BAOFENG UV-20

Contents

Baofeng UV-20 Dual Band Walkie Talkie User Manual

Model: UV-20 Series

1. Introduction

This manual provides comprehensive instructions for the safe and efficient operation of your Baofeng UV-20 Dual Band Walkie Talkie. Please read this manual thoroughly before using the device to ensure proper functionality and to prevent damage or injury.

1.1 Regulations and Safety Warnings

EU Regulatory Conformance: The product complies with essential requirements of Directive 2014/53/EU and other relevant provisions (2006/66/EC, 2011/65/EU, (EU)2015/863, 2012/19/EU). Operation is permitted under 2000m. European Users must hold a valid Amateur Radio License for operation in Transmit mode. Failure to comply may result in legal action. This information is applicable to EU countries only.

Compliance with RF Exposure Standards: The radio complies with RF energy exposure standards and guidelines from United States Federal Communications Commission (47 CFR § 1.1307, 1.1310, 2.1093), American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005, and Canada RSS102 Issue 5 March 2015.

RF Exposure Compliance and Control Guidelines:

  • Do not remove the RF Exposure Label from the device.
  • User awareness instructions should accompany the device when transferred to other users.
  • Do not use this device if operational requirements are not met.
  • Transmit no more than 50% of the time. Press the Push-to-Talk (PTT) key to transmit, release to receive.
  • Keep the radio unit at least 2.5cm away from the face.
  • When worn on the body, always place the radio in an approved holder, holster, case, body harness, or use the correct clip.
  • Use of non-approved antennas, batteries, and accessories may cause the radio to exceed FCC RF exposure guidelines.
  • Contact your local dealer for optional accessories.

Precautions for Portable Terminals (Operating Prohibitions):

  1. Do not operate in locations with fuels, chemicals, explosive atmospheres, or other flammable/explosive materials.
  2. Do not operate near or in any blasting area.
  3. Do not operate near medical or electronic equipment vulnerable to RF signals.
  4. Do not hold the product while driving.
  5. Do not operate in areas where wireless communication equipment is prohibited.

Important Tips:

  1. Do not use unauthorized or damaged accessories.
  2. Keep the product at least 2.5 centimeters away from your body during transmission.
  3. Do not keep the product receiving at high volume for a long time.
  4. For vehicles with an airbag, do not place the product over the airbag or in the airbag deployment area.
  5. Keep the product and its accessories out of reach of children and pets.
  6. Operate the product within the specified temperature range.
  7. Continuous transmission may lead to heat accumulation; allow for proper cooling.
  8. Handle the product with care.
  9. Do not disassemble, modify, or repair the product and its accessories without authorization.

2. Setup

2.1 Content of the Packaging

Your Baofeng UV-20 package should contain the following items:

  • Radio body
  • Type-C USB Charger
  • Antenna
  • Li-Ion battery pack
  • Wall adaptor
  • Belt clip

If any item is missing, please verify with your dealer.

Package contents of the Baofeng UV-20 radio
Figure 2.1: Package contents of the Baofeng UV-20 radio, including radio, battery, antenna, back clip, lanyard, charger cable, adapter, and manual.

2.2 Installing / Removing the Battery

Installing the Battery Pack:

  1. Position the battery pack over the back of the radio.
  2. Engage the battery pack into the radio until it is fully seated into the radio housing.
  3. Tighten the screws using a coin or object to secure the battery pack. Do not overtighten.

Removing Battery Pack from Radio:

  1. Loosen the screws on the back of the battery pack.
  2. Lift the bottom of the battery pack slightly to remove it from the radio housing.
  3. Pull the battery pack out of the radio housing.

NOTE: The Li-ON battery pack can also be charged in the battery charger.

2.3 Installing / Removing the Antenna

Installing the Antenna:

Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure.

Removing the Antenna:

Turn the antenna counter-clockwise to remove it.

2.4 Installing / Removing the Belt Clip

Installing the Belt Clip:

Place the belt clip above the corresponding holes on the back of the radio, and screw it into place clockwise with the two supplied screws.

