MOES BS-FB-V3

Contents

MOES Smart ZigBee Fingerbot Plus User Manual

Model: BS-FB-V3

Home, Smart MOES Home

1. Introduction

The MOES Smart ZigBee Fingerbot Plus is the world's smallest robot designed for smartly controlling various types of buttons and switches. It transforms your existing home appliances into smart devices with robotic clicks, enabling app control, voice commands, and scheduling. This manual provides essential information for safe and effective use of your Fingerbot Plus.

MOES ZigBee Smart Fingerbot Plus product image
MOES ZigBee Smart Fingerbot Plus, compatible with Siri, Alexa, and Google Assistant.
Video: Unboxing and basic setup demonstration of the MOES ZigBee Fingerbot Plus.

2. Product Specifications

FeatureSpecification
ModelBS-FB-V3
Dimensions34.5 x 34.5 x 34.5 mm
Weight38g
Communication ProtocolZigBee 3.0 (BLE 4.2 for older models)
FunctionalitiesApp Control, Voice Control, Cloud Control, Scheduler
Stall Torque2.0 kgf·cm (Upgraded to 15N)
Maximum Arm Movement12mm (Upgraded from 8mm)
Working Temperature-10℃ ~ 45℃ (14°F ~ 131°F)
Battery TypeCR2
Battery Capacity500 mAh (Upgraded to 800mAh)
Clicking Life3K Clicks (Upgraded to 15K Clicks)
Frequency Band2.4GHz
Maximum Radio Transmit Power+4dbm
Fingerbot Plus vs. Fingerbot comparison chart
Comparison of Fingerbot Plus and previous Fingerbot models, highlighting improved clicking life, movement range, force, and battery capacity.

3. Safety Information and Warnings

3.1 General Warnings

  • The product is non-waterproof. Do not install it on or near underwater appliances.
  • The product contains a lithium battery; therefore, it is prohibited in humid, high-temperature environments.
  • Do not hinder the movement of the Fingerbot's arm when it is working. Otherwise, it may cause the arm to fall off and damage the motor inside the Fingerbot.
  • Do not disassemble, reassemble, modify, or attempt to repair this product by yourself. This work should be performed by authorized professionals.

3.2 Battery Warnings

INGESTION HAZARD: This product contains a button cell or coin battery.

  • DEATH or serious injury can occur if ingested. A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours.
  • KEEP new and used batteries OUT OF REACH of CHILDREN.
  • Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.
  • Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children.
  • Do NOT dispose of batteries in household trash or incinerate.
  • Even used batteries may cause severe injury or death.
  • Call a local poison control center for treatment information.
  • Non-rechargeable batteries are not to be recharged.
  • Do not force discharge, recharge, disassemble, heat above 60°C or incinerate. Doing so may result in injury due to venting, leakage, or explosion resulting in chemical burns.
  • Ensure that the battery is correctly loaded into the battery compartment according to the polarity marked, and the positive and negative poles cannot be installed reversely.
  • Do not mix old and new batteries, different brands, or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries.
  • Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations.
  • Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.

4. Package Contents

The standard package for the Fingerbot Plus includes:

  • Fingerbot Plus x 1
  • 3M sticker x 1
  • User manual x 1

Note: The ToolPack (various tool arms) is not included in the standard package with the Fingerbot Plus and needs to be purchased separately from MOES.

Modular design with various tool arms and dimensions
Modular design of the Fingerbot Plus with various tool arms and their dimensions. Tool arms are sold separately.

5. Setup

5.1 Power Supply and Initial Activation

  1. Open the back cover of the Fingerbot Plus.
  2. Remove the insulating paper from the battery compartment.
  3. Long press the reset button until the indicator light flashes to initiate pairing mode.

5.2 App Download and Registration

The MOES App is recommended for controlling your Fingerbot Plus. It offers enhanced compatibility and customized features compared to the Tuya Smart / Smart Life app.

