KuWFi WR-2F0, WR-2F1

Contents

KuWFi 300Mbps Outdoor Wireless Bridge User Manual

Model: WR-2F0, WR-2F1

Brand: KuWFi

Introduction

This manual provides comprehensive instructions for the setup, operation, maintenance, and troubleshooting of your KuWFi 300Mbps Outdoor Wireless Bridge. This device is designed for long-distance wireless transmission, supporting point-to-point and point-to-multipoint modes, and is suitable for various outdoor environments due to its robust, waterproof, and dustproof design.

KuWFi Outdoor Wireless Bridge showing point-to-point connection up to 1KM, 2.4G, 300Mbps

Figure 1: KuWFi Outdoor Wireless Bridge highlighting its point-to-point capability up to 1KM, 2.4G frequency, and 300Mbps speed.

Main Features:

  • Long-distance 2.4G/5.8G wireless transmission.
  • Supports point-to-point and point-to-multipoint modes.
  • Built-in 12dBi directional antenna for transmission distances of 1-5 km (barrier-free).
  • High-speed Wi-Fi network with maximum rates of 300Mbps (2.4GHz) and 900Mbps (5.8GHz).
  • Equipped with RJ45 WAN/LAN 10/100Mbps Ports.
  • Supports 24V PoE power supply and DC 12V power supply.
  • One-click fast pairing for easy setup between bridges.
  • Supports AP (Access Point) and Repeater functions.
  • IP65 rated dustproof and waterproof shell, designed for all-weather outdoor use with sunscreen and lightning protection.

Package Contents

The standard package includes the following items:

  • KuWFi Wireless Bridge Unit(s) (Model WR-2F0 or WR-2F1)
  • PoE Adapters
  • Ethernet Cable(s)
  • Quick Setup Manual (this document)

Video 1: Product unboxing and overview, showing the contents of the package including the bridge units, PoE adapters, and Ethernet cables.

Product Overview

Physical Appearance and Interfaces

The KuWFi Wireless Bridge features a compact, weather-resistant design. Key interfaces and indicators are located on the device for easy setup and monitoring.

Side view of KuWFi Wireless Bridge showing LED indicators and ports

Figure 2: Side view of the KuWFi Wireless Bridge, illustrating the LED indicators for Signal Strength, WiFi, LAN, WAN/POE, and Power, along with the physical ports.

LED Indicators:

  • Signal Strength: Indicates the strength of the wireless signal.
  • WiFi Signal: Lights up when WiFi is active.
  • LAN: Indicates activity on the LAN port.
  • WAN/POE: Indicates activity on the WAN/POE port and power over Ethernet status.
  • Power: Indicates the device is powered on.

Ports:

  • WAN/POE Port: Used for connecting to the network and receiving power via PoE.
  • LAN Port: Used for connecting to local network devices.
  • DC 12V Power Input: Alternative power input.

Buttons:

  • RST Button: Used for one-click pairing and factory reset.
  • M/S Switch Button: Used to select AP / Repeater mode.

Setup Instructions

1. Hardware Connection

Connect the CPE (Customer Premises Equipment) unit to your PC using an RJ45 Ethernet cable via the LAN port. Power the device using the provided PoE adapter or a DC 12V power supply.

Diagram showing Master and Slave Bridge connections

Figure 3: Master/Slave Bridge Mode connection diagram. The Master Bridge connects to a DVR or Switch via a PoE adapter and LAN cable. The Slave Bridge connects to an IP Camera via a PoE adapter and LAN cable.

2. PC IP Configuration for Web UI Access

To access the device's Web User Interface (WebUI), you need to configure your PC's IP address to be in the same subnet as the CPE. The default IP address for the CPE is 192.168.188.253.

  1. Find your network connection (e.g., Ethernet) in your PC's network settings and right-click on "Properties".
  2. Double-click on "Internet Protocol Version 4 (TCP/IPv4)".
  3. Select "Use the following IP address".
  4. Enter an IP address within the range 192.168.188.11 to 192.168.188.200 (e.g., 192.168.188.200).
  5. Set the Subnet mask to 255.255.255.0.
  6. Leave the Default gateway and DNS server fields blank or set them to the CPE's IP (192.168.188.253) if needed for internet access through the bridge.
  7. Click "OK" to save the settings.

Important: Ensure your PC's IP address is not the same as the CPE's default IP (192.168.188.253).

3. One-click Fast Pairing

The KuWFi Wireless Bridge supports quick pairing for both point-to-point and point-to-multipoint configurations.

Diagram illustrating the easy pairing process for Master and Slave Bridges

Figure 4: Easy pairing process. The image shows the RST button location on both Master and Slave Bridges, indicating a one-second press for pairing.

Point-to-Point Pairing:

  1. Designate one bridge as the "Master Router" and the other as the "Slave Router".
  2. On the Master Router, press and hold the RST key for 1 to 3 seconds, then release it.
  3. Within one minute, on the Slave Router, press and hold the RST key for 1 to 3 seconds, then release it.
  4. Wait approximately 1 to 2 minutes. The two bridges will successfully pair.

Point-to-Multipoint Pairing:

  1. Designate one bridge as the "Master Router".
  2. On the Master Router, press and hold the RST key for 1 to 3 seconds, then release it.
  3. Within one minute, on each additional Slave Router you wish to add, press and hold the RST key for 1 to 3 seconds, then release it.
  4. Wait approximately 2 minutes. Each new Slave Router will be successfully added to the network.

Operating Modes

The KuWFi Wireless Bridge supports various operating modes to suit different network requirements:

  • AP Mode (Access Point): The device acts as a central hub for wireless clients to connect to.
  • Repeater Mode: The device extends the range of an existing wireless network.
  • Bridge Mode (Point-to-Point/Multipoint): Creates a wireless link between two or more locations, effectively extending a wired network wirelessly.