Removing the Belt Clip:

Unscrew counter-clockwise to remove the belt clip.

2.5 Installing Additional Speaker/Microphone (Optional)

Pry open the rubber MIC-Headset jack cover and then insert the Speaker / Microphone plug into the double jack.

2.6 Radio Overview - Components and Controls

Labeled diagram of the Baofeng UV-20 radio's buttons and components
Figure 2.2: Labeled diagram of the Baofeng UV-20 radio's buttons and components, including Antenna, Color LCD, MENU Key, Keypad, Speaker, EXIT Key, Power/Volume, Pilot lamp, MIC/SP, Lamp switch, PTT Key.

The main components and controls are:

  1. Antenna
  2. Flashlight/Emergency Alert key
  3. PTT key
  4. FM broadcast/Monitor key
  5. Power/Volume knob
  6. LED flashlight
  7. Color LCD
  8. MENU key
  9. Numeric keypad and speaker
  10. MIC Input
  11. EXIT Key
  12. Up/Down navigation keys
  13. LED Status Indicator
  14. Speaker/Mic Jacks
  15. Type-C charging indicator
  16. Type-C charging port
  17. Battery tightening screw
Product dimensions of the Baofeng UV-20 radio
Figure 2.3: Product dimensions of the Baofeng UV-20 radio: 12.2cm height, 5.7cm width, 3.5cm depth (not including antenna).

3. Operating Instructions

3.1 Power On/Off and Volume Adjustment

Powering On the Radio:

Rotate the Volume/Power knob clockwise until you hear a "click". The display will show a message or flash, followed by a frequency or channel. If voice prompt is enabled, it will announce "frequency mode" or "channel mode".

Powering Off the Radio:

Turn the Volume/Power knob counter-clockwise all the way until you hear a "click".

Adjusting the Volume:

Turn the Volume/Power knob clockwise to increase volume, counter-clockwise to decrease. Be careful not to turn it too far counter-clockwise, as you may inadvertently turn the radio off.

3.2 Basic Operations

Main Band/Sub Band Switch:

Press the [EXIT] key to switch the main channel to the other channel if two channels are displayed. The channel indicated by the arrow is the main channel.

VFO/Channel Switch:

Press and hold the [MENU] key to switch between VFO (Frequency) and Channel (MR) display modes. In channel mode, the channel number is displayed. In frequency mode, 'VFO' is displayed.

Frequency (VFO) Mode:

Navigate up and down the band using the ▲ or ▼ keys. Each press increments or decrements the frequency by the set step. Frequencies can also be input directly via the numeric keypad.

WARNING! Transmitting on unauthorized frequencies is illegal. Always verify authorization before transmitting.

3.3 Channel (MR) Mode and Channel Selection

The radio operates in two modes: Frequency (VFO) mode for experimentation and programming, and Channel (MR) mode for everyday use. In Channel (MR) mode, navigate channels using the ▲ or ▼ keys or the encoder. Press and hold [MENU] to switch between VFO and Channel mode.

Channel Selection:

  1. Use the ▲ or ▼ navigation key to select the channel.
  2. Input channel numbers directly via the keyboard (e.g., [0][1][2] for channel 12).

If voice prompt is enabled, the channel will be broadcast by voice.

3.4 Making a Call

NOTE: Press [EXIT] to switch the main channel if two are displayed. In standby, press and hold [MENU] to switch between VFO and MR mode.

Channel Mode Call:

After selecting a channel, hold down the [PTT] key to initiate a call. Speak into the microphone with a normal tone. The red LED will illuminate during transmission.

Frequency Mode Call:

Press and hold [MENU] to switch to frequency mode, then input the working frequency.

Receiving a Call:

When you release the [PTT] key, you can answer without any action. The green LED will illuminate when receiving a call.

NOTE: For best reception, keep the microphone 2.5 cm to 5 cm from your mouth during transmission.

3.5 Special Functions

Using the Flashlight:

Press the Flashlight icon key to turn on the high-intensity LED flashlight. Press once for continuous on, a second time for strobe emergency mode, and a third time to turn off.