  1. Download the MOES App from the App Store (iOS) or Google Play Store (Android), or scan the QR code below.
  2. Open the MOES App.
  3. If you are a new user, tap "Register" and follow the prompts to create an account. If you already have a MOES account, choose "Log in".
QR code for MOES App download
Scan this QR code to download the MOES App from Google Play or App Store.

5.3 Connecting the Fingerbot Plus to the App

  1. Ensure your phone's Bluetooth is turned ON.
  2. Confirm the Fingerbot's blue indicator light is flashing. If not, press and hold the reset/function button until a prompt tone is heard and the blue light starts slow flashing, indicating it's in distribution network state.
  3. Open the MOES App and click the "+" icon to "Add Device". The app should automatically detect the Fingerbot Plus.
  4. Follow the on-screen instructions to add the device. Once successfully added, you can edit the device name and access its control page.

6. Device Installation

The Fingerbot Plus is designed for flexible installation on various buttons and switches. It uses a 3M adhesive sticker for secure attachment.

  1. Clean the surface of the button or switch panel where you intend to install the Fingerbot Plus.
  2. Attach the Fingerbot Plus to the panel using the provided double-sided 3M sticker.
  3. After installation, it is recommended to let the Fingerbot rest for 24 hours to achieve maximum adhesion.

6.1 Calibrating the Robotic Arm

Connect your Fingerbot Plus with the App and calibrate the movement of its robotic arm to fit your specific switches and buttons. The app allows for adjustable up and down movement (0-100) and sustain time settings.

6.2 Installing Different Tool Arms (Optional, ToolPack sold separately)

The modular design allows you to replace the Fingerbot's arm with various tool pack options to fit different use cases.

6.2.1 Straight Arm Installation

Straight arms are provided in different lengths to assist the Fingerbot in better fitting various button-control cases. Simply slide the desired straight arm into the Fingerbot's slot as shown in the diagram.

Fingerbot Plus with straight arm
The Fingerbot Plus with a straight arm attached, ready to press a button.

6.2.2 Rocker Arm Installation

The rocker arm is used to push and pull rocker switches. Follow these steps:

  1. After connecting Fingerbot with the App, set Fingerbot to the 'Switch' mode.
  2. Move the arm of Fingerbot to the bottom and fix the Fingerbot on the switch panel.
  3. Tear off the tape covering on the rocker arm to stick the arm to the switch button.
  4. After ensuring firmness, use the App to adjust the rising range of Fingerbot's arm so that its movement range can be adapted to the switch button.
  5. If the app shows the opposite status to the actual status, use the 'invert' function to invert the display mode.

6.2.3 Ring Arm Installation

The ring arm is used to push and pull toggle switches. Follow these steps:

  1. After connecting Fingerbot with the App, set Fingerbot to the 'Switch' mode.
  2. Following the picture, fix two cushion blocks to Fingerbot with tape.
  3. Put the ring of the arm on the toggle button, and tear off the tape covering on the other side of the cushion block to fix the Fingerbot on the switch panel.
  4. After ensuring firmness, use the App to adjust the movement range of Fingerbot's arm so that its movement range can be adapted to the toggle.
Fingerbot on various switch types
The Fingerbot Plus can be installed on various switch types including standard buttons, rocker switches, and toggle switches.

7. Operating Instructions

7.1 App Control

You can control the Fingerbot Plus directly via the MOES App (or Tuya Smart/Smart Life App) using Bluetooth or remotely via a ZigBee gateway.

