SLMPLEFUN 2204

Contents

RF 433MHz Wireless Remote Control Switch Instruction Manual

Model: 2204

1. Product Overview

The SLMPLEFUN RF 433MHz Wireless Remote Control Switch is a versatile 4-channel relay receiver and transmitter system designed for controlling various electrical devices. It operates on AC 85V-250V and features a 433MHz frequency for reliable wireless communication up to 500 meters in open space. This system is ideal for automating garage doors, gates, lighting, motors, and other applications.

RF 433MHz Wireless Remote Control Switch with Receiver and two Transmitters

Figure 1: RF 433MHz Wireless Remote Control Switch System

1.1 Key Features

  • Wide Voltage Range: Operates on AC 85V-250V.
  • 4-Channel Control: Independently control up to four devices.
  • Long Range: Up to 500 meters in open space.
  • Signal Penetration: Designed to transmit signals through walls.
  • Multiple Operating Modes: Supports Momentary, Toggle, and Latched modes.
  • Anti-interference: Features free pairing and anti-interference technology.

1.2 Application Scenarios

This remote control system is suitable for a variety of applications, including:

  • Sliding doors
  • Garage doors
  • Courtyard gates
  • Barriers
  • Volume gates
  • Telescopic doors
  • Stage lighting
  • General lamps and motors
Various application scenarios for the remote control switch

Figure 2: Examples of product applications

Diagram showing remote control signal passing through walls

Figure 3: Signal penetration capability

2. Specifications

Attribute Value
Model Number2204+PT22624A Control system
Working VoltageAC 85V~250V
Input/Output Voltage1V-250V
Number of Channels4
Max Current10A
Max Load2200W
Quiescent Current5mA
RF Frequency433MHz
Working Temperature-30~+80 Celsius
Receiving Sensitivity-97dbm
Amount of Storage Remote Controls25 pieces
Support Encoding1527 Leaning code/2262 fixed code
RF Operating ModeASK superheterodyne wireless reception
Receiving RangeOpen space is more than 50 meters
Remote Operating ModeMomentary / Toggle/ Latched/ Delay Mode
Support APPNo
CertificationCE, RoHS

3. Product Components

3.1 Receiver Module

The receiver module features a learning button, indicator light, and connection terminals for power and controlled devices.

Detailed view of the receiver module with labeled components

Figure 4: Receiver Module Layout

Terminal Definitions:

  • N: Neutral wire input
  • L: Live wire input
  • NO: Normally Open contact
  • COM: Common contact
  • NC: Normally Closed contact

3.2 Remote Control Transmitter

The remote control features a retractable antenna, an indicator light, and four buttons (A, B, C, D) for controlling the receiver channels. It is powered by a 23A 12V battery.

Detailed view of the remote control transmitter with labeled components

Figure 5: Remote Control Transmitter Layout

Remote control showing 23A 12V battery

Figure 6: Remote Control Battery Type

4. Safety Information

Please read and understand all safety instructions before installation and operation. Failure to follow these instructions may result in electric shock, fire, or serious injury.

  • Ensure all power is disconnected before performing any wiring or maintenance.
  • Wiring should only be performed by a qualified electrician or knowledgeable individual.
  • Do not exceed the maximum current (10A) or maximum load (2200W) specified for the receiver.
  • Keep the device away from water and high humidity environments.
  • Do not attempt to repair or modify the device yourself. Contact support if issues arise.

5. Installation and Wiring

The receiver module requires proper electrical connections to function. Refer to the wiring diagrams below for common applications. Always ensure power is off before wiring.

Wiring diagrams for AC device, DC motor, DC device, and AC motor

Figure 7: Detailed Wiring Diagrams

General Wiring Steps:

  1. Identify the Live (L) and Neutral (N) wires from your power source (AC 85V-250V).
  2. Connect the Live (L) and Neutral (N) wires to the corresponding L and N terminals on the receiver module.
  3. For the device you wish to control (e.g., light, motor), connect its power input to the NO (Normally Open) or NC (Normally Closed) and COM (Common) terminals of the desired relay channel on the receiver.
  4. Ensure all connections are secure and insulated.