Baofeng UV-20 radio used as a high brightness flashlight
Figure 3.1: The Baofeng UV-20 radio features a high brightness flashlight, useful for outdoor activities in dark environments.

Emergency Alert:

Press and hold the Emergency Alert icon key for 3 seconds to activate. The radio will emit a loud siren and the flashlight will flash. Press the Emergency Alert icon key to exit. WARNING: Use only in actual emergencies.

FM Radio (FM):

Listen to FM radio on frequencies 65-108MHz. Press [MENU] to switch between 65-75 MHz and 76-108 MHz bands. Press #z to automatically search for stations. Press [FM broadcast/Monitor] to exit FM radio.

Baofeng UV-20 radio displaying FM radio frequency
Figure 3.2: The Baofeng UV-20 features a 1.77" color large screen, displaying FM radio frequencies.

Monitor:

In standby, press [FM broadcast/Monitor] to enter Monitor mode. This allows monitoring weak signals. Press again to exit. If no signal is present, it will emit noise.

Keypad Lock:

Locks all keys except the three side keys. Press and hold Keypad lock icon for about two seconds to enable/disable. Can also be set to auto-lock after ten seconds via the menu.

Frequency Reversal:

A short press of the Frequency reversal icon key enables reverse function, swapping transmit and receive frequencies.

TX Repeaters Tone:

Press [PTT] + TX Repeaters Tone icon key to send a 1750Hz repeater tone. This is useful for communications through repeaters. Works even with keypad lock enabled.

Weather Radio/Scan Weather Channel (NOAA):

The radio has a NOAA Weather Radio function to receive weather reports. It can also scan all 10 NOAA Weather Radio channels.

Baofeng UV-20 radio displaying NOAA weather channels
Figure 3.3: The Baofeng UV-20 supports NOAA weather reception, displaying weather channels.
To turn on NOAA Weather Scan:

Press and hold the NOAA icon key for 3 seconds. The radio will go to Weather band mode.

To start automatic scanning:

Press and hold the #z key for 3 seconds. To stop, press and hold #z again.

To manually select a weather channel:

Use the ▲ or ▼ key after stopping the scan.

To exit Weather Radio broadcast mode:

Press [EXIT] or [PTT] key.

NOTE: Weather Channels Wx 1 Thru 10 are Receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.

Weather Channel Frequencies and Names:
Channel Number RX Frequency MHz Channel Number RX Frequency MHz
CH-01162.550CH-06162.500
CH-02162.400CH-07162.525
CH-03162.475CH-08161.650
CH-04162.425CH-09161.775
CH-05162.450CH-10163.275

Scanner Function:

Built-in scanner for VHF and UHF bands. In VFO mode, it scans in steps; in Channel (MR) mode, it scans channels. To enable, press and hold #z for about two seconds. Use ▲ or ▼ to change scanning direction. Press and hold #z to exit.

Two Baofeng UV-20 radios demonstrating the Frequency Measurement Function
Figure 3.4: The Baofeng UV-20 features a one-click frequency copy function, allowing easy replication of frequencies and CTCSS from other Baofeng devices.
Frequency Range:

In frequency mode, set the sweep range by inputting start and end values via the keyboard (e.g., 144146 for 144.000-146.000MHZ).

Scan Modes:
  • Time Operation (TO): Scanner stops on signal, resumes after a preset timeout.
  • Carrier Operation (CO): Scanner stops on signal, resumes after a preset time with no signal.
  • Search Operation (SE): Scanner stops on signal. Press and hold #z to resume.

Scan Sub-Code (CTCSS/DCS):

To search for CTCSS/DCS codes, enter a known frequency in VFO mode, then use the menu to scan for sub-codes. Once found, the code can be stored. In MR or VFO mode, scanned CTCSS/DCS codes can be stored as TX or RX codes.

DTMF (Dual-Tone Multi-Frequency):

Used for in-band signaling, common in amateur radio repeaters for activation. The radio supports full DTMF implementation (A, B, C, D codes) and numerical keys correspond to DTMF codes.

