anti-extrusion design.
Figure 2.1: Baofeng UV S22 Pro V2 highlighting IP68 waterproof rating, 10W maximum power, and selectable 1W, 5W, or 10W output.
Figure 2.2: Visual summary of the walkie talkie's powerful and versatile features.
3. Package Contents
Upon opening the package, please verify that all items listed below are present and undamaged. If any items are missing or damaged, contact your dealer immediately.
- 1 x Portable Radio (UV-S22 PRO V2)
- 1 x Antenna
- 1 x Li-ion Battery Pack
- 1 x Li-ion Charger
- 1 x Belt Clip
- 1 x Sling/Lanyard
- 1 x User's Manual (this document)
Note: Other accessories like headsets may depend on your specific purchase options.
Figure 3.1: Included accessories with the Baofeng UV S22 Pro V2.
4. Setup and Installation
4.1. Installing the Antenna
- Align the antenna with the connector on top of the radio.
- Turn the antenna clockwise until it is securely fastened. Do not rotate by the top; hold it by its base.
Important: If using an external antenna, ensure its SWR (Standing Wave Ratio) is 1.5:1 or less to prevent damage to the transceiver's final transistors. Never transmit without an antenna.
Figure 4.1: Antenna comparison and new 360-degree free bending antenna design.
4.2. Installing the Belt Clip
Attach the belt clip to the rear of the battery compartment cover using the provided screws. Ensure it is firmly secured.
Caution: Do not use any glue to fix the screws, as solvents in glue may damage the battery casing.
4.3. Micro-Headset Installation
Plug the external micro-headset connector into the 'SP. & MIC' jack on the side of the transceiver.
4.4. Battery Installation
- Ensure the battery is aligned with the guide rails on the aluminum chassis.
- Slide the battery upwards until a "click" is heard, indicating it is locked into place.
To remove the battery: Slide the battery latch at the bottom of the radio's body in the direction indicated by the arrow. Slide the battery down 1 to 2 centimeters, then remove it. Always turn off the radio before removing the battery.
5. Battery Information and Charging
5.1. Initial Use
New batteries are shipped uncharged. Charge a new battery for 5 hours before its first use. Maximum battery capacity and performance are achieved after three full charge/discharge cycles. Recharge the battery when its power runs low.
WARNING: Only use the manufacturer-specified charger to reduce the risk of injury. Other batteries may burst, causing bodily injury or property damage. Do not dispose of batteries in fire or as household waste. Never attempt to disassemble the battery.
5.2. Battery Charging Process
Use only the charger specified by the manufacturer. The charger's LED indicator shows the charging status:
| Charging Status | LED Indication |
|---|---|
| Standby (no-load) | Red LED flashes, Green LED glows |
| Charging | Red LED solidly glows |
| Fully Charged | Green LED solidly glows |
| Error | Red LED flashes, Green LED glows |
Figure 5.1: Battery charging indicators. Red light indicates charging, Green light indicates fully charged.
5.3. Battery Tips
- Charge batteries between 5°C and 40°C. Temperatures outside this range may cause leakage or damage.
- When charging a battery attached to the radio, turn the radio off for a full charge.
- Do not interrupt the power supply or remove the battery during charging.
- Never charge a wet battery; dry it with a soft cloth first.
- Batteries will eventually wear out. Replace when operating time significantly decreases.
- Clean battery contacts with a dry cloth if dust accumulates.
5.4. Prolonging Battery Life
- In cold weather, battery performance decreases. Keep a spare battery for later use.
5.5. Battery Storage
- Fully charge the battery before long-term storage to prevent over-discharge damage.
- Recharge Li-ion batteries every 6 months during storage to avoid capacity reduction.
- Store batteries in a cool, dry place at room temperature to reduce self-discharge.
6. Parts, Controls, and Display
6.1. Radio Overview
Figure 6.1: Function Key Analysis and Radio Components.
6.2. Command/Key Definition
- Power On: Rotate the PWR/VOL Switch clockwise. You will hear a "Beep" sound, and the transceiver will report the current channel. Adjust volume by rotating the switch.
- [SOS] Emergency Alarm: Long press [SOS] to activate the alarm (green light, red light, and hand lamp flash). Press again to deactivate.
- [PTT] (Push-to-Talk): Press and hold to transmit, then speak into the microphone. Release to receive.
- SK-SIDE KEY1/[F]: Press [F] to turn FM Radio on/off.
- SK-SIDE KEY2/[M]: Press [M] to turn the flashlight on/off. Press and hold [M] to monitor the signal.
- [MENU] Key: Enter the radio menu and confirm settings. Press and hold [MENU] during power-on to switch between frequency and channel modes.
- [▲]/[▼] Keys: Press to adjust frequency up/down. Hold for fast adjustment.
