1. Safety Warnings
Please read this instruction manual carefully before installation and use.
- This device is for indoor use only.
- This device should not be exposed to dripping or splashing water or any other dangerous liquids/sources.
- This device should only be installed by adults.
- Do not install near any heat sources.
- Do not use this device with dimmers.
- Do not use this device in totally enclosed luminaires. Use this device in open luminaires only.
- If this device is much heavier than the one it replaces, the increased weight may reduce the mechanical stability of certain luminaires and lampholders, and may impair contact making and lamp retention.
- RISK OF ELECTRIC SHOCK: Use in dry locations only. Do not install this device with wet hands.
- Do not wire with power on. Always turn off the power to wire, and power on after checking and confirming that the wiring is correct.
- Do not use this electronic product abnormally. Abnormal use will reduce the performance and life of the product. In severe cases, it will damage the product and bring hidden dangers to your safety.
2. Product Overview
The QIACHIP KR2201GS is a 433MHz wireless remote control switch relay designed for controlling lights, fans, and other electrical appliances. It can be paired with various QIACHIP remote control transmitters, including wall panel switches, to provide convenient wireless control. The compact receiver unit is designed to fit into standard wiring boxes for easy integration into existing electrical systems.
3. Specifications
| Attribute | Value |
|---|---|
| Model | KR2201GS |
| Working Voltage | AC 90V-250V |
| Quiescent Current | <5MA |
| Max Current | 10A |
| Max Load Power (Resistive/Incandescent) | 2200W (AC220V) |
| Max Load Power (Inductive) | 500W (AC220V) |
| Max Load Power (Capacitive) | 200W (AC220V) |
| Max Load Power (Energy-saving/LED Lamp) | 300W (AC220V) |
| RF Frequency | 433-433.92MHz |
| Working Temperature | -30°C ~ 80°C |
| Receiving Sensitivity | >108 dbm |
| Amount of Storage Remote Controls | 25 pieces |
| Support Encoding | 1527 Learning code, 2262 fixed code |
| RF Operating Mode | ASK superheterodyne wireless reception |
| Remote Control Distance (Open Space) | >50 meters |
| Remote Control Distance (Indoor with Partition Wall) | 15 meters |
| Wall Switch Size | 86 standard size |
| Wall Panel Switch Battery | AAA batteries (2 required) |
| Material | Plastic |
| Certification | RoHS, CE, CCC |
4. Setup and Installation
4.1. Receiver Wiring Diagram
The receiver unit (KR2201GS) connects directly to your AC power supply and the load (e.g., light, fan). Ensure power is OFF before wiring.
Important: Do not install with electricity. Always ensure power is disconnected before performing any wiring.
4.2. Wall Panel Switch Installation
The wall panel switch (transmitter) is battery-powered and can be easily installed on any surface.
- Open the Panel: Pry open the panel through the small opening on the side of the switch.
- Insert Batteries: Insert 2 x AAA batteries into the designated slots.
- Apply Adhesive: Apply double-sided tape to the back of the switch.
- Attach to Wall: Attach the switch to the desired control location on the wall.
5. Operating Instructions (Wireless Remote Control Function)
The indicator light on the receiver unit will illuminate when it enters the pairing state with a remote control.
Note: RF working modes need to be implemented with QIACHIP brand remote control (transmitter) and controller (receiver / wireless remote control switch). There is no guarantee that remote controls from other brands will work properly.
5.1. Manual Switch Mode (Without Remote Control)
Press the setting button on the receiver unit once to turn it ON, and press it again to turn it OFF.
5.2. Pairing Remote Control (Learning Modes)
The receiver supports different learning modes for various control behaviors. The pairing process involves pressing the receiver's setting button a specific number of times, waiting for the indicator light to flash, and then pressing the desired button on the remote control.
5.2.1. Latch Mode Setting (Self-locking Mode)
In this mode, one press on the remote button turns the device ON, and another press turns it OFF. This mode is suitable for controlling one smart switch with one remote control button.
- Press the setting button on the receiver unit twice.
- The red indicator light on the receiver will flash and then light up continuously.
- Press the button on the remote control that you wish to pair.
- The red indicator light on the receiver will flash and then turn off. The latch mode setting is successful.
5.2.2. Toggle Mode Setting
In this mode, pressing and holding the remote button turns the device ON, and releasing it turns the device OFF.
- Click the setting button on the receiver unit once.
- Wait for the LED to light up, indicating it's in the setting state.
- Click the button (e.g., button A) on the remote control once.
- When the indicator light on the receiver flashes and goes out, the toggle mode setting is successful.
5.2.3. Jog Mode Setting
This mode allows one button to open and another to close, or a single button to control multiple smart switches. This mode requires at least two buttons on the remote control.
- Press the setting button on the receiver unit four times.
- The red indicator light on the receiver will flash and then light up continuously.
- Press the button on the remote control that needs to be paired for the ON function (e.g., button A).
- The red indicator light on the receiver will flash.
- Continue by pressing the button on the remote control that needs to be paired for the OFF function (e.g., button B).
- The red indicator light on the receiver will flash and then turn off. The jog mode setting is successful.
5.3. Reset (Clear Paired Transmitters)
To clear all paired remote control data from the receiver's memory:
- Press the receiver's learning button 8 times consecutively.
- Wait until the light stops flashing (for the old appearance version, it's the indicator light on the receiver that flashes).
- At this time, press the button on the transmitter to be paired to send out the signal.
- All paired transmitters are disabled and the receiver clears the memory.
6. Maintenance
6.1. Battery Replacement
When the remote control (wall panel switch) voltage is low, please replace the AAA batteries in time. A low battery voltage will generally shorten the remote control distance.
7. Troubleshooting
- Short Remote Distance or Failure to Operate: When using wireless electronic products, pay attention to avoiding metal masks, large electronic devices, electromagnetic fields, and other strong sources of interference. These can cause a short distance between the remote control and the receiver or lead to a failure of normal operation.
- Device Malfunction: Do not use this electronic product abnormally. Abnormal use will reduce the performance and life of the product. In severe cases, it will damage the product and bring hidden dangers to your safety.
- No Response After Pairing: Ensure the remote control batteries are not low. If the issue persists, try resetting the receiver and re-pairing the remote control.
8. User Tips
- The wall panel switches are battery-powered (typically AAA batteries). Remember to check and replace them when the remote range decreases.
- For optimal performance, ensure the receiver is installed in a location free from significant metal obstructions or strong electromagnetic interference.
- If you experience issues with pairing or control, a full reset of the receiver (pressing the learning button 8 times) and re-pairing the transmitters is often an effective solution.
9. Warranty and Support
This product comes with a 1-year warranty from the date of purchase.
For further assistance or to view the electronic manual, you may refer to the official QIACHIP website or the provided PDF manual:
For additional information, please visit: www.qiachip.com