DTMF Frequencies and Corresponding Codes:
1209Hz 1336Hz 1477Hz 1633Hz
697Hz123A
770Hz456B
852Hz789C
941Hz*0#D
Call With Signaling:

Refers to calls made to a target ID on a channel with preset DTMF signaling code. Configurable via CPS Programming Path >> Programming >> DTMF System >> Call Code, Call Name >> ANI ID.

DTMF Manual Dial:

Short press #z to enter DTMF manual dialing. Enter the DTMF number and hold PTT to make a call. For private calls, confirm ID with #z and hold PTT.

Dual Watch:

Allows monitoring two channels simultaneously. The radio features single-receiver Dual Watch, with the ability to lock transmit frequency to one of the two monitored channels.

Enabling/Disabling Dual Watch:
  1. Press [MENU] to enter the main menu.
  2. Enter 3 for Radio Settings.
  3. Press [MENU], enter 14 for Dual Watch.
  4. Press [MENU] to select.
  5. Use ▲ or ▼ keys to enable or disable.
  6. Press [MENU] to confirm.
  7. Press [EXIT] to return.

When enabled, the 'D' icon is displayed. To disable, select "OFF" in step 5.

Manual Programming (Channels Memory):

Memory channels store commonly used frequencies. The radio has 999 memory channels, each holding receive/transmit frequencies, transmit power, signaling info, bandwidth, ANI/PTT-ID settings, and a 6-character alphanumeric identifier.

Frequency Mode (VFO) vs. Channel Mode (MR):

VFO mode is for temporary frequency assignment or quick programming. MR mode is for selecting preprogrammed channels. Switch between modes by pressing and holding [MENU].

Programming a Channel Repeater Offset with CTCSS Tone (Example):

To program a new memory in Channel 10 (RX=432.55000 MHz, TX=437.55000 MHz (+5 Offset), TX CTCSS tone 123.0):

  1. Press [EXIT] to switch between menus.
  2. Press and hold [MENU] to set the radio to VFO mode (VFO icon displayed).
  3. [MENU] [4] [MENU] [1][7] [MENU] [1] [0] [MENU] [EXIT] (Deletes Prior Data in channel 10)
  4. [MENU] [4] [MENU] [5] [MENU] 123.0[MENU] [EXIT] (Selects desired TX encode tone 123 CTCSS)
  5. Enter RX frequency (43255000)
  6. [MENU] [4] [MENU] [1][6] [MENU] [1][0] [MENU] -->> [EXIT] (Enters the same channel 10)
  7. Press and hold [MENU] to return to MR mode.
Programming a Simplex Channel with CTCSS Tone (Example):

To program a new memory in Channel 10 (RX=432.6500 MHz, TX CTCSS tone 123.0):

  1. Press [EXIT] to switch between menus.
  2. Press and hold [MENU] to set the radio to VFO mode (VFO icon displayed).
  3. [MENU] [4] [MENU] [1][7] [MENU] [1] [0] [MENU] [EXIT] (Deletes Prior Data in channel 10)
  4. [MENU] [4] [MENU] [5] [MENU] 123.0[MENU] [EXIT] (Selects desired TX encode tone 123 CTCSS)
  5. Enter RX frequency (43265000)
  6. [MENU] [4] [MENU] [1][6] [MENU] [1][0] [MENU] -->> [EXIT] (Enters the same channel 10)
  7. Press and hold [MENU] to return to MR mode.

Repeaters Programming:

Assumes knowledge of repeater transmit/receive frequencies and authorization.

  1. Press and hold [MENU] to set transceiver to VFO mode.
  2. Use numeric keypad to enter repeater's output (receive) frequency.
  3. Press [MENU] [4] [MENU] [1][4] [MENU] to get the offset frequency.
  4. Use numeric keypad to enter the specified frequency offset.
  5. Press [MENU] to confirm and save.
  6. [MENU] [4] [MENU] [1][5] [MENU] to set offset direction (positive or negative).
  7. Use ▲ or ▼ keys to select offset direction.
  8. Press [MENU] to confirm and save.