- [EXIT/AB] Key: Cancel/clear/exit. In standby, switch between Channel A and B. In FM radio mode, switch between 65-75MHz and 76-108MHz bands.
6.3. LCD Display Icons
The LCD displays various icons when specific operations or features are active:
| Icon | Description |
|---|---|
| + | Frequency Shift + |
| - | Frequency Shift - |
| +- | Frequency offset direction for accessing repeaters. |
| S | Dual Watch/Dual Reception functions activated. |
| VOX | Function 'VOX' enabled. |
| R | Reverse function activated. |
| N | Wide Band selected. |
| ... | Battery Level indicator |
| Keypad lock icon | Keypad lock function activated. |
| L | Low transmit power. |
| Up/Down arrows | Operation frequency. |
| Yull | Signal Strength Level. |
| 88 | Operating channel. |
| 75/25 | Operating frequency. |
| CT | 'CTCSS' activated. |
| DCS | 'DCS' activated. |
7. Basic Operation
7.1. Radio On-Off/Volume Control
Ensure the antenna and battery are correctly installed and charged. Rotate the PWR/VOL knob clockwise to turn the radio on. Continue rotating to increase the volume. Rotate counter-clockwise to decrease volume and turn off the radio.
7.2. Transmit and Receive
Select the desired channel or enter the frequency. Press and hold the PTT button to transmit. Speak into the microphone. Release the PTT button to receive.
- LCD shows 'L' for low power, 'M' for mid power, 'H' for high power during transmission.
- Press [PTT] then [SOS] to transmit 1750Hz.
- Press [PTT] then DTMF Numbers to transmit DTMF tones.
7.3. VOX (Voice Operated Transmission)
This function allows transmission without pressing the PTT button. The radio automatically transmits when it detects your voice and stops when you finish speaking. Adjust the VOX Gain level (1-10, 10 being most sensitive) in the menu to ensure smooth transmission.
Operation:
- Press [MENU].
- Navigate to Function 4 (VOX).
- Press [MENU] again, then use [▲]/[▼] to select the desired VOX level (1-10) or OFF.
- Press [MENU] to confirm and save.
7.4. AUTOLK (Keypad Locked Automatically)
This feature provides automatic keypad locking. When enabled, the keypad will lock after 2 seconds of inactivity.
Operation:
- In standby, press [MENU] + number key 24. The screen will display "AUTOLK".
- Press [MENU] to enter, then use [▲]/[▼] to select ON or OFF.
- Press [MENU] to confirm, then [EXIT] to return to standby.
7.5. VFO/Channel Mode
To switch between VFO (Frequency) mode and Channel mode: Turn off the radio. Press [MENU] and rotate the sound knob to turn on the radio. The LCD will display either the frequency or "CH-XXX" indicating the current mode.
7.6. Selecting a Frequency or Channel
Use the [▲]/[▼] keys to select the desired frequency or channel. Hold the keys for faster selection. In VFO mode, you can also input the frequency directly using the numeric keypad.
8. Advanced Features
8.1. TDR (Dual Watch/Dual Reception)
This feature allows the radio to monitor two frequencies (A and B) simultaneously. The transceiver periodically checks for signals on the secondary frequency. If a signal is received, it will stay on that frequency until the signal disappears.
Operation:
- In standby, press [MENU] + keyboard [7TDR]. The screen will display 'TDR'.
- Press [MENU] to enter, then use [▲]/[▼] to select 'TDR' OFF or ON.
- Press [MENU] to confirm, then [EXIT] to return to standby.
8.2. DEL-CH (Delete Channel)
Operation:
- In standby, press [MENU] + [Number key 28]. The screen will display 'DEL-CH'.
- Press [MENU] to enter, then use [UP]/[DOWN] to select the channel to delete.
- Press [MENU] to confirm, then [EXIT] to return to standby.
8.3. MEM-CH (Stored In Memory Channel)
The transceiver has 128 memory channels (000 to 127). To store a frequency and its parameters:
- In standby, press [MENU] + [Number key 27]. The screen will display 'MEM-CH'.
- Press [MENU] to enter, then use [UP]/[DOWN] to select the desired channel order.
- Press [MENU] to confirm, then [EXIT] to return to standby.
A complete memory channel includes RX frequency, TX frequency, CTCSS, DCS, RF Power, Bandwidth, PTT-ID, BCL, ANI, Scan add to, and Channel Name. Other settings can be configured via keypad under VFO mode.
8.4. CTCSS/DCS Scanning
Before scanning, ensure the radio is in VFO mode and Dual Standby is off. To find the CTCSS/DCS of another radio:
- Go to MENU 11.
- Press [MENU] once, then press [*/SCAN].