  • Click Function: One tap on the phone activates the Fingerbot to press a button. The same effect is available by pressing the physical button on the Fingerbot Plus.
  • Schedule: Set schedulers in the App to automatically activate the Fingerbot at certain times (e.g., turn on/off lights, coffee maker). A ZigBee hub is required for timing schedules.
  • Sustain Time: Adjust the sustain time in the app for more flexible and accurate control, especially for devices that require a longer press.
Tuya Smart App controlling a coffee maker
Ease your life with the Tuya Smart App for the Fingerbot Plus, allowing you to auto-control your coffee maker via smartphone.
Timer schedule for automatic ON/OFF
Timer your schedule for automatic ON/OFF. Note: The ZigBee hub is a must for timing schedules.
Sustain time setting in the app
Set the Sustain Time for more flexible and accurate control, such as for a coffee machine.

7.2 Voice Control

The Fingerbot Plus is compatible with Amazon Alexa, Google Assistant, and Siri. A ZigBee gateway is required for voice control.

  • Use simple voice commands to trigger your house appliances. For example, "Alexa, turn on the Fingerbot."
Voice control with Alexa for a robot vacuum
Work with Alexa and Google Home for voice control. Use simple voice commands to trigger your house appliances.

7.3 Remote Control (with ZigBee Gateway)

With a ZigBee gateway (purchased separately), you can control your Fingerbot Plus through the Internet from anywhere.

Fingerbot with ZigBee gateway for remote control
Smartly turn on your house floor cleaning robot outdoors in Smart Life App for house cleaning. Note: ZigBee gateway is required for wireless control.
Fingerbot on a garage door opener
Install this ZigBee Fingerbot onto your traditional garage door opener and open it at a preset time when arriving home. Note: ZigBee gateway is required for wireless control.

7.4 Group Control and Device Sharing

You can create groups in the App to manage all Fingerbot Plus devices in your house and share control with family members.

Multiple Fingerbots controlled by one person or one Fingerbot controlled by multiple people
The App allows for flexible control: multiple people can control one Fingerbot, or one person can control multiple Fingerbots.

7.5 Touch Control Panel

The Fingerbot Plus features a new touchable panel, allowing you to trigger switches or buttons manually even if your phone is not in hand.

Fingerbot Plus with touchable panel
New Designed Touchable Panel Fingerbot Plus: Allows you to trigger your switches or buttons manually if you do not have your phone in hand.

7.6 Child Lock Feature

To prevent accidental operations by children, you can disable the touch control feature within the Smart Life App.

Disable Touch Control in Smart Life App
Disable the Touch Control in Smart Life App to avoid misoperations by kids.

8. Maintenance

  • Battery Replacement: When the battery level is low, replace the CR2 battery, ensuring correct polarity. Refer to the battery warnings in Section 3.2.
  • Cleaning: Use a soft, dry cloth to clean the device. Do not use harsh chemicals or liquids.
  • Adhesive: If the 3M sticker loses adhesion, replace it with a new one. Ensure the surface is clean and dry before applying.

9. Troubleshooting

9.1 Common Issues

  • Device not connecting to App:
    1. Ensure your phone's Bluetooth is on.
    2. Confirm the Fingerbot's blue indicator light is flashing (pairing mode). If not, long-press the reset button.
    3. Ensure you are within the ZigBee-compatible connection range (approx. 10 meters) if not using a gateway.
    4. Verify your ZigBee gateway is properly set up and connected to the internet.
    5. Check if the App is updated to the latest version.
  • Voice control not working:
    1. Ensure a ZigBee gateway is connected and properly configured.
    2. Verify the Fingerbot is linked to your voice assistant (Alexa, Google Home, Siri) account.
    3. Check your voice commands for accuracy.
  • Fingerbot not pressing button correctly:
    1. Recalibrate the robotic arm's movement range in the App.
    2. Ensure the Fingerbot is securely attached and aligned with the button/switch.
    3. Check if the correct tool arm (straight, rocker, ring) is installed for the specific switch type.
  • App showing opposite status:
    1. Use the 'invert' function in the App to correct the display mode for rocker/toggle switches.

9.2 Further Assistance

If you encounter persistent problems installing or operating your device, please review its product data sheet or contact customer support.