Optional: Save to memory, set up CTCSS. Press [EXIT] to exit. If issues persist, check settings or contact support.

Amateur Radio Setup:

For amateur radio use, it's recommended to turn off commercial features for broader compatibility.

Recommended Settings:
  • Turn ANI, DTMFST, PTT-ID off and PTT-LT to 0ms (Menu items 18-20).
  • Turn off Squelch Tail Elimination (Tail) features (Menu item 23).
  • Turn roger beep (ROGER) off (Menu item 10).
  • Set bandwidth to Wide (Menu item 5).
  • Turn DCS and CTCSS off (Menu items 6-9).
  • Turn Signaling code off and SPK-Mute (Menu items 11 and 13).

3.6 Main Menu Functions

The menu allows operations like selecting Banks, setting SCAN, Radio Settings, Program Channels, and viewing Radio Information.

Basic Menu Use:

  1. Press [MENU] to enter.
  2. Use ▲ or ▼ to navigate items.
  3. Press [MENU] again to select an item.
  4. Use ▲ or ▼ to navigate parameters.
  5. Press [MENU] again to select a parameter.
  6. Use ▲ or ▼ to select the desired parameter value.
  7. Press [MENU] to confirm and save.
  8. Press [EXIT] to cancel changes and exit.
  9. Press [PTT] to exit the menu at any time.

Using Short-Cuts:

Each menu item has a numerical value for direct access.

Short-cut Access:
  1. Press [MENU].
  2. Enter the menu item number via the keypad.
  3. Press [MENU] to enter the item.
  4. For parameters, use ▲/▼ or numerical keypad for short-cut code.
  5. Confirm with [MENU] to save, or [EXIT] to cancel.
Quick Access Examples:
  • [MENU] + 1: Banks selection (up to 10 banks, 100 channels each).
  • [MENU] + 2: Scan Settings (VFO frequency range, Scan mode, Scan Sub-Code, Scan Memory).
  • [MENU] + 3: Radio settings (general radio settings).
  • [MENU] + 4: Program Channel (Alias, TX/RX Frequency, TX Power, Bandwidth, Display mode, Channel Memory, Channel delete).
  • [MENU] + 5: Radio information (ANI ID, Firmware version, Hardware version).

3.7 Radio Settings (Menu Items)

Step Frequency (MENU + 1):

Selectable steps: 2.5K, 5.0K, 6.25K, 10.0K, 12.5K, 20.0K, 25.0K, 50.0K. Not modifiable in channel mode.

Squelch Level (MENU + 2):

Adjust squelch in 5 levels. OFF detects all signals (including noise). Level 5 receives only strongest signals.

Power Save (MENU + 3):

Reduces battery consumption in standby. Turning on is more power efficient but may cut off initial syllables.

VOX Function (Vox Level) (MENU + 4):

Sets internal microphone sensitivity (Level 1-9, Default Off). Radio transmits automatically when voice gain reaches set value. Free your hands and no need to press PTT button, easy to reply.

Illustration of VOX function with a person climbing
Figure 3.5: The VOX function allows hands-free operation, automatically transmitting when voice is detected.

VOX Delay (MENU + 5):

Extends transmission time when VOX is enabled (0.5-2.0 seconds, Step 0.1 second, Default 1 second).

Time-Out-Timer (TOT) (MENU + 6):

Sets continuous transmission duration (Off, 15-180 seconds, Step 15 seconds, Default 60 seconds). Prevents single users from occupying a channel too long.

Transmission Overtime Alarm (TOA) (MENU + 7):

Sets duration before an alert is given for transmission termination (0-10 seconds, Step 1 second, Default Off).

Voice Prompts (Voice) (MENU + 8):

Activates voice prompts for operations/selections.

Language Selection (Language) (MENU + 9):

Selects LCD display and operation prompt language (Chinese, English).

Roger Beep (ROGER) (MENU + 10):

Radio beeps when PTT is released, confirming transmission end. (Default Off).

Keypad Beep (Beep) (MENU + 11):

Every key press produces a beep tone when enabled.

