Canon RC-6 Wireless Remote Control

Contents

Canon RC-6 Wireless Remote Control User Manual

Model: RC-6

1. Introduction

The Canon RC-6 Wireless Remote Control is a compact infrared remote controller designed to trigger your compatible Canon EOS camera's shutter release from a distance. This device is ideal for self-portraits, group shots, or any situation where minimizing camera shake is crucial. It supports both immediate shutter release and a 2-second delay mode.

Canon RC-6 Wireless Remote Control front view

Figure 1: Front view of the RC-6 Wireless Remote Control

2. Safety Information

WARNING:

  • Avoid contact with water.
  • Do not disassemble the device by non-professionals.

3. Package Contents

Please check that all items are present:

  • 1 x RC-6 Wireless Remote Control
  • 1 x CR2025 Lithium Battery (may be pre-installed)

4. Setup

4.1. Battery Installation

  1. Locate the battery compartment on the back of the remote control.
  2. Slide the battery tray out.
  3. Insert one CR2025 lithium battery with the positive (+) side facing up.
  4. Slide the battery tray back into the remote control until it clicks into place.
Battery compartment of the remote control with CR2025 battery

Figure 2: Battery compartment showing CR2025 battery

4.2. Camera Preparation

Before using the remote control, you must configure your Canon EOS camera:

  1. Set Drive Mode: On your camera, navigate to the Drive Mode settings.
  2. Select Remote Control Mode: Choose the remote control icon (often a self-timer icon with a remote symbol) or the 2-second delay remote control mode. Refer to your camera's manual for specific instructions on setting the drive mode to remote control.
  3. Ensure Line of Sight: The remote control operates via infrared (IR). Ensure there is a clear line of sight between the remote control and the camera's IR receiver (usually located on the front of the camera body).
Canon RC-6 Wireless Remote Control next to a Canon DSLR camera

Figure 3: Remote control positioned near a compatible Canon camera

5. Operating Instructions

5.1. Basic Operation

  1. Ensure your camera is set to the appropriate remote control drive mode (as described in Section 4.2).
  2. Point the RC-6 remote control towards the camera's IR receiver.
  3. Press the large circular button on the remote control to trigger the shutter.

5.2. Shutter Release Modes

The RC-6 supports two primary shutter release modes, which are typically selected on your camera:

  • Immediate Release: The shutter fires as soon as the button on the remote is pressed.
  • 2-Second Delay: The shutter fires approximately 2 seconds after the button on the remote is pressed, allowing you time to adjust your pose or move out of frame.

5.3. Operating Range

The effective operating range for the RC-6 Wireless Remote Control is approximately 6-10 meters (20-33 feet) under optimal conditions.

6. Compatibility

The RC-6 Wireless Remote Control is compatible with various Canon EOS DSLR cameras that feature a built-in infrared receiver. Compatible models include, but are not limited to:

  • EOS 5D Mark II, EOS 5D Mark III
  • EOS 7D
  • EOS 6D
  • EOS 70D, EOS 60D
  • EOS 700D, EOS 650D, EOS 600D, EOS 550D, EOS 500D, EOS 450D, EOS 400D, EOS 350D, EOS 100D

7. Maintenance

  • Battery Replacement: Replace the CR2025 battery when the remote control stops responding or its range decreases significantly. Refer to Section 4.1 for instructions.
  • Cleaning: Wipe the remote control with a soft, dry cloth. Do not use liquid cleaners or solvents.
  • Storage: Store the remote control in a cool, dry place away from direct sunlight and extreme temperatures.

8. Troubleshooting

8.1. Remote Control Not Working

  • Check Camera Settings: Ensure your camera's drive mode is set to remote control. This is the most common reason for the remote not working.
  • Check Battery: Verify the CR2025 battery is correctly installed and has sufficient charge. Replace if necessary.
  • Line of Sight: Ensure there is a clear, unobstructed path between the remote control and the camera's IR receiver.
  • Operating Range: Make sure you are within the effective operating range (6-10 meters).
  • Infrared vs. Bluetooth/WiFi: This remote operates via infrared. It is not a Bluetooth or WiFi device.

9. Specifications

FeatureDescription
Product NameCanon Wireless Remote Control
TypeInfrared Remote Controller
Operating RangeApprox. 6-10 meters
Dimensions60 x 28 x 7 mm (2.36 x 1.11 x 0.27 inches)
Power Source1 x CR2025 Lithium Battery
Release ModesImmediate, 2-second delay
Product details and specifications sheet

Figure 4: Manufacturer's product details and specifications

10. User Tips

  • Always ensure your camera's drive mode is correctly set to remote control before attempting to use the RC-6.
  • For best results, point the remote directly at the camera's infrared receiver.
  • If the remote doesn't work, double-check the battery installation and ensure the battery is fresh.
  • Familiarize yourself with your camera's specific remote control settings, as they can vary slightly between models.

11. Warranty and Support

For technical support or warranty inquiries, please contact the manufacturer:

  • Manufacturer: Shenzhen Chiyi Technology Co., Ltd
  • Address: 401-43, Buildings 2 and 3, M-10, Maqueling Industrial Zone, Maling Community, Yuehai Street, Nanshan District, Shenzhen, China
  • Email/Tel: smtsykj@163.com / +86 17722493418

An additional user manual in PDF format may be available for download: View User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.