You can switch between AP and Repeater modes using the M/S switch button on the device, or configure modes via the WebUI.

Web UI Management

The WebUI allows for advanced configuration and monitoring of your KuWFi Wireless Bridge.

1. Login to WebUI

  1. Ensure your PC's IP is configured correctly (as described in Setup Instructions).
  2. Open a web browser (e.g., Chrome, Firefox).
  3. In the address bar, type the default IP address of the CPE: 192.168.188.253 and press Enter.
  4. When prompted, enter the default password: admin.

2. Check CPE Bridge Information

After logging in, navigate to the 'CPE' section. Here you can view connection information for connected devices, including their mode, MAC address, IP address, signal strength, and status.

3. Wireless Bridge Settings

This section allows you to customize the wireless network settings:

  • SSID: Change the name of your wireless network.
  • Password: Set or change the Wi-Fi password.
  • Timing Management: Enable or disable the Wi-Fi signal based on a schedule (only configurable on the Master Bridge).

4. LAN Port Network Setting

Configure the network settings for the LAN port:

  • Static IP: Assign a fixed IP address to the device.
  • Get IP From Gateway: Obtain an IP address automatically from a gateway.
  • DHCP: Enable DHCP to automatically assign IP addresses to connected devices.

5. Firmware Configuration

The firmware section provides options for managing the device's software:

  • Restore: Revert to a previous firmware version.
  • Backup: Save the current firmware configuration.
  • Reset: Perform a software reset of the device.

6. Slave Bridge Information

After successful pairing, log in to the WebUI of a Slave Bridge to view its current signal strength and link quality in the 'Home' section.

7. Wireless Bridge Work Log

The firmware provides a detailed work log, which can be useful for diagnosing issues and monitoring device activity.

Application Scenarios

The KuWFi Outdoor Wireless Bridge is versatile and can be deployed in various environments to extend network connectivity.

KuWFi Outdoor Wireless Bridge showing waterproof, dustproof, and lightning protection features with operating and storage temperatures

Figure 5: Environmental resilience of the KuWFi Outdoor Wireless Bridge, highlighting its waterproof, dustproof, and lightning protection, along with its operating temperature range of -20°C to 50°C and storage temperature range of -40°C to 70°C.

Common applications include:

  • Outdoor Surveillance: Connecting IP cameras over long distances in areas like ports, factories, or large properties.
  • Rural Connectivity: Providing internet access to remote farms, villas, or mountain areas.
  • Campus/Industrial Parks: Extending network coverage across large outdoor spaces.
  • Point-to-Point/Multipoint Links: Creating stable wireless backhauls for various networking needs.

Specifications

FeatureSpecification
Brand NameKuWFi
ModelWR-2F0, WR-2F1
TypeWireless Bridge / AP / Repeater
Wi-Fi Transmission Standard802.11b/g/n
Wi-Fi Supported Frequency2.4G, 5.8G
2.4G Wi-Fi Transmission Rate300 Mbps
5G Wi-Fi Transmission Rate900 Mbps
Max. LAN Data Rate300Mbps
Wired Transfer Rate100Mbps
WAN Ports1 x 10/100Mbps (Support 24V POE)
LAN Ports1 x 10/100Mbps
Antenna TypeBuilt-in 12dBi directional antenna
Transmission Distance1-5 km (Barrier-Free)
Power Supply24V POE, DC 12V
IP GradeIP65 Outdoor Waterproof
Operating Temperature-20°C to 55°C
Storage Temperature-40°C to 70°C
Humidity5% to 95% (Non-Condensing)
Supports WPSNo
Supports WDSNo
Supports MeshYes
CertificationCE
Size168mm*86mm*39mm
Max Power Consumption< 5W

Troubleshooting

  • Difficulty with Pairing: If the devices fail to pair, ensure you are pressing the RST button for the correct duration (1-3 seconds) on both Master and Slave units within the specified timeframes. If issues persist, try resetting both devices to factory defaults (long press RST for 10 seconds) and repeat the pairing process.
  • No Internet Connection After Pairing: If the bridge link is established but you cannot access the internet, verify your network configuration. Check the LAN Port Network Setting in the WebUI to ensure correct IP address assignment (DHCP, Static IP, or Get IP From Gateway) and proper connection to your main router/network. Ensure DNS settings are correct.
  • Device Disconnects/Needs Restart: If the device frequently disconnects or requires restarts, check the power supply and cable connections. Ensure the device is within its specified operating temperature range. Consider updating the firmware if available.
  • WebUI Access Issues: If you cannot access the WebUI at 192.168.188.253, double-check your PC's IP address configuration to ensure it's in the same subnet (e.g., 192.168.188.200 with subnet mask 255.255.255.0) and not conflicting with the CPE's IP.
  • Does it work with Starlink? The device acts as a wireless bridge/extender. If your Starlink system provides an Ethernet output, this device can connect to it and extend the network wirelessly. Ensure proper network configuration.

User Tips

  • For optimal performance, ensure a clear line of sight between the two bridge units, especially for long-distance connections.
  • When setting up, some users find it helpful to configure one unit as the Master and then connect the Slave units one by one.
  • If experiencing setup difficulties, a factory reset (long press RST for 10 seconds) can often resolve configuration issues.
  • The device has been reported to work effectively over distances of 60 meters without problems.

Warranty and Support

For detailed warranty information and technical support, please refer to the official KuWFi website or contact your retailer. Keep your purchase receipt as proof of purchase.

A PDF version of the user manual is available for download: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.