Backlight (Backlight) (MENU + 12):

Adjusts auto-off time of display backlight (Always On, 5S-20S adjustable). Valid when power save is off.

Power On Image (Power on Display) (MENU + 13):

Sets display mode when radio powers on: PICTURE (preset startup picture), MESSAGE (welcome message), VOLTAGE (momentary voltage display).

Dual Watch Operation (Dual Watch) (MENU + 14):

Receives frequencies of channel A and B simultaneously. If a signal is detected, the ▲ or ▼ pointer blinks. 'D' icon displayed. Parameters of A/B channels can be changed.

Auto Keypad Lock (AutoLock) (MENU + 15):

Keypad automatically locks after 10s of inactivity. Press Keypad lock icon for 2 seconds to unlock.

Alarm Mode (Alarm Mode) (MENU + 16):

Sets tone alarm/code alarm/site alarm. Keep [SK1] pressed for 3 seconds to start. Options: Site (speaker alarm, no transmit), Tone (speaker alarm, transmits), Code (speaker alarm, transmits with ANI-ID).

Local Alarm Tone (Alarm Tone) (MENU + 17):

Emits local alarm whistle when emergency alarm is triggered.

ANI-ID (ANI-ID) (MENU + 18):

Displays/allows editing of ANI code (up to 5 digits). Sent when alarm is active and menu 16 = SEND CODE. Also sent during DTMF signaling calls.

DTMFST (DTMFST) (MENU + 19):

Determines when DTMF Side Tones are heard. Options: Off, DT-ST (manual key), ANI-ST (automatic key), DT+ANI (all).

PTT-ID (PTT-ID) (MENU + 20):

Sends ANI-ID codes at beginning (BOT), end (EOT), or both (BOTH) of transmission. Off disables DTMF signaling.

Signal Code Sending Delay (PTT-DLY) (MENU + 21):

PTT-ID signal code sending delay time (100-3000ms).

1750Hz Repeater Tone (ALERT) (MENU + 22):

Selects repeater tone frequency (1000Hz, 1450Hz, 1750Hz, 2100Hz). Hold [PTT] + Alert icon to send. Works with keypad lock enabled.

Squelch Tail Elimination (TAIL) (MENU + 23):

Eliminates squelch tail noise between handhelds (no repeater). Mutes audio for 55 Hz or 134.4 Hz tone burst.

Dual Band Single Display (Single Mode) (MENU + 24):

Radio is dual-band, dual-display. Screen can display A/B frequency band. Can be set to single-screen display, showing channel nickname, frequency, and channel number.

Reset (Reset) (MENU + 25):

Resets transceiver to factory settings. Options: VFO (menu reset), ALL (menu and channel reset).

3.8 Program Channel (Menu Items)

Channel configuration modifies current channel parameters without affecting others.

Channel Name (CHNAME) (MENU + 1):

Set channel name (up to 8 characters, A-Z, 0-9). Edit with keypad, confirm with [MENU], exit with [EXIT].

RX Frequency (MENU + 2):

Input RX frequency via keypad, [MENU] to save, [EXIT] to return.

TX Frequency (MENU + 3):

Input TX frequency via keypad, [MENU] to save, [EXIT] to return.

Transmit Power (Tx Power) (MENU + 4):

Set TX power for current channel (High/Low).

Wide/Narrow Bandwidth (MENU + 5):

Select wideband (25 KHz) or narrowband (12.5 KHz).

Receiving CTCSS (Rx CTCSS) (MENU + 6):

Add CTCSS codes to channels for private communication (50 groups).

Receiving DCS (Rx DCS) (MENU + 7):

Add DCS codes to channels for private communication (208 groups).

Transmitting CTCSS (Tx CTCSS) (MENU + 8):

Set CTCSS tone in TX mode (Off or 67.0 to 254.1 Hz).

Transmitting DCS (Tx DCS) (MENU + 9):

Activate DCS codes in TX mode (Normal R-DCS or Inverted R-DCS).

Call Encryption (Encryption) (MENU + 10):

If channel is configured with CTCSS/DCS and encryption is on, communication remains private. Encryption icon displayed when active.

