1. Introduction
Thank you for purchasing the AIFEN A5 Soldering Station. This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your device. Please read this manual thoroughly before use and keep it for future reference.
2. Safety Attention
When the power is on, the soldering iron tip temperature is between 100°C-450°C (212°F-842°F). Improper use may lead to fires or burns. Please strictly observe the following safety guidelines:
- Do not touch the soldering iron tip or metal areas near it.
- Do not use the soldering iron near flammable materials.
- The soldering iron tip is very hot and can cause dangerous accidents. Always turn off the power after use.
- When changing parts, turn off the machine and wait for the tip to cool down.
- This product uses rated voltage and frequency (refer to the label on the back of the machine).
- It is strictly prohibited to use this product if it is damaged, especially if the power cable is damaged.
- This product uses a three-wire grounding plug and must be inserted into a three-hole grounding socket. If an extension cord is needed, use a grounded three-wire power cord.
- Do not use the soldering iron for any work other than welding.
- Do not knock the soldering tip on the workbench to clean it, as this may seriously damage the soldering tips.
- When replacing parts, use original factory parts.
- Do not tamper with the soldering iron without proper safety precautions.
- Do not wet the soldering iron, and do not use it with wet hands.
- Ensure adequate ventilation in the work area, as smoke will be produced during welding.
- Do not harm the body when using the machine.
- Children are unaware of the dangers of electrical products. Do not use or store this station in a place accessible to children. Do not allow children to get near or touch this station.
3. Product Overview and Components
Familiarize yourself with the main components of your AIFEN A5 Soldering Station:
- Handle: The soldering iron handle, compatible with C210/C245/C115 tips.
- Temperature Display: Digital display showing the current or set temperature.
- Temperature Adjustment Buttons: Up (▲) and Down (▼) buttons to adjust temperature.
- Switch Button: Power on/off switch for the station.
- Cleaning Sponge: Used for cleaning the soldering iron tip.
- Handle Connection: Port for connecting the soldering iron handle to the main unit.
4. Setup Instructions
Follow these steps to set up your soldering station:
- Connect the Handle: Connect the soldering iron handle to the handle socket on the main unit. Ensure the power is off when connecting or disconnecting to avoid damaging the control circuit board.
- Install Heating Core/Tip: Install the required heating core and soldering tip into the handle.
- Position the Station: Place the soldering station on a stable surface and rest the handle on the handle rack.
- Connect Power: Connect the power supply cable to the station and then to a grounded power outlet.
- Power On: Turn on the power switch. The display window will show "---", indicating the station is in standby mode.
5. Operating Instructions
5.1. Temperature Setting
- Increasing Temperature: Press the ▲ button once to increase the set temperature by 1°C. The display will show the set temperature. If you press and hold the ▲ button for at least one second, the temperature will rise rapidly until the button is released at the target temperature.
- Decreasing Temperature: Press the ▼ button once to decrease the set temperature by 1°C. The display will show the set temperature. If you press and hold the ▼ button for at least one second, the temperature will fall rapidly until the button is released at the target temperature.
5.2. Celsius and Fahrenheit Conversion
To switch between Celsius and Fahrenheit display modes:
- While the unit is powered off, press and hold the ▲ temperature adjustment button.
- Turn on the power switch while holding the ▲ button. The display will switch between Celsius and Fahrenheit.
5.3. Temperature Calibration
To calibrate the temperature:
- While the unit is powered off, press and hold both the ▲ and ▼ temperature adjustment buttons simultaneously.
- Turn on the power switch while holding the buttons. This will enter the ±99 degree temperature calibration interface.
- Use the ▲ or ▼ button to adjust the calibration value.
- The setting will automatically save and exit after 3 seconds of inactivity.
5.4. Standby Temperature Setting
To set the standby temperature:
- While the unit is powered off, press and hold the ▼ button.
- Turn on the power switch while holding the ▼ button. This will enter the standby temperature setting interface.
- Available standby temperatures are 0°C, 150°C, 180°C, 200°C. Setting to 0°C will turn off the standby temperature (full cooling).
- The setting will automatically save and exit after 3 seconds of inactivity.
5.5. Handle Control Operation (Wire-Controlled Version Only)
For the wire-controlled version of the A5, the handle offers additional functions:
- Handle Temperature Adjustment: In working state, press the temperature adjustment buttons on the handle to increase/decrease the temperature.