- While scanning, press the PTT of the other radio. The CTCSS scanning will start automatically.
- Once the scanning stops, the matching CTCSS will be displayed. Press [MENU] to store it.
Note: The use of CTCSS or DCS does not guarantee complete confidentiality of communication.
8.5. Repeater Tail Tone
Repeaters receive on one frequency and retransmit on another. The courtesy tone indicates the repeater has received your transmission. MENU 35, 36, and 37 are helpful for repeater use. MENU 35 and 36 should generally be OFF. MENU 37 (Repeater Tail Tone Delay) can be set from 1-10, with 5 being a good starting point.
10. Troubleshooting
| Problem | Possible Cause / Solution |
|---|---|
| The radio does not start. | The battery is low. Replace with a charged battery or charge the current one. Ensure the battery is correctly installed; remove and reattach if necessary. |
| The battery runs down quickly. | The battery life may have ended; replace with a new one. Ensure the battery is fully charged and made in full. |
| The receiving indicator LED lights but no sound from the speaker. | Volume setting is too low. Adjust the volume. Ensure CTCSS/DCS undertones match those programmed in the other transceivers in your group. |
| In "standby" mode, the transceiver transmits without pressing the "PTT". | Check the VOX level adjustment function; it may be set too sensitive. |
| Receiving communications from other user groups while communicating with your group. | Change frequency or channel. Adjust CTCSS/DCS undertones in your group. |
| Communication with other members of your group is poor or low quality. | You or your partner may be too far away or in an area with poor radio signal propagation (e.g., inside a tunnel, underground car park, mountainous areas, large metal structures). |
| When transmitting, other members of the group do not receive the communication. | Ensure CTCSS/DCS undertones match. You or your partner may be in a bad area of RF signal propagation. |
If problems persist after these checks, contact your distributor, dealer, or service center.
11. Technical Specifications
11.1. General
| Parameter | Value |
|---|---|
| Frequency Range | VHF: 136-174MHz (Rx/Tx), UHF: 400-520MHz (Rx/Tx), 65MHz-108MHz (Commercial FM radio reception) |
| Memory Channels | Up to 128 channels |
| Frequency Stability | 2.5ppm |
| Frequency Step | 2.5kHz/5kHz/6.25kHz/10kHz/12.5kHz/20kHz/25kHz |
| Antenna Impedance | 50 Ω |
| Operating Temperature | -20°C to +60°C |
| Supply Voltage | Rechargeable Lithium-Ion 7.4V/1800mAh |
| Consumption in Reception | 8000mA |
| Consumption in Transmission | ≤1.4A |
| Mode of Operation | Simplex or semi-duplex |
| Duty Cycle | 03/03/54 min. (Rx / Tx / Standby) |
| Dimensions | 132mm x 56mm x 35mm (approximate, from image) |
| Weight | 220g (approximate, from image) |
Figure 11.1: Product dimensions.
11.2. Transmitter
| Parameter | Value |
|---|---|
| RF Power | 10W (as per product title, manual states 15W but product is 10W) |
| Type of Modulation | FM |
| Emission Class | 16K0F3E/11K0F3E (W/N) |
| Maximum Deviation | ≤±5 kHz/≤±2.5 kHz (W/N) |
| Spurious Emissions | <-60 dB |
11.3. Receiver
| Parameter | Value |
|---|---|
| Receiver Sensitivity | 0.2 uV (at 12 dB SINAD) |
| Intermodulation | 60 dB |
| Audio Output | 1W |
| Spurious Radiation | ^65dB |
Note: All specifications are subject to change without notice.
12. User Tips
- Programming Software: For advanced customization, programming software is often required. Check with your seller if the programming software is included or available for download.
- Power Output: The radio is advertised as 10W. While some documentation might mention 15W, rely on the 10W specification for expected performance.
13. Warranty and Support
The device is guaranteed for a period of TWO YEARS from the date of sale to the final user. This Warranty Certificate is unique and not transferable. Product failure or any part replacement does not extend the guarantee period.
The warranty covers the replacement and free replacement of all parts defective in materials and components used in manufacturing or assembly. It does not cover faults caused by accident, improper installation, misuse, electrical shock, or claims due to deterioration in external appearance from normal use. Rechargeable batteries are considered consumables and are not covered by the warranty after 15 days from purchase.
To claim warranty, provide the completed and sealed Warranty Certificate, the original invoice clearly identifying the device and purchase date, and a description of the faults to your dealer or an Authorized Service Center.
For a detailed user manual in PDF format, you can refer to the official documentation provided by the seller. View User Manual (PDF)
14. Product Media
14.1. Durability Demonstration Video
Video 14.1: Demonstration of the walkie talkie's waterproof capabilities (submerged in water) and durability (run over by a car).
14.2. Additional Product Images