Signal Code (Signaling) (MENU + 11):

Selects 1 of 20 DTMF codes (up to 3 digits each).

Working Mode (CH-MDF) (MENU + 12):

Sets display mode: NAME (channel name), FREQ (frequency mode), CH (channel mode).

Monitor (SP-MUTE) (MENU + 13):

Monitor opens if QT (correct CTCSS), QT+DTMF (correct CTCSS and DTMF), or QT*DTMF (correct CTCSS or DTMF) is detected.

Scan Add (Scan Add) (MENU + 14):

In channel mode, adds current channel to scan group (On/Off).

Busy Channel Lock (Busy Lock) (MENU + 15):

Prevents transmission if channel is in use. Release PTT to transmit when channel is free.

Frequency Offset (Offset) (MENU + 14 - in frequency mode):

Sets deviation between TX and RX (00.000-99.998MHz).

Frequency Offset Direction (Direction) (MENU + 15 - in frequency mode):

Sets direction of frequency offset: OFF (no offset), Plus (+), Minus (-).

3.9 Radio Information (MENU + 5)

Displays Radio ID, firmware version, and hardware version.

Video 3.1: A product demonstration showcasing the Baofeng UV-20 radio in various colors, highlighting its physical features, FM radio scanning, and the one-click frequency copy function.

4. Maintenance

4.1 Charging the Battery Pack

The Li-ion battery pack is not charged at the factory; please charge it before use. For optimal performance, fully charge/discharge the battery two or three times before reaching its best operating capacity. Replace the battery pack if operating time decreases despite proper charging.

Charger Supplied:

Use only the specified charger provided by Baofeng to avoid explosion or injury. Charge the battery if the radio displays low battery with a red flashing lamp or voice prompt.

Use Caution with the Li-ion Battery:

  1. Do not short the battery terminals or throw the battery into a fire.
  2. Never attempt to remove the casing from the battery pack.

How to Charge:

  1. Plug the AC adaptor into the AC outlet, then plug the cable into the DC jack on the charger. The indicator light blinks orange.
  2. Plug the battery or radio into the charger. Ensure good contact. The indicator light turns red (charging).
  3. A full charge takes approximately 2-5 hours. When the lamp lights green, charging is complete. Remove the battery/radio.

NOTICE: If the radio is powered on during charging, the indicator lamp may not turn green to show full charge. Turn off the radio for normal indication. The radio consumes energy when on, affecting accurate voltage detection.

Using the Type-C Charger:

The Type-C charger provides a convenient way to charge your Li-ion battery pack.

  1. Ensure your radio is turned OFF.
  2. Plug the Type-C cable into the Type-C charging port on your battery. Connect the other end to a wall power outlet.
  3. An empty battery will be fully charged in 6 hours.
  4. The battery meter on the LCD will indicate charging progress.
Baofeng UV-20 radio with Type-C charging port and various charging methods
Figure 4.1: The Baofeng UV-20 supports Type-C charging, allowing convenient charging from various sources like car, PC, charger, or power bank.

4.2 Battery Maintenance

The battery comes uncharged; charge for 4-5 hours before first use.

  • Use only manufacturer-approved batteries.
  • Never disassemble the battery pack.
  • Do not expose batteries to fire or intense heat.
  • Dispose of batteries according to local recycling regulations.

Prolonging Battery Life:

  • Charge batteries at normal room temperatures ($5^{\circ}C-40^{\circ}C$).
  • Turn off the radio for faster charging.
  • Do not unplug power or remove battery before charging is complete.
  • Never charge a wet battery.
  • Consider a new battery if operating time significantly shortens.
  • In cold environments, keep a spare battery warm (e.g., inside jacket).
  • Wipe charging contacts with a clean, dry cloth if dusty.
  • If wet, remove from radio, wipe dry, and place in a plastic bag with dry rice overnight.

How to Store the Battery:

  • Store at 80% discharged.
  • Keep in low temperature and dry environment.
  • Keep away from hot places and direct sunlight.
  • Cycle the battery at least every six months to avoid capacity degradation.