- Handle Control Machine Switch: In working state, press and hold both temperature adjustment buttons on the handle simultaneously to turn on/off the interface of the host.
Note: These handle control functions are only available on the wire-controlled version of the A5. The standard version does not include these features.
6. Maintenance
6.1. Soldering Iron Tip Temperature
High temperatures can weaken the tip's function. Choose the lowest possible temperature that allows for effective soldering. This tip has excellent temperature recovery, allowing for full welding at lower temperatures, which protects temperature-sensitive components.
6.2. Cleaning the Soldering Iron Tip
- Regular Cleaning: Use a clean sponge or copper wire cleaning ball to clean the tip regularly. After welding, residual flux can oxidize and carbonize, damaging the tip, causing welding errors, or reducing heat conduction.
- Cleaning When Not in Use: If the iron is not in use, do not leave it at high temperature for extended periods. This can cause the solder on the tip to oxidize, significantly decreasing its heat conduction.
- After Use: After use, clean the tip of the soldering iron and coat it with a new tin layer to prevent oxidation.
6.3. Checking and Cleaning the Soldering Iron Tip
Note: Do not use a file to remove oxide from the iron tip.
- Set the temperature to 250°C (482°F).
- Once the temperature is stable, clean the tip with a cleaning sponge and check its condition.
- If the tinned part of the soldering iron contains black oxide, coat the soldering iron with a new tin layer, then wipe it with a clean sponge until the oxide is completely removed. Re-coat with a new tin layer.
- If the tip is deformed or shows heavy rust, it must be replaced.
6.4. Heating Core Replacement
This soldering station uses a heating core integrated with the soldering head. To replace it, simply power off the station, allow it to cool, then directly unplug the old heating core and plug in the new one.
7. Specifications
| Feature | Specification |
|---|---|
| Brand Name | AIFEN |
| Model Number | A5 |
| Origin | Mainland China |
| Certification | CE |
| Input Voltage | AC100-240V 50/60Hz |
| Power | 120W |
| Max Power | 160W |
| Temperature Control Range | 100°C-450°C (212°F-842°F) |
| Compatible Tips | JBC C115, C210, C245 series |
| Package Dimensions (approx.) | 20cm (L) x 19cm (W) x 16cm (H) |
| Package Weight (approx.) | 0.928 kg |
8. Troubleshooting
If you encounter issues with your AIFEN A5 Soldering Station, consider the following:
- No Power: Ensure the power cable is securely connected and the power switch is on. Check the power outlet.
- Temperature Not Reaching Set Point: Verify the heating core is correctly installed. Ensure the tip is clean and properly tinned.
- Inaccurate Temperature Reading: Perform a temperature calibration as described in section 5.3.
- Poor Soldering Performance: Clean the soldering tip thoroughly. Replace the tip or heating core if it is worn, deformed, or heavily oxidized. Ensure you are using the correct tip for the application.
- Handle Control Not Working (Wire-Controlled Version): Ensure the handle is properly connected. Confirm you have the wire-controlled version, as standard versions do not support these functions.
For persistent issues, please refer to the official user manual PDF for more detailed troubleshooting or contact customer support.
9. User Tips
Based on user experiences, here are some helpful tips for using your AIFEN A5 Soldering Station:
- The temperature calibration feature is highly accurate and can be used to fine-tune your soldering experience.
- Utilize the standby temperature 'OFF' setting to allow the soldering iron to cool completely when not in active use, conserving tip life.
- Appreciate the fast heat-up time; the station can reach operating temperature in as little as 4 seconds.
- The automatic temperature control and power-off when the iron is returned to its stand are convenient features for safety and efficiency.
- The station's compatibility with various JBC tip holders (C115, C210, C245) allows for versatility across different soldering tasks.
10. Frequently Asked Questions (FAQ)
- Q: Is the AIFEN A5 Soldering Station compatible with C115 tips?
- A: Yes, the AIFEN A5 Soldering Station is compatible with JBC C115, C210, and C245 series soldering iron tips.
11. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the documentation provided with your purchase or contact the seller directly. Keep your proof of purchase for warranty claims.
A detailed user manual in PDF format is available for download. You can find it by searching for "AIFEN A5 User Manual PDF" or by checking the product page where you made your purchase. The direct link provided by the seller is: AIFEN A5 User Manual (PDF).