For specific wiring scenarios, please consult the detailed diagrams in Figure 7. The video below also demonstrates a wiring setup.

Video 1: Product demonstration and wiring example with a linear actuator and light.

6. Pairing and Operating Modes

The receiver supports three operating modes: Momentary, Toggle, and Latched. You must pair the remote control with the receiver in the desired mode.

6.1 Momentary Mode (Jog Mode)

In Momentary mode, the relay is active only while the remote button is pressed. It deactivates when the button is released.

Setup:

  1. Press the learning button on the receiver 1 time. The indicator light will turn on.
  2. Wait for 3 seconds.
  3. Press the desired button (e.g., 'A') on the remote control. The receiver's indicator light will flash, confirming successful pairing.

6.2 Toggle Mode (Self-Locking Mode)

In Toggle mode, pressing the remote button once activates the relay, and pressing the same button again deactivates it.

Setup:

  1. Press the learning button on the receiver 2 times. The indicator light will turn on.
  2. Wait for 3 seconds.
  3. Press the desired button (e.g., 'A') on the remote control. The receiver's indicator light will flash, confirming successful pairing.

6.3 Latched Mode (Interlock Mode)

In Latched mode, pressing one remote button activates its corresponding relay and deactivates any other active relays on the same receiver. This is useful for applications where only one output should be active at a time (e.g., UP/DOWN for a motor).

Setup:

  1. Press the learning button on the receiver 3 times. The indicator light will turn on.
  2. Wait for 3 seconds.
  3. Press the desired button (e.g., 'A') on the remote control. The receiver's indicator light will flash, confirming successful pairing.

6.4 Resetting the Receiver

To clear all paired remote controls and reset the receiver to its default state:

  1. Press the learning button on the receiver 8 times.
  2. The indicator light will flash, confirming a successful reset.

Important Notes on Reset:

  • Always reset the receiver before changing the operating mode of a remote control.
  • After a reset, all previously paired remote controls will no longer function with this receiver until re-paired.
Diagram showing free pairing and anti-interference with multiple remotes

Figure 8: Free pairing and anti-interference capability

7. Troubleshooting

  • Remote control not working after changing mode: Ensure you have performed a full reset (8 presses of the learning button) before attempting to change the operating mode of a remote control.
  • Remote control not responding: Check the battery in the remote control. Replace the 23A 12V battery if the voltage is low to ensure strong signal transmission.
  • Poor signal reception: Slightly stretch the antenna on the receiver for better signal reception. Ensure there are no major obstructions between the remote and receiver.
  • Device not turning on/off: Verify all wiring connections are secure and correct according to the diagrams. Check the power supply to both the receiver and the controlled device.

8. User Tips

  • For optimal range, ensure the receiver's antenna is fully extended and positioned away from metal objects.
  • When controlling motors, consider using Latched mode for directional control (e.g., one button for 'Up', another for 'Down').
  • Keep spare 23A 12V batteries on hand for your remote controls.
  • Test the system thoroughly after installation and any changes to the operating mode.

9. Maintenance

  • Battery Replacement: When the remote control's signal weakens or stops responding, replace the 23A 12V battery. Open the remote control casing carefully to access the battery compartment.
  • Cleaning: Keep the receiver and remote control clean and free from dust and debris. Use a soft, dry cloth for cleaning.
  • Environment: Store and operate the device in a dry environment, away from extreme temperatures and direct sunlight.

10. Support

For further assistance or inquiries, please contact the manufacturer:

  • WhatsApp: +86 181 3880 5271 / +86 135 0227 8583
  • Email: dieseelectronic@163.com

You can also view the official user manual in PDF format: Download User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.