NOTICE: Do not short circuit terminals, disassemble, store in unsafe surroundings, or expose to heat/fire.

5. Troubleshooting Guide

If you encounter issues with your radio, refer to the table below for common problems and solutions. If the problem persists, contact your dealer for technical support.

Phenomena Analysis Solution
Cannot turn on the radio. Battery improperly installed, battery run out, poor battery contact. Remove and reattach battery, recharge/replace battery, clean battery contacts.
Weak or intermittent voice during reception. Low battery voltage, low volume level, loose/incorrectly installed antenna, blocked speaker. Recharge/replace battery, increase volume, turn off radio and reattach antenna, clean speaker surface.
Cannot communicate with other group members. Inconsistent frequency/signaling type, too far from other members. Verify TX/RX frequency and signaling type, move closer to other members.
Hear unknown voices or noise. Interrupted by other radios on same frequency, radio in analog mode without signaling. Change frequency or adjust squelch level, request dealer to set signaling.
Unable to hear due to too much noise/hiss. Unfavorable position (e.g., blocked by buildings/underground), external disturbance. Move to open/flat area and restart, stay away from interfering equipment.
Radio keeps transmitting. VOX turned on, headset not installed. Turn off VOX, check headset installation.

6. Specifications

All specifications are subject to change without prior notice or liability.

6.1 General Specifications

Feature Specification
Channel Capacity1000
Channel Spacing25.0 KHz/12.5 KHz
Input Voltage7.4 VDC
Operating Temperature-10°C to 60°C
Antenna Impedance50Ω
Dimensions122*57*35mm (not included antenna)
Radio Weight300 g (with Li-ON battery)
Battery CapacityHigh Capacity (e.g., 5000 mAh as per Q&A)
Waterproof / Water-ResistantNo
Display1.77" TFT large screen
Walkie Talkie TypePortable
OriginMainland China
CertificationCE

6.2 Transmitter Specifications

Feature Specification
Frequency Range (TX)136-174MHz & 400-520MHz
Output Power (w)3w-5w
Modulation16K0F3E/11K0F3E
Spurious Emission-16 dBm<1GHz, -16 dBm>1GHz
Frequency Stability±2.5 ppm
Audio Distortion≤5%
FM Hum & Noise40 dB

6.3 Receiver Specifications

Feature Specification
Frequency Range136-174MHz & 400-520MHz (Scan Receiver)
Sensitivity: 12 dB SINAD-120 dBm
Adjacent Channel Selectivity-60 dBm
Intermodulation and Rejection-70 dBm
Rated Audio Distortion≤5%

7. User Tips

  • Range Expectations: While the product may advertise a maximum range, actual effective range can vary significantly based on terrain, obstructions, and atmospheric conditions. In urban or heavily obstructed areas, expect a practical range closer to 5-10 km rather than the theoretical maximum.
  • Battery Capacity: The battery is indeed a high-capacity Li-Ion unit, often around 5000 mAh, providing extended usage time. Always ensure it's fully charged before critical use.
  • Compatibility: The Baofeng UV-20 is an analog radio. It can connect with other analog devices from different companies as long as they operate on compatible frequencies and use the same CTCSS/DCS tones. Digital radios require specific digital protocols and are generally not compatible with analog-only devices.
  • Frequency Copy Function: Utilize the one-click frequency copy function to quickly match frequencies and tones with other Baofeng devices, simplifying setup for group communications.
  • NOAA Weather Channels: Remember that NOAA weather channels are receive-only. You cannot transmit on these frequencies.

8. Warranty and Support

8.1 Disclaimer

The accuracy and completeness of the contents of this manual are diligently sought. However, the manufacturer does not bear responsibility for possible errors or omissions. Due to continuous technological development, the design and specifications of the product may change without notice. No part of this handbook may be reproduced, modified, translated, or disseminated without prior written authorization.

8.2 Manufacturer Information

Fujian Baofeng Electronics Co.,Ltd.
ADD: Changfu Industrial Bank Xiamei, Nan'an, Quanzhou, Fujian, China

Print version: HD-UV20_EN V1.0


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.