HTBCCHB 3.00-19

Contents

Motorcycle Inner Tube User Manual

Brand: HTBCCHB | Model: 3.00-19

1. Product Information

This manual provides essential information for the safe and effective use of your HTBCCHB Motorcycle Inner Tube. Please read it thoroughly before installation and use.

HTBCCHB 3.00-19 Motorcycle Inner Tube
Figure 1: HTBCCHB 3.00-19 Motorcycle Inner Tube

This product is a safety accessory for vehicle tires, designed for 150cc-250cc PIT Trail Dirt Bikes and Off-Road motorcycles. It complies with relevant EU general safety and environmental protection standards and is manufactured using environmentally friendly rubber materials with no harmful additives.

2. Safety & Warnings

Important Safety Information: Read all instructions carefully before use. Improper use may cause tire blowout and vehicle loss of control, resulting in personal injury.

  • Specification Matching Requirements: The inner tube must fully match the original wheel diameter and outer tire specifications. Mixing of mismatched inner tubes/outer tires is strictly prohibited.
  • Air Pressure Specification: Inflate strictly to the standard air pressure marked on the tire. Over-inflation or under-inflation is forbidden to avoid tire blowout and potential riding safety hazards.
  • Installation Specification: Remove sharp debris inside the outer tire during installation to prevent puncturing the inner tube. Check air tightness after installation and do not use until no air leakage is confirmed.
  • Wear and Replacement: Replace with a new product immediately if the outer tire tread is severely worn or cracked, or if the inner tube leaks frequently. Continued use is prohibited.
  • Child Warning: Keep rubber parts of this product away from children to prevent risks of accidental ingestion or suffocation.

3. Setup (Installation Instructions)

3.1. Installation Preparation

  1. Remove the outer tire, and clear any sharp debris and sand from the rim and the inside of the outer tire to prevent scratching the inner tube.
  2. Check that the inner tube has no damage and the outer tire has no cracks or deformation. Confirm that the specifications match your wheel and outer tire.
  3. Inflate the inner tube slightly to let it stretch naturally and avoid twisting or bending during installation.

3.2. Installation Procedures

  1. Place the inner tube flat inside the outer tire.
  2. Straighten the valve stem, ensuring no squeezing or twisting.
  3. Reinstall the outer tire onto the rim.
  4. Inflate the tire evenly to the standard air pressure marked on the tire.
  5. Let the tire stand still to check air tightness. Confirm there is no air leakage from the valve stem and tire body.
  6. Once no air leakage is confirmed, the installation is complete.
Motorcycle inner tube with valve stem
Figure 2: Inner tube showing the valve stem, crucial for proper installation.

4. Operating Instructions

The primary operation involves maintaining correct tire pressure. Always ensure the tire is inflated to the manufacturer's recommended pressure, as indicated on the outer tire. Regularly check the tire pressure before each ride to ensure optimal performance and safety.

5. Maintenance & Care

5.1. Regular Inspection

  • Check tire pressure before every ride.
  • Inspect the wear of the outer tire and air leakage of the inner tube every month.

5.2. Repair Specifications

  • Small punctures on the inner tube can be fixed with cold patching.
  • Direct replacement is required for multiple damages or large-area aging.

5.3. Replacement Cycle

  • Under normal use, the service life of the outer tire is approximately 1-3 years.
  • The service life of the inner tube is approximately 1-2 years. Replace them in a timely manner once they become aged.

5.4. Storage and Maintenance

  • Store idle tires/inner tubes in a cool and dry place.
  • Avoid direct sunlight exposure and high-temperature baking to prevent rubber aging and cracking.
  • Avoid contact with oil stains and chemical corrosives to prevent rubber deterioration and damage.

5.5. Prohibited Operations

  • Do not let sharp objects roll over or scratch the tires.
  • Do not store tires under prolonged exposure to sunlight.
  • Do not inflate with excessive pressure.

6. Troubleshooting

This section addresses common issues you might encounter with your inner tube.

Problem Possible Cause Solution
Frequent Air Leakage Puncture, valve stem issue, aged rubber, improper installation, sharp debris in outer tire. Inspect for punctures (cold patch if small), check valve stem, ensure no debris in outer tire. If frequent or large damage, replace the inner tube.
Tire Blowout Over-inflation, under-inflation, mismatched specifications, severe wear/damage. Ensure correct air pressure. Verify inner tube and outer tire specifications match. Replace severely worn or damaged tubes/tires.
Rapid Deterioration of Rubber Exposure to direct sunlight, high temperatures, oil stains, chemical corrosives. Store in a cool, dry place away from direct sunlight and chemicals.

7. Specifications

Attribute Detail
Product Name Butyl Rubber Inner Tube / Tire
Brand Name HTBCCHB
Model Name 2.75-19, 3.00-19, 19 Inch
Item Type Tyres
Material Butyl Rubber (Metal for valve stem)
Item Diameter 19 inch
Item Weight 0.43 kg
External Testing Certification CE
High-concerned chemical None
Origin Mainland China

8. User Tips

  • Always double-check the inner tube and outer tire sizes to ensure they are a perfect match for your wheel.
  • When installing, take extra care to remove any small stones or sharp objects from inside the tire casing to prevent immediate punctures.
  • A slightly inflated inner tube is easier to position correctly within the outer tire, reducing the risk of pinching.
  • Regularly inspect your tires for signs of wear, cracks, or frequent air loss, and replace them promptly to ensure riding safety.

9. Manufacturer & Support

9.1. Manufacturer Information

Manufacturer: Yongkang Hongtian Trading Co., Ltd.
Address: Changcheng Village, Yongkang Economic Development Zone, Jinhua City, Zhejiang Province, Room 302, 3rd Floor, No. 66 Jinbi Road (self-declaration)
Email: 841996743@qq.com
Phone: 86-13018090962

9.2. EU Authorized Representative

Representative: MJCM SARL
Address: 78 avenue des Champs Elysees Bureau 326
Email: mjcm190928@gmail.com
Phone: 33-767213611

9.3. Additional Resources

For a detailed user manual in PDF format, please refer to the official document available at: User Manual (PDF)

10. Disclaimer

The manufacturer and seller shall not be liable for any tire blowout, vehicle accidents, personal injury, or property loss caused by specification mismatch, abnormal air pressure, improper installation, or man-made damage. Users are responsible for ensuring proper installation and maintenance according to the instructions provided in this manual.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.