Product Data Sheet: https://www.moestech.com/blogs/news/bs-fb-v3

10. User Tips

  • ZigBee Gateway is Key: For full smart functionality, including remote control, voice control, and advanced scheduling, a ZigBee gateway (hub) is required and must be purchased separately.
  • Adhesion is Important: After attaching the Fingerbot, allow it to rest for 24 hours to ensure maximum adhesion before heavy use.
  • Experiment with Tool Arms: The modular design allows for different tool arms. Experiment to find the best fit for your specific buttons and switches.
  • Check App Settings: If a switch's status appears inverted in the app, use the 'invert' function to correct it.
  • Child Safety: Utilize the 'Disable Touch Control' feature in the app to prevent unintended operations by children.

11. Declaration of Conformity

Hereby, WENZHOU NOVA NEW ENERGY CO., LTD declares that the radio equipment type BS-FB-V3 is in compliance with Directive 2014/53/EU, 2014/30/EU, and 2011/65/EU.

The full text of the EU declaration of conformity is available at the following internet address: https://www.moestech.com/blogs/news/bs-fb-v3

12. Recycling Information

All products marked with the symbol for separate collection of waste electrical and electronic equipment (WEEE Directive 2012/19/EU) must be disposed of separately from unsorted municipal waste. To protect your health and the environment, this equipment must be disposed of at designated collection points for electrical and electronic equipment designated by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences for the environment and human health. To find out where these collection points are and how they work, contact the installer or your local authority.

Recycling symbols for WEEE and batteries
Recycling symbols indicating separate disposal for electrical and electronic equipment and batteries.

13. Warranty and Support

Thank you for purchasing the MOES Smart ZigBee Fingerbot Plus. We hope you enjoy using it.

13.1 Warranty Instructions

The products are covered by a 24-month warranty, effective from the date of purchase by a retail customer. To exercise warranty rights, the purchaser must present a Warranty card and Proof of purchase (VAT invoice, financial receipt, or other document confirming the actual date of purchase), unless the purchase date comes from the warranty card.

If product quality problems occur within 24 months from the date of receipt, prepare the product and packaging and go to the place or store where you purchased it to apply for after-sales maintenance. If the product is damaged due to personal reasons, a certain maintenance fee will be charged.

The warranty does not cover:

  • Mechanical damage caused by the user's fault and product defects caused by such damage.
  • Damage caused by improper use of the product.
  • Defects due to natural wear and tear during use.

The rights under the guarantee will expire if:

  • The warranty seal is removed from the product.
  • The serial number is removed from the product.
  • Action is taken to eliminate physical defects in the product outside of authorized service.
  • Non-original parts and consumables are used.

Reported defects covered by the warranty will be considered immediately and no later than 14 days from the date of delivery of the goods to the Guarantor. After checking and determining the legality of the warranty claim, the Guarantor's services will repair the product within a reasonable time, not exceeding 30 days from the date of delivery of the goods to the Guarantor. However, if hard-to-find spare parts are required, this deadline may extend the time it takes to deliver the part from the manufacturer's factory.

The warranty does not include the performance of maintenance and similar operations specified in the user manual, and users are obliged to do it themselves.

13.2 Customer Support

Manufacturer: WENZHOU NOVA NEW ENERGY CO., LTD
Address: Power Science and Technology Innovation Center, NO.238, Wei 11 Road, Yueqing Economic Development Zone, Yueqing, Zhejiang, China
Tel: +86-577-57186815
After Service Email: service@moeshouse.com

UK REP (EVATOST CONSULTING LTD):
Address: Suite 11, First Floor, Moy Road Business Centre, Taffs Well, Cardiff, Wales, CF15 7QR
Tel: +44-292-1680945
Email: contact@evatost.com

AMZLAB GmbH:
Address: Laubenhof 23, ESSEN 45326
Email: info@amz-lab.de
Tel: +491745298066

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.